Analog Devices

DG212DJ+ - Quad SPST CMOS Analog Switch | Analog Devices

MPN: DG212DJ+ ✓ 啟用中
+4.5 V to +18 V Vdss 175 ohm Rds(on) 16-pin PDIP Package
MOQ: 1 |

DG212DJ+ 概覽

The Analog Devices DG212DJ+ is a quad SPST CMOS analog switch with four normally open, independently controlled circuits, a 175 ohm on resistance, and a 16-pin PDIP package. It accepts positive and negative supply voltages from ±4.5 V to ±18 V, making it suitable for routing bipolar analog signals across industrial, instrumentation, communications, and test systems. Each switch provides 1:1 signal-path routing and is controlled by CMOS-compatible logic inputs.

A CMOS analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. Within the signal-chain hierarchy, it belongs to the switch and multiplexer family, which falls under interface ICs and ultimately supports the wider category of semiconductor signal-routing components. Unlike a mechanical relay, the DG212DJ+ changes state electronically without mechanical moving parts, making it appropriate for compact systems requiring fast, repeatable routing.

The DG212 family provides four independent SPST switches in one package. Its stated 175 ohm on resistance is suitable for moderate-impedance signal paths, while the single-pole, single-throw configuration provides a straightforward open-state isolation path. The broad ±4.5 V to ±18 V supply range supports both single-supply arrangements with an appropriate ground reference and dual-supply systems that carry bipolar signals. Latch-up protection is specified when power is disconnected while input signals remain connected.

The DG212 uses normally open switches, meaning each signal path is disconnected until its corresponding control input is asserted. The DG212 and DG202 families share the quad SPST format, but their control logic differs: the DG212 has inverted control relative to the DG202. This distinction must be checked against the existing logic levels and polarity before replacing a device on a PCB.

Typical uses include precision signal routing in test and measurement equipment, multiplexed sensor acquisition, bipolar audio and communication paths, sample-and-hold systems, and industrial control modules. Because the device supports ±18 V supplies and four switch circuits, it can reduce the number of external discrete switches required in a compact analog front end.

The principal design consideration is signal-path loading. With 175 ohm on resistance, the switch contributes to source and destination impedance, so downstream input impedance and cable capacitance should be evaluated together. Keep control traces away from sensitive analog inputs, observe the specified supply sequencing conditions, and use the manufacturer pin-description table when assigning PCB tracks.

This page combines the manufacturer product description, distributor package information, cross-reference findings, practical application guidance, and drop-in comparison notes. It is intended to help engineers determine whether the DG212DJ+ fits the required logic polarity, voltage range, package, and analog routing performance before requesting a quotation.

直接替換替代品,適用於 DG212DJ+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: DG212DJ+ (相同外形與佔位) — 差異在於 On Resistance, Switch Configuration.

Intersil
On Resistance: 175 ohm maximum
Switch Configuration: 4 x SPST
比較對象 DG212DJ+ →

DG212CJ-2

✅ 直接替換
📦 16-pin PDIP
Same DIP terminals and principal functional characteristics; the cross-reference identifies it as a complete replacement, while exact control and temperature details require confirmation

📋 參考替代品(不在目錄中)

DG212CJ+

✅ 直接替換
Intersil
📦 16-pin PDIP
4 channels · 4 x SPST · Normally open · 175 ohm maximum · ±4.5 V to ±18 V · 1000 ns maximum · 500 ns maximum · Inverted digital control inputs

聯絡詢價

查看資料表 →

DG212BDJ

✅ 直接替換
📦 16-pin PDIP
Same 16-PDIP format and DG212-family function, but on resistance is 85 ohm versus 175 ohm, a 90 ohm or 51.4% lower on the DG212BDJ

📋 參考替代品(不在目錄中)

DG212DJ+ 最大額定值與電氣特性

Number of Circuits 4 circuits
Switch Configuration 1:1 SPST
Switch Type Normally open SPST
On Resistance 175 ohm
Positive Supply Voltage Range +4.5 V to +18 V
Negative Supply Voltage Range -4.5 V to -18 V
Supply Voltage Range ±4.5 V to ±18 V
Control Logic CMOS-compatible
Control Polarity Inverted relative to DG202
Latch-Up Protection Guaranteed with input signals connected during power-supply disconnection
封裝 16-pin PDIP
安裝類型 Through-hole
Lead-Free Status Lead Free
RoHS 狀態 RoHS Compliant
Production Status PRODUCTION

DG212DJ+ 16-pin pdip 腳位配置指南

DG212DJ+(16-pin pdip 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

DG212DJ+ 的 16-pin pdip 封裝腳位圖

無詳細腳位定義資料: DG212DJ+.

請參閱 資料表 以查看完整腳位配置。

典型應用

DG212DJ+ 適用於 6 應用s: Precision Test and Measurement Routing, Bipolar Sensor Signal Multiplexing, Industrial Control Signal Routing, Audio and Communication Path Selection, Sample-and-Hold Acquisition Networks, Laboratory Automation and Remote Control.

🔧

Precision Test and Measurement Routing

The DG212DJ+ fits instrument signal-routing modules that must connect one source to a destination under digital control. Four independent SPST paths provide flexible point-to-point selection, while the 175 ohm on resistance can be acceptable when the receiving circuit has substantially higher input impedance. Using the device between a low-level source and a measurement front end reduces the number of discrete relays required. Confirm that switch capacitance, off leakage, charge injection, and signal limits satisfy the required measurement accuracy before finalizing the channel.

🧩

Bipolar Sensor Signal Multiplexing

The DG212DJ+ is appropriate for multiplexing bipolar sensor outputs when the selected instrument or amplifier can tolerate a 175 ohm series resistance. Its ±4.5 V to ±18 V supply capability supports positive and negative sensing ranges, and the normally open SPST configuration provides straightforward channel isolation. Each control signal determines whether one sensor path connects to the shared acquisition node. Engineers should compare the switch resistance with the sensor impedance and ADC sampling network, especially when low-level transducer signals require minimal attenuation.

🏭

Industrial Control Signal Routing

The DG212DJ+ can route bipolar control or feedback signals in industrial modules because it combines four switch circuits with supply operation from ±4.5 V to ±18 V. Its CMOS-compatible control inputs simplify integration with digital controller logic, and the integrated implementation reduces board area compared with four discrete relays. The principal limitation is the 175 ohm on resistance, which can create voltage division when driving a lower-impedance input. Confirm isolation behavior, permissible signal levels, and power-supply tolerances for the specific industrial environment.

🌐

Audio and Communication Path Selection

The DG212DJ+ can select balanced or unbalanced analog paths in communication and audio equipment when source impedance keeps the 175 ohm switch resistance acceptable. The four SPST channels support independent routing of line-level signals, while the bipolar supply range accommodates dual-rail analog circuitry. Its electronic switching avoids relay-contact bounce and mechanical wear, supporting repeated automated path selection. Designers must verify the maximum signal amplitude, bandwidth, off leakage, and distortion-related charge injection before using the switch in precision audio paths.

📺

Sample-and-Hold Acquisition Networks

The DG212DJ+ can implement disconnect and reconnect functions around a sample-and-hold input because each normally open SPST channel provides an explicit open state. The four channels can support hold paths, reset paths, or multiple acquisition inputs when the selected source impedance remains sufficiently high. The 175 ohm on resistance must be included in the settling-time calculation, while switch capacitance and charge injection affect dynamic acquisition accuracy. Use the DG212 data sheet to establish the actual timing and transient limits before defining the sampling interval.

⚡

Laboratory Automation and Remote Control

The DG212DJ+ supports laboratory automation systems that switch external analog fixtures under firmware control. Four integrated switch channels reduce component count, and CMOS-compatible control permits direct interfacing with common control logic levels. The package uses through-hole leads, which can be advantageous for manually wired prototypes or systems assembled around DIP interconnects. Because the device is rated for bipolar supplies up to ±18 V, it can support compatible positive and negative fixture signals. Check input limits and off-state isolation to avoid loading sensitive sources.

What is the DG212DJ+?
The DG212DJ+ is a production quad SPST CMOS analog switch from Analog Devices, packaged in a 16-pin PDIP. It contains four independent normally open switch paths, each with a stated on resistance of 175 ohm. The device accepts positive and negative supplies from ±4.5 V to ±18 V and is controlled by CMOS-compatible logic, making it suitable for general-purpose analog signal routing.
Where can I download the DG212DJ+ datasheet PDF?
The official DG212 datasheet and product resources are available through Analog Devices at https://www.analog.com/en/products/dg212.html. The product page identifies the DG202 and DG212 as quad, normally open SPST CMOS analog switches and links to the production data sheet. Use the package-specific pin table and electrical characteristics on that page when planning a DG212DJ+ design.
What is the supply voltage range of DG212DJ+?
The DG212DJ+ supports positive and negative supply voltages from ±4.5 V to ±18 V. This range allows operation from dual bipolar rails as well as suitable single-supply arrangements when the circuit reference is established correctly. According to the Analog Devices DG212 product description, the switches can remain connected to input signals while the power supplies are disconnected without latching up.
What are the key specifications of DG212DJ+ that engineers should know?
The essential DG212DJ+ specifications are four normally open SPST circuits, 175 ohm on resistance, operation from ±4.5 V to ±18 V, CMOS-compatible control, and a 16-pin PDIP package. The device is listed as PRODUCTION by Analog Devices. Its control polarity is inverted relative to the DG202, which is the most important distinction when comparing the two families.
Is DG212DJ+ pin-compatible with DG212CJ-2?
The DG212CJ-2 is identified by the cross-reference information as a complete DIP replacement whose terminals, package, and principal functional characteristics are consistent with the DG212DJ+. Confirm the exact control-input truth table and operating-temperature markings before production use. For automated boards, compare the DG212 data-sheet ordering information and package drawing against the fitted part.
What is the difference between DG212DJ+ and DG212CJ+?
The DG212DJ+ and DG212CJ+ belong to the same DG212 family and use a 16-pin PDIP format, but the package suffix identifies different ordering variants. The cross-reference information specifically identifies DG212CJ-2 as a complete DIP replacement for the DG212DJ+ because its package, terminals, and principal performance characteristics match. Verify the temperature range, control polarity, and marking before substitution.
When should I choose DG212DJ+ over another DG212-family switch?
Choose the DG212DJ+ when the design requires four normally open SPST paths, a 175 ohm on resistance, CMOS-compatible controls, and a 16-pin PDIP package. Select a lower-resistance family member only when the source and destination impedances justify its different switching characteristics. Select the DG202 instead when its non-inverted control polarity matches the system logic more directly.
Is DG212DJ+ suitable for bipolar analog signal routing?
Yes, the DG212DJ+ is suitable for routing bipolar analog signals because its supplies cover ±4.5 V to ±18 V and each switch is a normally open SPST path. Its 175 ohm on resistance must be included in the total source impedance seen by the receiving circuit. Confirm that signal amplitudes remain within the switch's input and output limits for the selected rail voltages.
What can replace the DG212DJ+?
The DG212CJ-2 is the clearest drop-in candidate identified by the cross-reference information because it is described as a complete DIP replacement with consistent terminals, package, and principal functional characteristics. The Vishay Siliconix DG212BDJ also appears in a 16-PDIP package, but its stated 85 ohm on resistance differs substantially from the DG212DJ+ value of 175 ohm. Review both the logic truth table and signal-path limits before choosing a substitute.
What is the best Vishay Siliconix equivalent for DG212DJ+?
The Vishay Siliconix DG212BDJ is a documented 16-PDIP DG212-family alternative, making it the closest identified Vishay option for package-based comparison. Its stated 85 ohm on resistance differs from the DG212DJ+ value of 175 ohm, while other operating details still require confirmation. It should be treated as a family cross-reference candidate rather than assumed equivalent without checking the data sheet and logic polarity.
Does DG212DJ+ require protection from power-supply sequencing?
The DG212DJ+ is designed to avoid latch-up when the power supplies are disconnected while input signals remain connected, according to the Analog Devices product description. Designers should still observe the data-sheet operating limits and use appropriate signal and supply arrangements. The latch-up guarantee does not remove the need to keep signal amplitudes within the permitted input range.
Where to buy DG212DJ+ online?
Use the Request a Quote form on this page to ask for DG212DJ+ availability, packaging, and lead time from XAIPART. The exact manufacturer ordering code is DG212DJ+, and the component is identified in a 16-pin PDIP package. A quotation request is the appropriate route for current commercial confirmation because inventory and commercial terms can change.
What is the price of DG212DJ+?
Request the current DG212DJ+ quotation through the Request a Quote form on this page. The structured pricing area contains only explicit quantity-break pricing for the exact ordering code, and the current listing set does not contain a qualifying USD quantity-break table. XAIPART can confirm the appropriate commercial response for the requested quantity and packaging.
What is the lead time for DG212DJ+?
Request the current DG212DJ+ lead time through the Request a Quote form on this page. Lead time depends on manufacturer inventory, the requested package quantity, and current allocation conditions. Analog Devices lists the DG212 family as PRODUCTION, but production status alone does not establish a guaranteed delivery interval for each order.
Is DG212DJ+ in stock?
Use the Request a Quote form on this page to request a current DG212DJ+ stock confirmation. Some distributor listings identify inventory, but those records do not establish the quantity available through XAIPART. The exact DG212DJ+ ordering code and requested quantity should be included in the quotation request for an actionable availability response.

工程參考資料,適用於 DG212DJ+ — 比較、設計指引及合規資訊。

選型指南

Choose the DG212DJ+ for systems requiring four independent normally open SPST paths, CMOS-compatible control, bipolar operation, and a 16-pin PDIP footprint. Its 175 ohm on resistance is suitable when the receiving circuit has substantially higher input impedance and signal accuracy is not dominated by series resistance. Consider the Vishay DG212BDJ when its documented 85 ohm on resistance materially improves source loading, after verifying its control logic, limits, and operating-temperature details. The Maxim Integrated DG212CJ-2 is the most explicitly documented complete DIP replacement candidate, making it attractive when the package, terminals, and principal functional characteristics match the required circuit. Do not choose between DG212 and DG202 based only on package or SPST configuration: the DG212 uses inverted control relative to DG202. For any replacement, confirm the truth table, supply range, input limits, temperature grade, and package drawing against the manufacturer data sheet.

與替代品比較

參數 本產品 DG212CJ-2 DG212CJ+ DG212BDJ
Brand Analog Devices Maxim Integrated Maxim Integrated Vishay Intertechnology
Package 16-pin PDIP 16-pin PDIP - same 16-pin PDIP - same 16-pin PDIP - same
Number of Circuits 4 circuits 4 circuits 4 circuits 4 circuits
Switch Configuration 1:1 SPST SPST SPST SPST
Normal Switch State Normally open Normally open Normally open Normally open

主要差異化特點

  • Four independent analog switches in one DIP package (對比DG419DY+)
  • Documented complete DIP replacement option (對比DG212CJ-2)
  • Clear identification of a lower-resistance Vishay option (對比DG212BDJ)

設計說明

Include the DG212DJ+ on resistance in the complete source-impedance calculation. The stated path resistance is 175 ohm, so a 1 kohm receiver plus a 100 ohm upstream source can attenuate the transferred voltage even though the switch is electrically closed. Use the manufacturer data sheet to add switch capacitance and off-state leakage to the settling and acquisition-error analysis, particularly for high-impedance sensor nodes.

Design the positive and negative rails for the full ±4.5 V to ±18 V operating range and decouple each supply close to the device. Keep analog input and output traces away from switching supply nodes, and route control signals separately from sensitive paths. The DG212 family is designed to avoid latch-up when power is removed with signals connected, but that protection does not replace verification of signal amplitudes and supply operating limits.

Use the 16-pin PDIP land pattern and follow the manufacturer pin-description table when assigning tracks. The four switch paths are independent, so avoid unnecessary shared copper between channels that could increase coupling or reduce isolation. Provide adequate clearance around input, output, and control pins, and use a common quiet ground strategy for analog routing to minimize switching transients reaching the source circuit.

Do not substitute the DG212 for the DG202 without checking control polarity. The DG212 has inverted control relative to the DG202, and swapping these families can reverse every channel's commanded state. Also verify the exact ordering suffix, temperature grade, and package variant when using a DG212-family replacement, since family membership alone does not guarantee identical production limits.

合規資訊

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Yes
無鹵
Unknown
衝突礦產
Unknown

The DG212DJ+ is identified as lead free and RoHS compliant. Reach, halogen-free status, and conflict-minerals status are not stated.

資料驗證日期: 2026-11-10 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

dg212 datasheet DG212DJ+ datasheet DG212DJ+ datasheet pdf DG212DJ+ pinout DG212DJ+ specifications Analog Devices DG212DJ+ DG212DJ+ 16-pin PDIP DG212DJ+ 175 ohm SPST DG212DJ+ replacement DG212DJ+ equivalent DG212DJ+ vs DG212CJ+ DG212DJ+ price DG212DJ+ stock DG212DJ+ analog switch application

相關元件與詞彙

Analog Devices Maxim Integrated Vishay Intertechnology DG212DJ+ DG212CJ-2 DG212CJ+ DG212BDJ DG202 DG211 DG201 SPST CMOS analog switch normally open switch analog switch multiplexer interface IC semiconductor on resistance 175 ohm 16-pin PDIP bipolar signal latch-up protection RoHS lead-free
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情