DS90C031TM/NOPB - 155.5 Mbps Quad LVDS Driver | Texas Instruments
MPN: DS90C031TM/NOPB ✓ 啟用中DS90C031TM/NOPB 概覽
An LVDS differential line driver is an interface circuit that converts single-ended logic signals into two complementary, low-voltage differential outputs. The differential signaling architecture belongs to the broader low-voltage digital interface and interface IC hierarchy. By conveying the same logical information over two conductors, LVDS helps reduce common-mode noise sensitivity and supports high-speed data transfer over balanced interconnects.
Four independently controlled transmitters provide substantial channel density for point-to-point links, backplanes, industrial data acquisition, video processing, and other multi-channel systems. The manufacturer describes the device for ultra-low power dissipation and high data rates. Its CMOS input stage accepts TTL/CMOS-compatible signals, allowing it to interface with conventional digital logic without a separate input-level translation stage.
The DS90C031 translates each CMOS input into a low-voltage differential output of approximately 350 mV. Four channels in one package reduce the component count compared with separate single-channel drivers, while the 16-pin SOIC package supports conventional surface-mount assembly. The specified signaling capability exceeds 155.5 Mbps per channel, making it suitable for clock distribution, parallel-to-serial data transmission, and other links requiring low-power differential signaling.
Typical uses include video-processing links, data-conversion systems, instrumentation, industrial control, communications equipment, and point-to-point LVDS interconnects. In these applications, the four-channel arrangement allows several data paths to be synchronized or routed through one device. The actual usable link rate depends on the complete system, including source timing, cable characteristics, receiver performance, termination, trace geometry, and signal-integrity margins.
PCB implementation should preserve the differential nature of the LVDS pair. Route each differential pair as a tightly coupled pair with symmetrical geometry, minimize stubs, and avoid discontinuities that create reflected signals. Place any receiver-side termination close to the receiving device. Decoupling and power-distribution design must also support four switching channels without introducing excessive supply noise onto the differential outputs.
This page organizes the manufacturer’s functional and rate information around practical selection, package, replacement, and signal-integrity questions. It also distinguishes the target ordering code from related manufacturer catalog entries and identifies when a pin-compatible substitute still requires independent verification of operating limits, enable or control behavior, supply voltage, and output timing.
直接替換替代品,適用於 DS90C031TM/NOPB — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: DS90C031TM/NOPB (相同外形與佔位) — 差異在於 Maximum Data Rate, Operating Temperature Range, Number of Drivers, Package.
DS90C031TM/NOPB
✅ 直接替換聯絡詢價
查看資料表 →DS90C031TMX/NOPB
✅ 直接替換聯絡詢價
查看資料表 →DS90C031BTM/NOPB
✅ 直接替換聯絡詢價
查看資料表 →DS90C031TM
✅ 直接替換聯絡詢價
查看資料表 →DS90C031TM/NOPB 規格
| Product Type | Quad CMOS differential line driver |
| Number of Drivers | 4 |
| Supported Protocol | LVDS |
| Input Logic Compatibility | TTL/CMOS |
| Maximum Data Rate | In excess of 155.5 Mbps |
| Equivalent Clock Frequency | 77.7 MHz |
| Differential Output Voltage | Approximately 350 mV |
| 供應電壓 | 5 V |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | SOIC (D), 16 pins |
| 安裝類型 | Surface mount |
| 輸出配置 | 4 differential LVDS outputs |
| Input Configuration | 4 single-ended CMOS/TTL inputs |
| Lead-Free Ordering Code | DS90C031TM/NOPB |
DS90C031TM/NOPB soic (d), 16 pins 腳位配置指南
DS90C031TM/NOPB(soic (d), 16 pins 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: DS90C031TM/NOPB.
請參閱 資料表 以查看完整腳位配置。
典型應用
DS90C031TM/NOPB 適用於 6 應用s: High-Speed Video Processing Links, Industrial Data Acquisition, Clock Distribution, Point-to-Point Communications, Precision Test and Measurement, Power and Control Interfaces.
High-Speed Video Processing Links
The DS90C031TM/NOPB fits parallel-to-serial video and control paths requiring up to four differential outputs. Each channel converts a TTL/CMOS input into an approximately 350 mV LVDS differential signal at rates in excess of 155.5 Mbps, or 77.7 MHz. Using four drivers in one 16-pin SOIC reduces the number of separate line-driver packages. The implementation must keep each output pair closely coupled, provide a continuous return path, and account for receiver and cable bandwidth when establishing the video transport standard.
Industrial Data Acquisition
The DS90C031TM/NOPB can drive several low-power differential links between an acquisition or control board and remote instrumentation. Four independently driven channels provide a practical way to transport clock, trigger, or sampled-data signals while rejecting common-mode noise through differential signaling. The documented rate above 155.5 Mbps leaves substantial link margin for short industrial backplanes or shielded cables. Signal integrity still depends on a controlled return path, correct receiver termination, and a connector or cable whose loss is acceptable at the operating frequency.
Clock Distribution
The DS90C031TM/NOPB is suitable for distributing one or more high-speed clocks through low-power LVDS pairs. Four channels allow a source to fan out as many as four differential clock signals, and the 77.7 MHz equivalent rate supports substantially higher data rates than a conventional single-ended clock. In a backplane, tightly coupled traces and continuous ground references are essential for minimizing edge distortion and reflections. Receiver thresholds and clock jitter should be evaluated together because low output amplitude alone does not guarantee complete end-to-end timing margin.
Point-to-Point Communications
The DS90C031TM/NOPB supports point-to-point communications links that require multiple CMOS-to-differential channels in a compact package. Its four transmitters can carry separate commands, status signals, or low-speed payload lanes alongside faster synchronous traffic. The LVDS output is approximately 350 mV, while the input side accepts TTL/CMOS-compatible levels. Cable length, connector geometry, receiver capabilities, and electromagnetic-emissions requirements determine whether the complete link is practical, so the interface should be validated as a system rather than judged from the driver rating alone.
Precision Test and Measurement
The DS90C031TM/NOPB can provide low-power differential drive for test and measurement modules that transfer clocks, triggers, or control information between circuit boards. Supporting rates above 155.5 Mbps allows the driver to feed contemporary acquisition and modular instrument architectures while limiting bus loading compared with unsuitable long single-ended routes. Accurate results depend on controlled impedance, short differential stubs, receiver termination, and separation from sensitive analog nodes. Differential routing can reduce susceptibility to common-mode interference, but it does not replace grounding or shielding practices.
Power and Control Interfaces
The DS90C031TM/NOPB is useful when several low-voltage control paths must cross a board or backplane boundary with less susceptibility to common-mode noise. Four CMOS inputs become four approximately 350 mV differential outputs, enabling a compact bridge between control logic and remote circuitry. Designers should use the 5 V operating supply identified for the related catalog entries, maintain a low-impedance return path, and avoid adding long stubs to the differential pairs. Receiver enable, bus-direction, and fault-handling requirements must be satisfied elsewhere in the interface architecture.
工程參考資料,適用於 DS90C031TM/NOPB — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | DS90C031TM/NOPB | DS90C031TMX/NOPB | DS90C031BTM/NOPB | DS90C031TM |
|---|---|---|---|---|---|
| Package | SOIC (D), 16 pins | SOIC (D), 16 pins | SOIC (D), 16 pins | SOIC (D), 16 pins | SOIC (D), 16 pins |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Function | Quad CMOS differential line driver | Quad CMOS differential line driver | Quad CMOS differential line driver | LVDS driver | Quad CMOS differential line driver |
| Number of Transmitters | 4 | 4 | 4 | 4 | 4 |
| Number of Receivers | 0 | 0 | 0 | 0 | 0 |
| Signaling Rate | In excess of 155.5 Mbps | In excess of 155.5 Mbps | In excess of 155.5 Mbps | 155.5 Mbps | In excess of 155.5 Mbps |
| Equivalent Clock Rate | 77.7 MHz | 77.7 MHz | 77.7 MHz | 77.75 MHz | 77.7 MHz |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Input Signal | TTL/CMOS | TTL/CMOS | TTL/CMOS | CMOS/TTL | TTL/CMOS |
| Output Protocol | LVDS | LVDS | LVDS | LVDS | LVDS |
主要差異化特點
- Four differential outputs in one 16-pin package (對比DS90C031BTM/NOPB)
- High-rate four-channel LVDS integration (對比DS90C031TM)
- Direct TTL/CMOS input interface (對比DS90C031TMX/NOPB)
設計說明
Route each LVDS output as a tightly coupled differential pair with symmetrical geometry and a continuous reference plane beneath the pair. Keep input and output traces away from clocks, switching-power nodes, and high-current return paths. The DS90C031TM/NOPB can operate above 155.5 Mbps, so even small mismatches in trace length or geometry can degrade eye opening or create reflections.
Place the receiver termination as close as practical to the receiving device and determine its value from the receiver and cable system rather than from the driver alone. Avoid stubs and test pads on high-speed differential nets. Validate the complete DS90C031TM/NOPB link for differential impedance, common-mode behavior, jitter, and cable loss because the 155.5 Mbps device rating does not define the achievable performance of a particular board or cable.
Use a low-impedance 5 V supply plane and place the device’s decoupling capacitor close to the supply and ground pins. Four simultaneously switching LVDS channels can produce fast edge currents even though the device is designed for low power dissipation. Keep the return-current path beneath the signal pair and verify supply ripple at the device during full-channel activity; unusually low current alone does not ensure a quiet output rail.
合規資訊
The /NOPB ordering suffix identifies the lead-free catalog option, but no separate explicit RoHS, REACH, halogen-free, or conflict-minerals statement appears in the manufacturer information provided. AEC-Q100 qualification is not indicated for this interface device.