DG212DJ+ - Quad SPST CMOS Analog Switch | Analog Devices
MPN: DG212DJ+ ✓ فعالDG212DJ+ نمای کلی
A CMOS analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. Within the signal-chain hierarchy, it belongs to the switch and multiplexer family, which falls under interface ICs and ultimately supports the wider category of semiconductor signal-routing components. Unlike a mechanical relay, the DG212DJ+ changes state electronically without mechanical moving parts, making it appropriate for compact systems requiring fast, repeatable routing.
The DG212 family provides four independent SPST switches in one package. Its stated 175 ohm on resistance is suitable for moderate-impedance signal paths, while the single-pole, single-throw configuration provides a straightforward open-state isolation path. The broad ±4.5 V to ±18 V supply range supports both single-supply arrangements with an appropriate ground reference and dual-supply systems that carry bipolar signals. Latch-up protection is specified when power is disconnected while input signals remain connected.
The DG212 uses normally open switches, meaning each signal path is disconnected until its corresponding control input is asserted. The DG212 and DG202 families share the quad SPST format, but their control logic differs: the DG212 has inverted control relative to the DG202. This distinction must be checked against the existing logic levels and polarity before replacing a device on a PCB.
Typical uses include precision signal routing in test and measurement equipment, multiplexed sensor acquisition, bipolar audio and communication paths, sample-and-hold systems, and industrial control modules. Because the device supports ±18 V supplies and four switch circuits, it can reduce the number of external discrete switches required in a compact analog front end.
The principal design consideration is signal-path loading. With 175 ohm on resistance, the switch contributes to source and destination impedance, so downstream input impedance and cable capacitance should be evaluated together. Keep control traces away from sensitive analog inputs, observe the specified supply sequencing conditions, and use the manufacturer pin-description table when assigning PCB tracks.
This page combines the manufacturer product description, distributor package information, cross-reference findings, practical application guidance, and drop-in comparison notes. It is intended to help engineers determine whether the DG212DJ+ fits the required logic polarity, voltage range, package, and analog routing performance before requesting a quotation.
جایگزینهای drop-in برای DG212DJ+ — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای DG212DJ+ (همان فرمفاکتور و فوتپرینت) — متفاوت در On Resistance, Switch Configuration.
DG212CJ-2
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
DG212CJ+
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←DG212BDJ
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
DG212DJ+ حداکثر مقادیر مجاز و مشخصات الکتریکی
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 SPST |
| Switch Type | Normally open SPST |
| On Resistance | 175 ohm |
| Positive Supply Voltage Range | +4.5 V to +18 V |
| Negative Supply Voltage Range | -4.5 V to -18 V |
| Supply Voltage Range | ±4.5 V to ±18 V |
| Control Logic | CMOS-compatible |
| Control Polarity | Inverted relative to DG202 |
| Latch-Up Protection | Guaranteed with input signals connected during power-supply disconnection |
| بستهبندی | 16-pin PDIP |
| نوع نصب | Through-hole |
| Lead-Free Status | Lead Free |
| وضعیت RoHS | RoHS Compliant |
| Production Status | PRODUCTION |
راهنمای پیکربندی پین DG212DJ+ 16-pin pdip
پیکربندی پین برای DG212DJ+ (پکیج 16-pin pdip). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای DG212DJ+.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
DG212DJ+ مناسب است برای 6 کاربردs: Precision Test and Measurement Routing, Bipolar Sensor Signal Multiplexing, Industrial Control Signal Routing, Audio and Communication Path Selection, Sample-and-Hold Acquisition Networks, Laboratory Automation and Remote Control.
Precision Test and Measurement Routing
The DG212DJ+ fits instrument signal-routing modules that must connect one source to a destination under digital control. Four independent SPST paths provide flexible point-to-point selection, while the 175 ohm on resistance can be acceptable when the receiving circuit has substantially higher input impedance. Using the device between a low-level source and a measurement front end reduces the number of discrete relays required. Confirm that switch capacitance, off leakage, charge injection, and signal limits satisfy the required measurement accuracy before finalizing the channel.
پیشنهادی
Bipolar Sensor Signal Multiplexing
The DG212DJ+ is appropriate for multiplexing bipolar sensor outputs when the selected instrument or amplifier can tolerate a 175 ohm series resistance. Its ±4.5 V to ±18 V supply capability supports positive and negative sensing ranges, and the normally open SPST configuration provides straightforward channel isolation. Each control signal determines whether one sensor path connects to the shared acquisition node. Engineers should compare the switch resistance with the sensor impedance and ADC sampling network, especially when low-level transducer signals require minimal attenuation.
پیشنهادی
Industrial Control Signal Routing
The DG212DJ+ can route bipolar control or feedback signals in industrial modules because it combines four switch circuits with supply operation from ±4.5 V to ±18 V. Its CMOS-compatible control inputs simplify integration with digital controller logic, and the integrated implementation reduces board area compared with four discrete relays. The principal limitation is the 175 ohm on resistance, which can create voltage division when driving a lower-impedance input. Confirm isolation behavior, permissible signal levels, and power-supply tolerances for the specific industrial environment.
پیشنهادی
Audio and Communication Path Selection
The DG212DJ+ can select balanced or unbalanced analog paths in communication and audio equipment when source impedance keeps the 175 ohm switch resistance acceptable. The four SPST channels support independent routing of line-level signals, while the bipolar supply range accommodates dual-rail analog circuitry. Its electronic switching avoids relay-contact bounce and mechanical wear, supporting repeated automated path selection. Designers must verify the maximum signal amplitude, bandwidth, off leakage, and distortion-related charge injection before using the switch in precision audio paths.
پیشنهادی
Sample-and-Hold Acquisition Networks
The DG212DJ+ can implement disconnect and reconnect functions around a sample-and-hold input because each normally open SPST channel provides an explicit open state. The four channels can support hold paths, reset paths, or multiple acquisition inputs when the selected source impedance remains sufficiently high. The 175 ohm on resistance must be included in the settling-time calculation, while switch capacitance and charge injection affect dynamic acquisition accuracy. Use the DG212 data sheet to establish the actual timing and transient limits before defining the sampling interval.
پیشنهادی
Laboratory Automation and Remote Control
The DG212DJ+ supports laboratory automation systems that switch external analog fixtures under firmware control. Four integrated switch channels reduce component count, and CMOS-compatible control permits direct interfacing with common control logic levels. The package uses through-hole leads, which can be advantageous for manually wired prototypes or systems assembled around DIP interconnects. Because the device is rated for bipolar supplies up to ±18 V, it can support compatible positive and negative fixture signals. Check input limits and off-state isolation to avoid loading sensitive sources.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای DG212DJ+ — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | DG212CJ-2 | DG212CJ+ | DG212BDJ |
|---|---|---|---|---|
| Brand | Analog Devices | Maxim Integrated | Maxim Integrated | Vishay Intertechnology |
| Package | 16-pin PDIP | 16-pin PDIP - same | 16-pin PDIP - same | 16-pin PDIP - same |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 1:1 SPST | SPST | SPST | SPST |
| Normal Switch State | Normally open | Normally open | Normally open | Normally open |
تفاوتهای کلیدی
- Four independent analog switches in one DIP package (در مقابلDG419DY+)
- Documented complete DIP replacement option (در مقابلDG212CJ-2)
- Clear identification of a lower-resistance Vishay option (در مقابلDG212BDJ)
یادداشتهای طراحی
Include the DG212DJ+ on resistance in the complete source-impedance calculation. The stated path resistance is 175 ohm, so a 1 kohm receiver plus a 100 ohm upstream source can attenuate the transferred voltage even though the switch is electrically closed. Use the manufacturer data sheet to add switch capacitance and off-state leakage to the settling and acquisition-error analysis, particularly for high-impedance sensor nodes.
Design the positive and negative rails for the full ±4.5 V to ±18 V operating range and decouple each supply close to the device. Keep analog input and output traces away from switching supply nodes, and route control signals separately from sensitive paths. The DG212 family is designed to avoid latch-up when power is removed with signals connected, but that protection does not replace verification of signal amplitudes and supply operating limits.
Use the 16-pin PDIP land pattern and follow the manufacturer pin-description table when assigning tracks. The four switch paths are independent, so avoid unnecessary shared copper between channels that could increase coupling or reduce isolation. Provide adequate clearance around input, output, and control pins, and use a common quiet ground strategy for analog routing to minimize switching transients reaching the source circuit.
Do not substitute the DG212 for the DG202 without checking control polarity. The DG212 has inverted control relative to the DG202, and swapping these families can reverse every channel's commanded state. Also verify the exact ordering suffix, temperature grade, and package variant when using a DG212-family replacement, since family membership alone does not guarantee identical production limits.
اطلاعات انطباق
The DG212DJ+ is identified as lead free and RoHS compliant. Reach, halogen-free status, and conflict-minerals status are not stated.