DG384ACJ - Dual CMOS Analog Switch, 15V | Maxim Integrated
MPN: DG384ACJ ✓ 啟用中DG384ACJ 概覽
A general-purpose CMOS analog switch is an integrated semiconductor device that connects or disconnects an analog signal path under digital control. Unlike a mechanical relay, a solid-state analog switch changes state rapidly without mechanical wear. Within the broader semiconductor hierarchy, analog switches belong to interface ICs and support the signal-path functions required by measurement, communication, industrial-control, and mixed-signal systems.
The DG384ACJ uses an integrated 16-pin DIP package and is specified as a dual analog switch with a 15V maximum voltage. A reported on-resistance of 50 ohms makes it relevant to designs where the switch resistance is acceptable relative to the input impedance and signal amplitude. The CMOS implementation also supports low-power operation when the application does not require continuously switching the analog path.
The DG384ACJ can be used to select one of two signal sources, connect an instrumentation node to a measurement circuit, or provide controlled isolation between circuit sections. Because the on-resistance contributes to channel loss and can introduce distortion with high-frequency signals, the surrounding amplifier and source impedances must be considered carefully. The device is also intended for positive supply operation, based on its 15V rating.
Typical uses include automated test equipment, data-acquisition systems, analog signal selectors, laboratory instruments, industrial controllers, and communication-interface boards. In these systems, the switch can reduce the number of external relays or mechanical contacts while providing faster operation and compact PCB placement.
Layout should keep the analog input and output traces short, provide a low-impedance return path, and place the device close to the switched node. Supply bypassing and protection should follow the circuit conditions present at each analog pin. This product page combines the documented device characteristics with practical guidance for footprint reuse, signal-path planning, procurement, and drop-in replacement assessment.
直接替換替代品,適用於 DG384ACJ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品DG384ACJ 最大額定值與電氣特性
| Device Type | Dual general-purpose CMOS analog switch |
| Switch Configuration | Dual analog switch |
| Maximum Voltage | 15 V |
| On Resistance | 50 ohm |
| Package Type | 16-pin DIP |
| 腳位數 | 16 pins |
| 安裝類型 | Through-hole |
| Technology | CMOS |
| Signal Type | Analog |
| RoHS 狀態 | Non-compliant |
DG384ACJ 16-pin dip 腳位配置指南
DG384ACJ(16-pin dip 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: DG384ACJ.
請參閱 資料表 以查看完整腳位配置。
典型應用
DG384ACJ 適用於 6 應用s: Automated Test Equipment Signal Routing, Data Acquisition Multiplexing, Industrial Control Signal Selection, Laboratory Instrument Signal Selection, Analog Sensor Interface, Communication Interface Signal Routing.
Automated Test Equipment Signal Routing
The DG384ACJ can route a selected analog test signal to an instrumentation channel when the source impedance is compatible with its 50-ohm on-resistance. Its dual-switch arrangement allows two measurement paths to be selected without repeatedly changing external connections. The 16-pin DIP package is useful in legacy test systems designed around through-hole analog boards. Designers should verify control polarity, switching time, and off-state isolation against the required measurement accuracy before using the switch close to the precision measurement front end.
推薦
Data Acquisition Multiplexing
The DG384ACJ can connect one of two analog inputs to a data-acquisition front end, reducing the number of mechanical contacts in a repeated measurement system. A 50-ohm channel resistance is acceptable when the source impedance is substantially higher or when the downstream amplifier can compensate for signal loss. The design should keep the switched trace short and compare the leakage and isolation specifications with the required accuracy of the acquisition channel.
推薦
Industrial Control Signal Selection
The DG384ACJ can select between two command, feedback, or sensor lines in an industrial controller while avoiding the wear and delay of a mechanical relay. Its dual CMOS switch format and 16-pin DIP package are convenient for retrofitting through-hole control boards. Because industrial environments can experience transients and ground-potential differences, engineers should add suitable input protection, maintain a common reference where required, and verify the operating-temperature range for the selected ordering variant.
推薦
Laboratory Instrument Signal Selection
The DG384ACJ can route a calibration or test signal to the correct front-end section of a laboratory instrument while keeping the implementation compact. The 50-ohm on-resistance must be included in the overall signal-path calculation, particularly for low-amplitude sources and impedance-sensitive sensors. A low-noise grounding strategy, short analog traces, and adequate bypassing help prevent the switch and its supply network from degrading measurement precision.
推薦
Analog Sensor Interface
The DG384ACJ can switch a sensor signal between a measurement amplifier and an alternative processing path, allowing a compact interface to support more than one measurement function. Its suitability depends on source impedance, signal level, and the allowable insertion loss created by the 50-ohm on-resistance. For resistive sensors, calculate the divider ratio formed by the switch resistance and the amplifier input resistance, and confirm that control transitions do not create unacceptable settling behavior.
推薦
Communication Interface Signal Routing
The DG384ACJ can route low-frequency analog or control signals in communication-interface equipment when the circuit uses a 16-pin DIP layout. The solid-state dual switch provides a practical alternative to mechanical contactors in auxiliary signaling paths. Signal integrity must be evaluated with the actual source and termination impedances because the stated 50-ohm on-resistance can alter amplitude and edge behavior. Decoupling, grounding, and protection should be placed close to the relevant device pins.
推薦
推薦產品摘要
工程參考資料,適用於 DG384ACJ — 比較、設計指引及合規資訊。
選型指南
主要差異化特點
- Legacy-compatible 16-pin DIP implementation (對比Surface-mount analog switch)
- Documented 50-ohm on-resistance (對比Low-resistance precision analog switch)
- Dual general-purpose switching (對比Single analog switch)
設計說明
Include the 50-ohm on-resistance in the complete source-to-load network calculation. It forms a divider with the source impedance and the receiver or amplifier input resistance. For low-amplitude signals, use a high-impedance amplifier and keep the routed trace short. Verify the off-state isolation and leakage requirements before using the switch near a precision measurement node.
The DG384ACJ uses a 16-pin DIP footprint, so mechanical replacement requires the same lead spacing, row spacing, and drill pattern. Confirm the package drawing and pin-1 orientation before assembly. Keep analog input and output traces away from fast digital switching nodes, and provide a continuous ground reference to reduce coupling into the switched signal.
Route supply and ground connections directly to the device with short traces and place the recommended bypass capacitor near the power pins. Keep the switched-node copper compact to minimize parasitic capacitance and susceptibility to induced noise. If any connected source can exceed the 15V maximum rating during startup or fault conditions, add suitable clamping or series resistance before the DG384ACJ pins.
Do not select a replacement solely because its family name or package count matches. Compare control polarity, analog pin assignment, supply limits, on-resistance, switching time, and operating-temperature grade. A same-family ordering suffix can change the environmental grade or qualification without changing the basic function, so each candidate must be checked against the manufacturer pin and ordering tables.
合規資訊
The device is listed as RoHS non-compliant. No additional compliance status should be assumed without current manufacturer documentation.