CD4050BCM - 6-Channel 3-18V CMOS Buffer | onsemi
MPN: CD4050BCM ✓ 啟用中CD4050BCM 概覽
A CMOS logic buffer is a digital semiconductor that reproduces the logical state of its input at its output while adding drive strength and isolation. The CD4050 series belongs to the CD4000 CMOS logic family, whose low-power operation and high noise immunity make it suitable for industrial control, interface conditioning, and systems that combine low-voltage control signals with moderate-load logic. Unlike an open-collector buffer, this device uses a push-pull output configuration for faster transitions and more predictable behavior at low output impedance.
The principal device characteristics are a 3 V to 18 V supply range, six non-inverting channels, one logic bit per element, push-pull outputs, and a 16-pin SOIC package. According to the manufacturer information, the CD4050 family is designed for logic-level conversion using a single VDD supply. This makes it useful when a signal source and the receiving logic operate from the same supply rail but still benefit from a separate buffered output stage.
The three-state CD4053B appears in a comparison listing as a superficially similar alternative, but its three-state outputs and additional control function make it functionally different from the always-enabled CD4050BCM. A CD4000-series cross-reference is more useful for identifying functional equivalents than for guaranteeing package compatibility. Engineers should still verify the exact suffix, package drawing, supply limits, input levels, propagation delay, output-current capability, and temperature grade before approving a substitute.
Typical applications include buffering control signals in industrial automation equipment, conditioning sensor and interface signals, supporting multiple logic rails in embedded systems, and driving compatible CMOS inputs in test and measurement equipment. Because the CD4050BCM provides independent buffers, designers can use each channel separately rather than combining inputs electrically.
The principal PCB consideration is to place the device close to the protected logic inputs and route each output to the intended load with minimal trace length. Decoupling requirements, unused-channel handling, input rise and fall times, and output drive limits should be taken from the manufacturer datasheet. This page combines device identification, sourcing guidance, verified alternatives, comparison criteria, and practical design considerations to support an engineering replacement decision.
直接替換替代品,適用於 CD4050BCM — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MC14050BDR2G
✅ 直接替換📋 參考替代品(不在目錄中)
HEF4050BP
✅ 直接替換📋 參考替代品(不在目錄中)
CD4050BCM 最大額定值與電氣特性
| Product Type | Hex non-inverting CMOS buffer |
| Number of Channels | 6 channels |
| Bits per Element | 1 bit per element |
| Supply Voltage Range | 3 V to 18 V |
| Logic Family | CD4000 CMOS series |
| Output Polarity | Non-inverting |
| 輸出類型 | Push-pull |
| Technology | Complementary MOS using N-channel and P-channel enhancement-mode transistors |
| Level-Shift Capability | Logic-level conversion using one VDD supply |
| 封裝 | 16-pin SOIC |
| 安裝類型 | Surface mount |
| Lead Count | 16 leads |
| Output-State Control | No dedicated output-enable function |
CD4050BCM 腳位配置
| 腳位 1 | A IN — Non-inverting buffer A input |
| 腳位 2 | A OUT — Non-inverting buffer A output |
| 腳位 3 | B IN — Non-inverting buffer B input |
| 腳位 4 | B OUT — Non-inverting buffer B output |
| 腳位 5 | C IN — Non-inverting buffer C input |
| 腳位 6 | C OUT — Non-inverting buffer C output |
| 腳位 7 | NC — Not connected |
| 腳位 8 | VSS — Ground reference |
| 腳位 9 | D IN — Non-inverting buffer D input |
| 腳位 10 | D OUT — Non-inverting buffer D output |
| 腳位 11 | NC — Not connected |
| 腳位 12 | E IN — Non-inverting buffer E input |
| 腳位 13 | E OUT — Non-inverting buffer E output |
| 腳位 14 | F IN — Non-inverting buffer F input |
| 腳位 15 | F OUT — Non-inverting buffer F output |
| 腳位 16 | VDD — Positive supply voltage |
典型應用
CD4050BCM 適用於 6 應用s: Industrial Control Signal Conditioning, CMOS Logic Rail Isolation, Sensor and Interface Conditioning, Test and Measurement Control Logic, Embedded System Power-Control Signals, Network Interface Control.
Industrial Control Signal Conditioning
The CD4050BCM fits industrial control designs that require several control signals to be buffered before entering a CMOS logic stage. Its six independent, non-inverting channels preserve the original Boolean relationship, while the push-pull outputs provide a defined low-impedance drive path. The 3 V to 18 V operating range supports logic systems operating within that range, and the 16-pin SOIC supports compact surface-mount layouts. Each input should drive only one channel, and the design must respect the manufacturer limits for output current, input rise and fall times, supply decoupling, and unused inputs. For factory equipment, confirm the exact temperature grade and qualification requirements before approving the part for a deployed control board.
推薦
CMOS Logic Rail Isolation
The CD4050BCM can buffer multiple digital-control lines on a mixed-signal or embedded controller board. Because all six channels are non-inverting, each output follows the corresponding input and avoids the software or schematic reversal associated with an inverting buffer. Its single-supply architecture supports the logic-level conversion role identified by the manufacturer, provided the input and output levels remain compatible with the selected VDD. The part is particularly useful where a controller or sensor output needs local buffering before reaching another logic block. Designers should route each buffered output away from high-impedance test points, avoid excessive capacitive loading, and confirm propagation-delay requirements against the maximum clock or control-edge rate.
推薦
Sensor and Interface Conditioning
The CD4050BCM is useful for conditioning discrete outputs from sensors, switches, and interface circuits before they reach a CMOS logic input. Six channels allow several low-current signals to be handled independently without combining them at a common node. The non-inverting configuration preserves sensor-output polarity, and the push-pull buffer stage provides a stronger, more deterministic transition than a passive connection to a high-impedance load. The design must still confirm that the upstream signal amplitude meets the CD4050BCM input thresholds at the selected supply voltage. Use short traces, maintain a common ground reference, and avoid using the buffer as a high-current line driver when its specified output-current capability is insufficient.
推薦
Test and Measurement Control Logic
The CD4050BCM can provide repeated, non-inverting control outputs in test and measurement equipment where several digital settings must reach instrument logic reliably. Its six channels allow separate control and status lines to be buffered while retaining their intended polarity. The 16-pin SOIC is practical for compact instrument-control boards, and the 3 V to 18 V range permits operation across several conventional logic supplies. The primary qualification checks are output rise and fall time, propagation delay, capacitive-load behavior, and current available from each channel. Keep output traces short and use controlled impedance or buffering when driving long cables, since a logic buffer is not a substitute for a dedicated line driver.
推薦
Embedded System Power-Control Signals
The CD4050BCM fits embedded systems that require buffered enable, reset, mode, or peripheral-control signals at a common logic voltage. Its non-inverting channels preserve the firmware-visible relationship between a control output and the downstream circuit, while the push-pull outputs reduce sensitivity to leakage in downstream CMOS inputs. A 3 V to 18 V supply range offers flexibility across embedded logic families, but every connected load must remain within the device's input and output ratings. In power-control systems, ensure that active-high and active-low controls are handled consistently; the buffer cannot invert a signal. Also avoid placing the device in a shutdown path unless its output state during power loss has been confirmed from the manufacturer documentation.
推薦
Network Interface Control
The CD4050BCM can condition local digital control signals in network-interface and communication equipment, including status indicators, hardware enables, and command lines entering legacy CMOS logic. Six buffered channels can reduce loading from control nets and maintain non-inverting command polarity. The 16-pin SOIC is convenient for dense interface boards, while operation from 3 V to 18 V supports integration with conventional CMOS interface logic. Ensure that any externally exposed or long-trace signals have suitable protection and that the device's output drive is adequate for the connected load. For high-speed data paths, use a dedicated transceiver or line driver instead, because the CD4050BCM is a general-purpose logic buffer rather than a specified high-speed communications device.
推薦
推薦產品摘要
工程參考資料,適用於 CD4050BCM — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MC14050BDR2G | HEF4050BP |
|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | onsemi | onsemi | NXP Semiconductors |
| Function | Hex non-inverting buffer | Hex CMOS buffer | Hex CD4050-series buffer |
| Number of Channels | 6 channels | 6 channels | 6 channels |
主要差異化特點
- Explicit six-channel non-inverting configuration (對比MC14050BDR2G)
- Single-supply logic-level conversion (對比HEF4050BP)
- Compact 16-pin SOIC implementation (對比MC14050BDR2G)
設計說明
Do not approve a replacement from the family name alone. The CD4050BCM must preserve non-inverting logic polarity, use the same 16-pin SOIC footprint, and satisfy the circuit's 3 V to 18 V supply conditions. MC14050BDR2G and HEF4050BP are plausible CD4000-series candidates, but their exact ordering-code data must be checked for output polarity, propagation delay, output current, and temperature grade before installation.
Place the CD4050BCM close to the logic inputs that require buffering and route each output directly to its destination. Keep the ground return short and use a common ground reference between the buffer and receiving circuit. Avoid long parallel output traces where simultaneous switching could increase coupling. The device provides six independent buffers, so do not combine unrelated input signals onto one node merely to reduce pin usage.
Supply the device only within its documented 3 V to 18 V range and follow the manufacturer recommendations for bypass capacitance and input rise and fall times. A push-pull output can source and sink current, but each channel still has a finite drive limit. Check the worst-case load current and total supply demand rather than assuming every channel can operate simultaneously at its individual maximum rating.
合規資訊
The manufacturer-specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations for CD4050BCM were not identified in the available product information.