Texas Instruments

DS90C031TM/NOPB - 155.5 Mbps Quad LVDS Driver | Texas Instruments

MPN: DS90C031TM/NOPB ✓ نشط
Approximately 350 mV Vdss SOIC (D), 16 pins Package 77.7 MHz Speed
الحد الأدنى للطلب: 1 |

DS90C031TM/NOPB نظرة عامة

Texas Instruments DS90C031TM/NOPB is a four-channel CMOS differential line driver designed for low-power LVDS transmission at data rates in excess of 155.5 Mbps, equivalent to a 77.7 MHz clock rate. The device accepts TTL/CMOS inputs and translates them into approximately 350 mV differential LVDS outputs. It is packaged in a 16-pin SOIC (D) package.

An LVDS differential line driver is an interface circuit that converts single-ended logic signals into two complementary, low-voltage differential outputs. The differential signaling architecture belongs to the broader low-voltage digital interface and interface IC hierarchy. By conveying the same logical information over two conductors, LVDS helps reduce common-mode noise sensitivity and supports high-speed data transfer over balanced interconnects.

Four independently controlled transmitters provide substantial channel density for point-to-point links, backplanes, industrial data acquisition, video processing, and other multi-channel systems. The manufacturer describes the device for ultra-low power dissipation and high data rates. Its CMOS input stage accepts TTL/CMOS-compatible signals, allowing it to interface with conventional digital logic without a separate input-level translation stage.

The DS90C031 translates each CMOS input into a low-voltage differential output of approximately 350 mV. Four channels in one package reduce the component count compared with separate single-channel drivers, while the 16-pin SOIC package supports conventional surface-mount assembly. The specified signaling capability exceeds 155.5 Mbps per channel, making it suitable for clock distribution, parallel-to-serial data transmission, and other links requiring low-power differential signaling.

Typical uses include video-processing links, data-conversion systems, instrumentation, industrial control, communications equipment, and point-to-point LVDS interconnects. In these applications, the four-channel arrangement allows several data paths to be synchronized or routed through one device. The actual usable link rate depends on the complete system, including source timing, cable characteristics, receiver performance, termination, trace geometry, and signal-integrity margins.

PCB implementation should preserve the differential nature of the LVDS pair. Route each differential pair as a tightly coupled pair with symmetrical geometry, minimize stubs, and avoid discontinuities that create reflected signals. Place any receiver-side termination close to the receiving device. Decoupling and power-distribution design must also support four switching channels without introducing excessive supply noise onto the differential outputs.

This page organizes the manufacturer’s functional and rate information around practical selection, package, replacement, and signal-integrity questions. It also distinguishes the target ordering code from related manufacturer catalog entries and identifies when a pin-compatible substitute still requires independent verification of operating limits, enable or control behavior, supply voltage, and output timing.

بدائل مباشرة لـ DS90C031TM/NOPB — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع DS90C031TM/NOPB (نفس عامل الشكل والبصمة) — يختلف في Maximum Data Rate, Operating Temperature Range, Number of Drivers, Package.

Texas Instruments
Maximum Data Rate: 155.5 Mbps minimum supported rate
Operating Temperature Range: -40°C to 85°C
Number of Drivers: 4 channels
Texas Instruments
Maximum Data Rate: Greater than 155.5 Mbps
Operating Temperature Range: -55°C to +125°C

DS90C031TM/NOPB

✅ بديل مباشر
Texas Instruments
📦 SOIC (D), 16 pins
Quad CMOS differential line driver · 4 · LVDS · TTL/CMOS · In excess of 155.5 Mbps · 77.7 MHz · Approximately 350 mV · 5 V

تواصل لمعرفة السعر

عرض ورقة البيانات ←

DS90C031TMX/NOPB

✅ بديل مباشر
Texas Instruments
📦 SOIC (D), 16 pins
Quad CMOS differential line driver · 4 channels · TTL/CMOS · LVDS, 350 mV differential output · Greater than 155.5 Mbps · 77.7 MHz · 4.5 V to 5.5 V · -40 °C to +85 °C

تواصل لمعرفة السعر

عرض ورقة البيانات ←

DS90C031BTM/NOPB

✅ بديل مباشر
Texas Instruments
📦 SOIC (D), 16 pins
Quad CMOS differential line driver · 4 channels · Low Voltage Differential Signaling (LVDS) · 155.5 Mbps · 77.7 MHz · 4.5 V to 5.5 V · 21 mA · 350 mV

تواصل لمعرفة السعر

عرض ورقة البيانات ←

DS90C031TM

✅ بديل مباشر
Texas Instruments
📦 SOIC (D), 16 pins
Quad CMOS differential line driver · CMOS · LVDS · 4 · Greater than 155.5 Mbps · Greater than 77.7 MHz · 5 V · TTL/CMOS

تواصل لمعرفة السعر

عرض ورقة البيانات ←

DS90C031TM/NOPB المواصفات

Product Type Quad CMOS differential line driver
Number of Drivers 4
Supported Protocol LVDS
Input Logic Compatibility TTL/CMOS
Maximum Data Rate In excess of 155.5 Mbps
Equivalent Clock Frequency 77.7 MHz
Differential Output Voltage Approximately 350 mV
جهد التغذية 5 V
نطاق درجة حرارة التشغيل -40 °C to +85 °C
العلبة SOIC (D), 16 pins
نوع التركيب Surface mount
تكوين الخرج 4 differential LVDS outputs
Input Configuration 4 single-ended CMOS/TTL inputs
Lead-Free Ordering Code DS90C031TM/NOPB

دليل تكوين أطراف DS90C031TM/NOPB soic (d), 16 pins

تكوين الأطراف لـ DS90C031TM/NOPB (حزمة soic (d), 16 pins). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة soic (d), 16 pins لـ DS90C031TM/NOPB

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ DS90C031TM/NOPB.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

DS90C031TM/NOPB مناسب لـ 6 التطبيقs: High-Speed Video Processing Links, Industrial Data Acquisition, Clock Distribution, Point-to-Point Communications, Precision Test and Measurement, Power and Control Interfaces.

📺

High-Speed Video Processing Links

The DS90C031TM/NOPB fits parallel-to-serial video and control paths requiring up to four differential outputs. Each channel converts a TTL/CMOS input into an approximately 350 mV LVDS differential signal at rates in excess of 155.5 Mbps, or 77.7 MHz. Using four drivers in one 16-pin SOIC reduces the number of separate line-driver packages. The implementation must keep each output pair closely coupled, provide a continuous return path, and account for receiver and cable bandwidth when establishing the video transport standard.

🏭

Industrial Data Acquisition

The DS90C031TM/NOPB can drive several low-power differential links between an acquisition or control board and remote instrumentation. Four independently driven channels provide a practical way to transport clock, trigger, or sampled-data signals while rejecting common-mode noise through differential signaling. The documented rate above 155.5 Mbps leaves substantial link margin for short industrial backplanes or shielded cables. Signal integrity still depends on a controlled return path, correct receiver termination, and a connector or cable whose loss is acceptable at the operating frequency.

🖥️

Clock Distribution

The DS90C031TM/NOPB is suitable for distributing one or more high-speed clocks through low-power LVDS pairs. Four channels allow a source to fan out as many as four differential clock signals, and the 77.7 MHz equivalent rate supports substantially higher data rates than a conventional single-ended clock. In a backplane, tightly coupled traces and continuous ground references are essential for minimizing edge distortion and reflections. Receiver thresholds and clock jitter should be evaluated together because low output amplitude alone does not guarantee complete end-to-end timing margin.

🌐

Point-to-Point Communications

The DS90C031TM/NOPB supports point-to-point communications links that require multiple CMOS-to-differential channels in a compact package. Its four transmitters can carry separate commands, status signals, or low-speed payload lanes alongside faster synchronous traffic. The LVDS output is approximately 350 mV, while the input side accepts TTL/CMOS-compatible levels. Cable length, connector geometry, receiver capabilities, and electromagnetic-emissions requirements determine whether the complete link is practical, so the interface should be validated as a system rather than judged from the driver rating alone.

🔧

Precision Test and Measurement

The DS90C031TM/NOPB can provide low-power differential drive for test and measurement modules that transfer clocks, triggers, or control information between circuit boards. Supporting rates above 155.5 Mbps allows the driver to feed contemporary acquisition and modular instrument architectures while limiting bus loading compared with unsuitable long single-ended routes. Accurate results depend on controlled impedance, short differential stubs, receiver termination, and separation from sensitive analog nodes. Differential routing can reduce susceptibility to common-mode interference, but it does not replace grounding or shielding practices.

⚡

Power and Control Interfaces

The DS90C031TM/NOPB is useful when several low-voltage control paths must cross a board or backplane boundary with less susceptibility to common-mode noise. Four CMOS inputs become four approximately 350 mV differential outputs, enabling a compact bridge between control logic and remote circuitry. Designers should use the 5 V operating supply identified for the related catalog entries, maintain a low-impedance return path, and avoid adding long stubs to the differential pairs. Receiver enable, bus-direction, and fault-handling requirements must be satisfied elsewhere in the interface architecture.

What is the DS90C031TM/NOPB?
The DS90C031TM/NOPB is a four-channel CMOS differential line driver from Texas Instruments. It accepts TTL/CMOS input signals and converts them into approximately 350 mV differential LVDS outputs. According to the manufacturer product page, the device is intended for low power dissipation and data rates in excess of 155.5 Mbps, or 77.7 MHz, and is offered in a 16-pin SOIC (D) package.
How many LVDS output channels does DS90C031TM/NOPB provide?
The DS90C031TM/NOPB provides four differential LVDS output channels and no receiver channels. The manufacturer describes it as a quad CMOS differential line driver, with a corresponding CMOS input for each differential output. This four-channel arrangement reduces board area and component count in systems that need several point-to-point LVDS links.
What is the maximum data rate of DS90C031TM/NOPB?
The DS90C031TM/NOPB supports data rates in excess of 155.5 Mbps, corresponding to 77.7 MHz. According to the Texas Instruments product description and manufacturer datasheet, the four CMOS differential drivers use LVDS signaling to achieve this rate while keeping power dissipation low. The complete system must also satisfy receiver, cable, termination, and timing requirements.
What package does DS90C031TM/NOPB use?
The DS90C031TM/NOPB uses a 16-pin SOIC (D) surface-mount package. The Texas Instruments part-details page identifies the package as SOIC (D) with 16 pins, and the manufacturer datasheet describes the DS90C031 as a quad differential line driver. Use the pin-description table in the manufacturer datasheet when assigning PCB nets.
Where can I download the DS90C031TM/NOPB datasheet PDF?
The official DS90C031 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ds90c031.pdf. It contains the device description, electrical characteristics, package information, and application details for the DS90C031 family. The manufacturer’s DS90C031 product page is also available at https://www.ti.com/product/DS90C031.
Where can I find the DS90C031TM/NOPB pinout?
The DS90C031TM/NOPB pinout is documented in the pin-configuration section of the official Texas Instruments DS90C031 datasheet. The exact ordering code uses a 16-pin SOIC (D) package, so its numbered footprint corresponds to a 16-pin SOIC. Use the datasheet pin table and package drawing when assigning inputs, differential outputs, power, and ground connections.
What input logic levels does DS90C031TM/NOPB accept?
The DS90C031TM/NOPB accepts TTL/CMOS input levels and translates them into low-voltage differential outputs. According to the Texas Instruments product description, the output amplitude is approximately 350 mV. The input thresholds, supply range, and timing limits should be taken from the electrical-characteristics table in the manufacturer datasheet rather than inferred from the generic TTL label.
Where can I buy DS90C031TM/NOPB and check its current price?
The current commercial status and unit price for DS90C031TM/NOPB should be requested through the Request a Quote form on this page. The form is the appropriate route for checking available order quantities, packaging, and lead time because commercial availability can change independently of the device’s technical specification. Confirm the exact 16-pin SOIC ordering code before requesting a quotation.
What is the lead time for DS90C031TM/NOPB?
The current lead time for DS90C031TM/NOPB should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, date, inventory position, and selected delivery method. For an engineering design, use the manufacturer’s stated 5 V operating supply and confirm electrical and timing requirements against the DS90C031 datasheet before committing the part to a schedule.
Is DS90C031TM/NOPB in stock?
Current DS90C031TM/NOPB stock should be checked through the Request a Quote form on this page rather than through a static availability statement. Inventory status is transactional and can change without a change in the component’s lifecycle status. When requesting availability, specify the quantity, required delivery date, and whether the 16-pin SOIC (D) package is acceptable.
DS90C031TM/NOPB vs DS90C031TMX/NOPB: which is the better drop-in choice?
DS90C031TM/NOPB and DS90C031TMX/NOPB both describe Texas Instruments four-channel LVDS drivers in the 16-pin SOIC (D) package, with the same stated 5 V supply, TTL/CMOS input compatibility, and 155.5 Mbps signaling capability. Their ordering suffixes represent catalog distinctions rather than different functional ratings. Choose the exact suffix required by your approved BOM, procurement system, and manufacturer part-detail listing.
Can DS90C031BTM/NOPB replace DS90C031TM/NOPB?
DS90C031BTM/NOPB is a closely related Texas Instruments catalog entry with the same 16-SOIC format, four transmitters, zero receivers, 5 V supply, TTL/CMOS input type, and 155.5 Mbps signaling rate according to the manufacturer comparison information. Verify the complete ordering-code and device-status details on the manufacturer product page before substitution. PCB compatibility alone does not replace a formal part-number approval.
What is the best drop-in replacement for DS90C031TM/NOPB?
The closest verified drop-in choices are related Texas Instruments DS90C031 catalog entries, including DS90C031TM, DS90C031TMX/NOPB, and DS90C031BTM/NOPB. They share the 16-pin SOIC format and core four-channel LVDS-driver characteristics, but each may represent a different orderable suffix or temperature classification. The manufacturer datasheet and product-status information should be checked before approving a replacement.
When should I choose DS90C031TM/NOPB over another quad LVDS driver?
Choose DS90C031TM/NOPB when the design requires four CMOS-to-LVDS differential outputs, support for data rates above 155.5 Mbps, TTL/CMOS-compatible inputs, and a 16-pin SOIC footprint. If another candidate offers different supply limits, output-enable controls, fail-safe behavior, or a different package, verify those functions rather than assuming interchangeability. The DS90C031 is best suited to designs centered on its documented four-channel driver architecture.
Is DS90C031TM/NOPB suitable for high-speed video or instrumentation links?
The DS90C031TM/NOPB is suitable for low-power, high-rate LVDS links whose design fits a four-channel CMOS differential driver. Its documented capability exceeds 155.5 Mbps, making it applicable to video processing, clock distribution, data acquisition, and point-to-point communications. The usable bandwidth of a finished cable link still depends on receiver performance, termination, trace geometry, media, and the system’s jitter and timing budget.

بيانات مرجعية هندسية لـ DS90C031TM/NOPB — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose DS90C031TM/NOPB when a design requires four TTL/CMOS-to-LVDS differential outputs, operation above 155.5 Mbps, low-power signaling, and a 16-pin SOIC footprint. The related DS90C031TMX/NOPB, DS90C031BTM/NOPB, and DS90C031TM entries are the closest catalog-level alternatives because they share the quad-driver function and 16-pin SOIC format. Their suffixes and classification can affect ordering, temperature coverage, or lifecycle treatment, so the exact device status and ordering code must be confirmed before substitution. Do not select a generic quad-LVDS driver solely by package count: power range, propagation delay, output-enable logic, input thresholds, receiver compatibility, and fail-safe behavior may differ. For the target, emphasize the manufacturer’s four-channel, 5 V, approximately 350 mV output and greater-than-155.5 Mbps capabilities, then validate PCB routing and the complete receiver-and-cable channel.

المقارنة مع البدائل

المعامل هذا المنتج DS90C031TM/NOPB DS90C031TMX/NOPB DS90C031BTM/NOPB DS90C031TM
Package SOIC (D), 16 pins SOIC (D), 16 pins SOIC (D), 16 pins SOIC (D), 16 pins SOIC (D), 16 pins
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Function Quad CMOS differential line driver Quad CMOS differential line driver Quad CMOS differential line driver LVDS driver Quad CMOS differential line driver
Number of Transmitters 4 4 4 4 4
Number of Receivers 0 0 0 0 0
Signaling Rate In excess of 155.5 Mbps In excess of 155.5 Mbps In excess of 155.5 Mbps 155.5 Mbps In excess of 155.5 Mbps
Equivalent Clock Rate 77.7 MHz 77.7 MHz 77.7 MHz 77.75 MHz 77.7 MHz
Supply Voltage 5 V 5 V 5 V 5 V 5 V
Input Signal TTL/CMOS TTL/CMOS TTL/CMOS CMOS/TTL TTL/CMOS
Output Protocol LVDS LVDS LVDS LVDS LVDS

أبرز الفروقات

  • Four differential outputs in one 16-pin package (مقابلDS90C031BTM/NOPB)
  • High-rate four-channel LVDS integration (مقابلDS90C031TM)
  • Direct TTL/CMOS input interface (مقابلDS90C031TMX/NOPB)

ملاحظات التصميم

Route each LVDS output as a tightly coupled differential pair with symmetrical geometry and a continuous reference plane beneath the pair. Keep input and output traces away from clocks, switching-power nodes, and high-current return paths. The DS90C031TM/NOPB can operate above 155.5 Mbps, so even small mismatches in trace length or geometry can degrade eye opening or create reflections.

Place the receiver termination as close as practical to the receiving device and determine its value from the receiver and cable system rather than from the driver alone. Avoid stubs and test pads on high-speed differential nets. Validate the complete DS90C031TM/NOPB link for differential impedance, common-mode behavior, jitter, and cable loss because the 155.5 Mbps device rating does not define the achievable performance of a particular board or cable.

Use a low-impedance 5 V supply plane and place the device’s decoupling capacitor close to the supply and ground pins. Four simultaneously switching LVDS channels can produce fast edge currents even though the device is designed for low power dissipation. Keep the return-current path beneath the signal pair and verify supply ripple at the device during full-channel activity; unusually low current alone does not ensure a quiet output rail.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The /NOPB ordering suffix identifies the lead-free catalog option, but no separate explicit RoHS, REACH, halogen-free, or conflict-minerals statement appears in the manufacturer information provided. AEC-Q100 qualification is not indicated for this interface device.

تم التحقق من البيانات في: 2026-11-16 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

ds90c031tm nopb DS90C031TM/NOPB datasheet DS90C031TM/NOPB datasheet pdf DS90C031TM/NOPB pinout DS90C031TM/NOPB equivalent DS90C031TM/NOPB replacement DS90C031TM/NOPB vs DS90C031BTM/NOPB DS90C031TM/NOPB price DS90C031TM/NOPB stock Texas Instruments DS90C031TM/NOPB DS90C031 155.5 Mbps LVDS driver DS90C031 16-SOIC pinout

المكونات والمصطلحات ذات الصلة

Texas Instruments DS90C031TM/NOPB DS90C031TMX/NOPB DS90C031BTM/NOPB DS90C031TM quad CMOS differential line driver LVDS driver Low Voltage Differential Signaling LVDS CMOS TTL differential line driver interface IC line driver semiconductor SOIC-16 QFN family surface mount SMD 155.5 Mbps 77.7 MHz 350 mV differential output 5 V supply industrial data acquisition video processing
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر