BD3181FVM-TR High-Side Current Sense Amp | ROHM
MPN: BD3181FVM-TR ✓ 啟用中BD3181FVM-TR 概覽
A high-side current-sense amplifier is a specialized analog amplifier used when a load current must be measured without disconnecting the power path. Its place in the signal chain is sensor interface, instrumentation amplifier, analog signal conditioner, and power management IC. Placing the amplifier on the high side of the shunt keeps the measured node near ground potential, which can simplify grounding and improve system-level noise immunity in many power-control applications.
The BD3181FVM-TR includes one amplifier circuit and uses an 8-MSOP package for compact surface-mount layouts. Its high-side architecture supports battery-powered, industrial-control, motor-control, power-supply, and energy-monitoring systems where load-current feedback is required. The MSOP format also provides a defined lead arrangement for automated assembly, although the exact pin functions and exposed thermal-pad arrangement must be assigned from the manufacturer pin-description table before PCB routing is released.
The BD3181FVM family is identified in the manufacturer documentation as a high-side current-sense amplifier family. Because it is intended for measuring differential voltage generated by a shunt, the practical accuracy depends on shunt resistance, amplifier gain, common-mode operating range, offset behavior, supply voltage, and the stability of the reference node. These operating limits must be checked against the complete manufacturer datasheet before the device is used outside its stated conditions.
Typical uses include DC motor current feedback, industrial power-module monitoring, battery charge control, regulated power-supply protection, solenoid-current measurement, and programmable-load monitoring. In each case, the shunt converts current into a differential voltage, while the amplifier conditions that voltage for an analog-to-digital converter, comparator, or controller. The external shunt value must be selected to keep the differential input within the amplifier's specified range while producing an adequate signal at the output.
For PCB design, place the shunt and current-sense amplifier close together so that the two shunt terminals connect directly to the amplifier input pins with minimal loop area. Keep high-current paths separate from sensitive input and output routing, use a quiet ground reference, and decouple the amplifier supply close to its supply pin. These practices reduce offset error and susceptibility to switching-node interference.
This product page combines the exact BD3181FVM-TR identity, package information, application guidance, design considerations, and validated sourcing fields to support faster component selection and PCB planning. For a release-ready design, use the ROHM Semiconductor datasheet and pin-description table to confirm electrical limits, gain options, pin assignments, and recommended application circuitry.
直接替換替代品,適用於 BD3181FVM-TR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品BD3181FVM-TR 最大額定值與電氣特性
| Product Type | High-side current-sense amplifier |
| Amplifier Circuit Count | 1 circuit |
| 封裝 | 8-MSOP |
| Total Pin Count | 8 pins |
| 安裝類型 | Surface mount |
| Input Architecture | High-side current sensing |
| Shipping Format | Tape and reel |
BD3181FVM-TR 8-msop 腳位配置指南
BD3181FVM-TR(8-msop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: BD3181FVM-TR.
請參閱 資料表 以查看完整腳位配置。
典型應用
BD3181FVM-TR 適用於 6 應用s: DC Motor Current Feedback, Industrial Power-Supply Monitoring, Battery Charge and Discharge Control, Solenoid and Actuator Current Measurement, Programmable DC Load and Bench Supply, Battery-Powered Equipment Current Limit.
DC Motor Current Feedback
The BD3181FVM-TR fits a DC motor-control loop that requires the controller to measure armature or supply current without placing a high-voltage sense node at the motor-return ground. A shunt in the motor supply converts current into differential voltage, and the BD3181FVM-TR amplifies that voltage for an analog-to-digital converter or comparator. The designer must choose the shunt so that the maximum motor current remains inside the amplifier's common-mode and input limits, then filter the output for PWM-related switching noise. Because this part provides one amplifier circuit in an 8-MSOP package, it is particularly useful where compact placement, low burden voltage, and simple high-side monitoring are priorities.
Industrial Power-Supply Monitoring
The BD3181FVM-TR can provide the current-measurement element in an industrial power module that monitors a DC output bus, actuator feed, or distributed supply branch. The shunt should be placed in the high-side conductor so that the amplifier measures the small differential voltage generated by load current. The resulting output can support telemetry, overload indication, or adaptive power control. Layout is critical because the sensed difference can be much smaller than surrounding supply noise; keep the Kelvin connections short, isolate them from switching-current paths, and confirm the common-mode range across the complete input-bus operating range before committing the design.
Battery Charge and Discharge Control
The BD3181FVM-TR is applicable to battery systems that require continuous current feedback during charging, discharge, or both. A high-side shunt keeps the measured voltage close to the system ground, which can simplify the amplifier's reference arrangement. The shunt must be selected to balance measurement resolution against conduction loss and heat generation, while the amplifier's supply and common-mode ratings must cover the battery's full voltage range. Designers should also account for transient current at load connection and define output filtering so that a brief inrush event does not incorrectly trigger protection or control decisions.
Solenoid and Actuator Current Measurement
The BD3181FVM-TR can monitor current through a solenoid, valve, relay, or electromechanical actuator when the control system needs a linear representation of coil current. Measuring on the high side keeps the sense amplifier near the power-return reference and enables closed-loop current control or jam detection. The shunt resistance should produce a signal that uses the amplifier's output range efficiently at the highest expected current without violating its input limits. Add protection against inductive voltage spikes and route the shunt connections as a dedicated pair so actuator switching transients do not couple into the measurement signal.
Programmable DC Load and Bench Supply
The BD3181FVM-TR fits programmable DC loads and bench power supplies where the controller must measure output current across a broad operating range. The part's high-side measurement approach permits the shunt to remain in the positive output path while the amplifier reports a ground-referenced voltage. For accurate test results, use a shunt with suitable resistance, power rating, and temperature coefficient, and verify amplifier offset and gain error during calibration. Place the amplifier close to the shunt and keep switching-regulator loops and high-current output conductors physically separated from the differential input route to minimize measurement error.
Battery-Powered Equipment Current Limit
The BD3181FVM-TR can support current-limit supervision in battery-powered equipment where the system must distinguish normal load current from an excessive draw. The high-side shunt provides a proportional measurement without interrupting the load path, while the amplifier output can drive a comparator or ADC channel. Because the device has one amplifier circuit in an 8-MSOP package, it enables a compact implementation in portable instruments and energy-harvesting equipment. The system designer must verify the amplifier supply range, quiescent demand, common-mode margin, and output behavior during battery discharge before using it as the sole protection element.
工程參考資料,適用於 BD3181FVM-TR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Product Type | High-side current-sense amplifier |
| Brand | ROHM Semiconductor |
| Package | 8-MSOP |
| Amplifier Circuit Count | 1 circuit |
| Total Pin Count | 8 pins |
| Mounting Type | Surface mount |
主要差異化特點
- Purpose-built high-side measurement in a compact package (對比General-purpose operational amplifier)
- Small-package surface-mount implementation (對比Larger instrumentation-amplifier package)
- Single-circuit architecture for focused designs (對比Multi-channel current-sense amplifier)
設計說明
Place the BD3181FVM-TR next to the shunt and connect the differential inputs directly to the shunt terminals with short, symmetric traces. Avoid routing the sensitive input pair alongside a high-current conductor or switching-node copper. A compact Kelvin-style connection reduces parasitic resistance and inductance, limits input offset caused by trace resistance, and improves rejection of common-mode switching noise.
Use a dedicated ground return for the amplifier, shunt, and measurement system instead of allowing sense current to flow through a shared return path. Ground potentials that appear between the shunt and amplifier inputs become measurement error because the part senses a difference between two nodes. Check the assembled PCB for unintended copper loops and keep the high-current path spatially separated from the amplifier and its reference connections.
Select the shunt resistance from the maximum expected current, amplifier input range, allowable power dissipation, and desired measurement resolution. The shunt's continuous dissipation is estimated as I²R, while its temperature rise must remain within the resistor's rating. Validate this calculation against the amplifier's common-mode limits because a larger shunt improves signal resolution but reduces the remaining input-voltage margin.
Do not determine the BD3181FVM-TR pin functions from visual package orientation alone. Use the pin-description table in the ROHM Semiconductor datasheet, then verify the differential input polarity, output pin, supply pins, and ground connection against the PCB netlist. Also confirm that the selected output reference is compatible with the ADC, comparator, or controller input to avoid incorrect readings or output saturation.
Current-sense signals are often small and can be affected by PWM edges, relay transients, and magnetic fields. Keep the shunt-current loop compact, use a continuous reference plane, and apply filtering only after accounting for the bandwidth required by the control loop. If an RC filter is added at the output, recalculate its effect on transient response rather than selecting a cutoff based only on nominal output noise.
合規資訊
Compliance attributes were not confirmed for the exact BD3181FVM-TR ordering code. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status require confirmation from ROHM Semiconductor.