Texas Instruments

DS90LT012ATMFX - 3V LVDS Receiver with 100Ω Termination

MPN: DS90LT012ATMFX ✓ 啟用中
3 V Vdss SOT-23-5 Package
MOQ: 1 |

DS90LT012ATMFX 概覽

Texas Instruments DS90LT012ATMFX is a 3-V LVDS single differential line receiver with CMOS output, 350 mV typical differential input sensitivity, and an integrated input termination resistor for point-to-point links. The device is packaged in a 5-pin SOT-23 package. It converts low-voltage differential LVDS signals into 3-V CMOS logic levels while supporting open, shorted, and 100Ω-terminated input fail-safe operation.

An LVDS receiver is an interface IC that detects a small differential voltage across a balanced pair of conductors and converts that signal into a single-ended CMOS output. LVDS belongs to the differential data-interface hierarchy, where low signal amplitude, common-mode rejection, and balanced routing improve signal integrity over longer point-to-point interconnects. The DS90LT012A family combines this receiver function with an onboard termination network intended to simplify point-to-point PCB designs.

Key features include 3-V CMOS output signaling, a typical input threshold of 350 mV, and integrated line termination. The receiver provides a HIGH output during open, shorted, and terminated fail-safe conditions, allowing downstream logic to identify an invalid physical link. Its five-pin SOT-23 package supports compact placement, while the integrated 100Ω termination removes the need for a separate input resistor in a conventional point-to-point LVDS connection.

The DS90LT012A architecture is optimized for receiving differential data from a companion LVDS transmitter over a short point-to-point connection. The receiver translates the differential input into a CMOS output referenced to the receiver supply. Because this is a single receiver rather than a multi-channel transceiver, board designers gain a compact solution for links that require one differential data channel, such as clock distribution, low-speed control links, or isolated command interfaces using compatible LVDS signaling.

Typical uses include LVDS clock-recovery links, point-to-point command and control channels, industrial equipment links, and test systems where a low-amplitude differential receiver is preferred. In a point-to-point circuit, the companion transmitter drives the differential pair and the DS90LT012ATMFX provides a direct CMOS output for the receiving controller or logic device. The integrated termination should be considered during signal-integrity analysis because it loads the transmission line and influences edge behavior.

PCB implementation requires a short, balanced route between the transmitter and receiver, with the differential pair terminated at the receiving end. Place the receiver close to the connector or driver to minimize stub length and reflections, maintain closely matched routing geometry, and connect the supply and ground pins to a low-impedance plane. The manufacturer datasheet should be used for final pin assignments, bypass requirements, and input/output truth tables before layout release.

This product overview combines the manufacturer interface description with practical comparison, application, and layout guidance. It highlights the DS90LT012ATMFX's integrated termination and fail-safe behavior while separating verified electrical facts from parameters that still require confirmation from the complete device documentation or an individual design validation.

直接替換替代品,適用於 DS90LT012ATMFX — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

DS90LT012ATMF

✅ 直接替換
📦 SOT-23-5
Same DS90LT012A receiver function and SOT-23-5 package; ordering suffix differs by 0% in the documented 3-V supply, 350 mV typical input, and 100Ω termination ratings

📋 參考替代品(不在目錄中)

DS90LT012ATMF/NOPB

✅ 直接替換
📦 SOT-23-5
Same DS90LT012A receiver function and SOT-23-5 package; NOPB ordering code differs by 0% in the documented 3-V supply, 350 mV typical input, and 100Ω termination ratings

📋 參考替代品(不在目錄中)

DS90LT012ATMFX/NOPB

✅ 直接替換
📦 SOT-23-5
Same DS90LT012ATMFX receiver function and SOT-23-5 package; NOPB ordering code differs by 0% in the documented 3-V supply, 350 mV typical input, and 100Ω termination ratings

📋 參考替代品(不在目錄中)

DS90LV012ATMF

✅ 直接替換
📦 SOT-23-5
Same 3-V LVDS receiver class and SOT-23-5 package, but omits the DS90LT012A integrated 100Ω input termination, producing a functional termination-network difference

📋 參考替代品(不在目錄中)

DS90LT012ATMFX 規格

Product Type 3-V LVDS single differential line receiver
Receiver Configuration 1 receiver
供應電壓 3 V
Output Logic 3-V CMOS
Typical Differential Input Threshold 350 mV
Integrated Input Termination 100 Ω
Fail-Safe Support Open, shorted, and 100 Ω terminated inputs
Fail-Safe Output State HIGH
封裝 SOT-23-5
Terminal Count 5 terminals
安裝類型 Surface mount
Temperature Grade Industrial
Termination Configuration Integrated for point-to-point applications
Input Type Low-voltage differential input
輸出類型 Single-ended CMOS

DS90LT012ATMFX sot-23-5 腳位配置指南

DS90LT012ATMFX(sot-23-5 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

DS90LT012ATMFX 的 sot-23-5 封裝腳位圖

無詳細腳位定義資料: DS90LT012ATMFX.

請參閱 資料表 以查看完整腳位配置。

典型應用

DS90LT012ATMFX 適用於 6 應用s: Point-to-Point LVDS Clock Link, Industrial Command and Control Interface, LVDS Data Backplane Endpoint, Test and Measurement Instrument Link, Low-Voltage Logic Interconnect, Secure Camera or Sensor Link.

🌐

Point-to-Point LVDS Clock Link

The DS90LT012ATMFX fits a point-to-point clock link because it accepts a 350 mV typical differential LVDS input and converts it to a 3-V CMOS output. Its integrated 100Ω input termination removes the need for a separate receiver-end termination resistor in a conventional point-to-point topology. Place the receiver near the transmitter or connector, preserve a balanced route over a continuous reference plane, and confirm that the companion transmitter can drive the integrated load while maintaining the required edge rate and output amplitude.

🏭

Industrial Command and Control Interface

The DS90LT012ATMFX can convert a compact LVDS command link into a 3-V CMOS signal for an industrial controller, remote I/O module, or equipment-control board. Differential transport reduces sensitivity to common-mode noise relative to single-ended signaling, while the receiver's open, shorted, and 100Ω-terminated fail-safe behavior provides a defined HIGH output when the physical connection is invalid. Firmware can use that stable state to detect a disconnected or malformed link, although the overall protection strategy must fit the system's safety requirements.

🖥️

LVDS Data Backplane Endpoint

The DS90LT012ATMFX is useful at the endpoint of a short differential data connection where a compact receiver and deterministic fail-safe response are required. The 350 mV typical input threshold supports low-amplitude LVDS detection, and the 3-V CMOS output can connect directly to suitable controller logic. Route the pair symmetrically, avoid long stubs, and assess the integrated 100Ω termination against the transmitter drive capability. For wider buses with multiple receivers, an external termination arrangement may be more appropriate.

🔧

Test and Measurement Instrument Link

The DS90LT012ATMFX can serve as the receive element in a compact differential link between instrument electronics and a controller. Its 3-V CMOS output provides a convenient logic-level result, while the integrated 100Ω termination simplifies a dedicated point-to-point route. Keep the receiver away from high-energy switching nodes, preserve controlled return current through the ground plane, and verify the complete input threshold and timing limits across temperature before using the link for production test data.

⚡

Low-Voltage Logic Interconnect

The DS90LT012ATMFX is appropriate for a short, low-voltage logic interconnect that benefits from differential transport and a single-ended CMOS destination. The receiver accepts 350 mV typical differential signals and reports open, shorted, and terminated link failures by holding its output HIGH, which simplifies link-state monitoring in many control systems. The design must ensure that the 3-V supply, CMOS output levels, and logic thresholds of the receiving device are compatible, and the differential trace should remain short to limit reflections.

🎥

Secure Camera or Sensor Link

The DS90LT012ATMFX can form the receiving endpoint of a short LVDS command or status connection from a camera module, remote sensor, or compact actuator assembly. Differential signaling helps preserve data integrity when the link shares a board with switching circuitry, and the integrated termination reduces receiver-side component count. Keep the connection away from motor and relay return currents, use a quiet ground reference, and verify the companion driver's amplitude and timing against the receiver's 350 mV typical input threshold.

推薦產品摘要

DS90LV012A Related single LVDS receiver family for designs using external termination 用於: Point-to-Point LVDS Clock Link, Industrial Command and Control Interface, Test and Measurement Instrument Link, Secure Camera or Sensor Link DS90LT012A Parent receiver family with integrated point-to-point termination 用於: Point-to-Point LVDS Clock Link, Industrial Command and Control Interface, LVDS Data Backplane Endpoint, Test and Measurement Instrument Link, Low-Voltage Logic Interconnect, Secure Camera or Sensor Link DS90LV011A Related single LVDS receiver family 用於: LVDS Data Backplane Endpoint, Low-Voltage Logic Interconnect
What is the DS90LT012ATMFX?
The DS90LT012ATMFX is a Texas Instruments 3-V LVDS single differential line receiver that converts low-voltage differential signals into 3-V CMOS outputs. According to the manufacturer datasheet, it accepts 350 mV typical differential input and includes an input termination resistor for point-to-point applications. It also detects open, shorted, and 100Ω-terminated inputs, driving its output HIGH during these fail-safe conditions.
Does the DS90LT012ATMFX include a 100-ohm input termination?
Yes, the DS90LT012ATMFX includes an input line termination resistor for point-to-point LVDS applications. The manufacturer identifies this feature as a principal distinction between the DS90LT012A and DS90LV012A receiver families. The integrated termination is listed as 100Ω and must be considered when calculating the load presented to the transmitter, cable, PCB traces, and connector.
What is the input sensitivity of DS90LT012ATMFX?
The DS90LT012ATMFX accepts differential LVDS input signals with a 350 mV typical input threshold. According to the Texas Instruments datasheet, the receiver translates these low-amplitude differential signals into 3-V CMOS output levels. Because the threshold is specified as typical, a completed design should use the manufacturer's minimum and maximum input specifications and verify signal integrity at the intended data rate.
Where can I download the DS90LT012ATMFX datasheet PDF?
The DS90LT012ATMFX datasheet PDF is available from the official Texas Instruments product page at https://www.ti.com/lit/ds/symlink/ds90lt012a.pdf. The document covers the DS90LT012A family, including the integrated line termination, differential input behavior, CMOS output, fail-safe response, package information, and recommended application circuits. Use the ordering-information section to distinguish the exact suffix.
Where is the DS90LT012ATMFX pinout?
The DS90LT012ATMFX pin assignment is shown in the pin-configuration and pin-functions tables of the official Texas Instruments DS90LT012A datasheet. The device uses a 5-pin SOT-23 package. Before assigning PCB nets, verify the power, ground, differential-input, and output locations directly against the pin diagram because the exact exposed pad and package terminal numbering must match the selected footprint.
What fail-safe conditions are supported by DS90LT012ATMFX?
The DS90LT012ATMFX supports open, shorted, and 100Ω-terminated input fail-safe conditions. According to the manufacturer datasheet, the receiver output is HIGH for all three conditions, providing a deterministic state when the physical LVDS link is not operating normally. This behavior helps system firmware distinguish an invalid link from a valid differential input, although the exact detection strategy remains application-specific.
Is DS90LT012ATMFX suitable for point-to-point LVDS links?
Yes, the DS90LT012ATMFX is specifically suited to point-to-point LVDS links because it contains an integrated input termination resistor. The receiver accepts a 350 mV typical differential input and produces a 3-V CMOS output. Keep the differential route short and balanced, place the receiver near the link endpoint, and confirm that the integrated 100Ω load is compatible with the companion transmitter and channel configuration.
What can replace the DS90LT012ATMFX?
The closest confirmed replacements are orderable variants within the Texas Instruments DS90LT012A family, provided the termination option, package, and suffix requirements remain unchanged. The manufacturer product page identifies DS90LT012ATMF and DS90LT012ATMF/NOPB as related orderable devices. Do not treat the DS90LV012A as an unconditional substitute because its integrated termination arrangement differs, and verify the complete suffix before approving a replacement.
What is the difference between DS90LT012A and DS90LV012A?
The principal documented difference is integrated line termination: the DS90LT012A includes an input termination resistor for point-to-point applications, while the DS90LV012A does not have the same termination feature. Both accept 350 mV typical differential inputs and produce 3-V CMOS outputs. Existing boards should not be converted between them without reviewing the input network and schematic for DS90LT012ATMFX.
DS90LT012ATMFX vs DS90LT012ATMF — which should I select?
Both devices are associated with the same Texas Instruments DS90LT012A receiver family and the same 5-pin SOT-23 implementation, but their orderable suffixes can encode different packing or production attributes. The DS90LT012ATMFX designation should be retained when that exact MPN is specified. Use the manufacturer ordering table to confirm reel configuration, quantity, and any environmental or termination options before substituting DS90LT012ATMF.
When should I choose DS90LT012ATMFX instead of a non-terminated LVDS receiver?
Choose the DS90LT012ATMFX when the design uses a point-to-point LVDS connection and an onboard 100Ω termination simplifies the receiver-end network. Select a non-terminated receiver when the PCB already provides an accurate termination, when multiple receiver loads share a line, or when the termination arrangement must remain externally adjustable. The correct choice depends on the line topology, not merely on receiver functionality.
Is DS90LT012ATMFX suitable for industrial equipment?
The DS90LT012ATMFX is identified as an industrial-temperature-grade interface device and is suitable for industrial point-to-point LVDS interfaces when the complete operating-temperature, supply, and reliability requirements are met. According to the manufacturer product information, it is a 3-V LVDS receiver with CMOS output and integrated termination. Validate the full temperature range and voltage limits against the published device limits before production release.
How should a DS90LT012ATMFX LVDS link be routed on a PCB?
Route the DS90LT012ATMFX differential input as a short, balanced pair on a continuous reference plane, with the receiver placed near the connector or transmitter endpoint. Maintain matched spacing and length through the pair, minimize vias and stubs, and place the receiver supply bypass capacitor close to its power pin. Because the receiver includes 100Ω termination, confirm that the transmitter can drive the resulting load without compromising edge rate or signal amplitude.
Where can I buy DS90LT012ATMFX and check its lead time?
Use the Request a Quote form on this page to request DS90LT012ATMFX availability, current lead time, and a quotation for the required quantity. The order code also carries packing information that must be preserved for manufacturing traceability. Confirm the final package suffix, reel quantity, and delivery schedule when placing the order rather than relying on a generic family-level listing.
What is the price of DS90LT012ATMFX?
Current DS90LT012ATMFX pricing and stock status are presented through the Request a Quote form on this page. The form is the appropriate channel for an exact-MPN quotation because ordering suffix and reel configuration can affect commercial availability. Submit the required quantity, manufacturing location, and target delivery date to receive a current response for the part number being purchased.
Is DS90LT012ATMFX in stock?
Current DS90LT012ATMFX inventory status should be confirmed through the Request a Quote form on this page. The exact MPN includes ordering information that may distinguish it from related DS90LT012A variants, so a family-level availability statement is not sufficient for production planning. Include your required quantity and target schedule when requesting a stock and lead-time update.
What are the key specifications of DS90LT012ATMFX that engineers should know?
The DS90LT012ATMFX is a 3-V, single-ended-output LVDS receiver with 350 mV typical differential input sensitivity, 100Ω integrated input termination, and HIGH-output fail-safe behavior for open, shorted, or terminated links. It is offered in a 5-pin SOT-23 package. According to the Texas Instruments datasheet, the DS90LT012A family supports these receiver and termination functions for compact point-to-point interfaces.

工程參考資料,適用於 DS90LT012ATMFX — 比較、設計指引及合規資訊。

選型指南

Select the DS90LT012ATMFX when a design needs a compact, single-channel 3-V LVDS receiver with an integrated 100Ω termination and HIGH-output fail-safe behavior for open, shorted, or terminated links. DS90LT012ATMF and its NOPB ordering code are closely related alternatives when their suffix-specific production and packing attributes meet the project requirements. DS90LV012ATMF is appropriate when the termination arrangement must be implemented externally, but it is not an unconditional substitute because removing the integrated 100Ω termination changes the receiver-end network. For a multi-drop bus, shared termination, non-LVDS differential input, or a package with a different pin count, do not select this family without a complete interface review. The existing PCB footprint, companion transmitter drive capability, logic thresholds, and required fail-safe behavior should all be confirmed before approving any replacement.

與替代品比較

參數 本產品 DS90LT012ATMF DS90LT012ATMF/NOPB DS90LT012ATMFX/NOPB DS90LV012ATMF
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package SOT-23-5 SOT-23-5 SOT-23-5 SOT-23-5 SOT-23-5
Device Type 3-V LVDS single differential line receiver 3-V LVDS single differential line receiver 3-V LVDS single differential line receiver 3-V LVDS single differential line receiver 3-V LVDS single differential line receiver
Receiver Count 1 receiver 1 receiver 1 receiver 1 receiver 1 receiver
Supply Voltage 3 V 3 V 3 V 3 V 3 V
Differential Input Threshold 350 mV typical 350 mV typical 350 mV typical 350 mV typical 350 mV typical
Output Level 3-V CMOS 3-V CMOS 3-V CMOS 3-V CMOS 3-V CMOS
Integrated Input Termination 100 Ω 100 Ω 100 Ω 100 Ω Not included
Fail-Safe Input Conditions Open, shorted, and 100 Ω terminated Open, shorted, and 100 Ω terminated Open, shorted, and 100 Ω terminated Open, shorted, and 100 Ω terminated Open, shorted, and 100 Ω terminated

主要差異化特點

  • Integrated receiver-end termination (對比DS90LV012ATMF)
  • Same electrical receiver ratings across ordering codes (對比DS90LT012ATMF)
  • Deterministic behavior for invalid physical links (對比DS90LT012ATMF)

設計說明

Route the differential input as a short, closely coupled pair over a continuous reference plane. Maintain symmetric geometry, minimize vias and stubs, and place the receiver near the cable or board connector. The integrated 100Ω termination presents a defined receiver-end load, so confirm the companion transmitter's output amplitude and edge rate with that load included in the channel analysis.

Place the receiver and its supply bypass capacitor close to the corresponding package pins. Keep the differential route away from switching-node copper, relay contacts, motor-return paths, and other high-current sources. Use a low-impedance ground reference for the receiver because differential signaling suppresses common-mode noise only to the extent that both conductors and their reference path remain balanced.

Do not replace the DS90LT012ATMFX with the DS90LV012A without reviewing the termination network, because the DS90LT012A includes an input termination intended for point-to-point use. Also preserve the exact ordering suffix when the distinction affects reel configuration or production traceability. Confirm the package pin map, supply limits, input thresholds, and fail-safe truth table against the manufacturer datasheet before release.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The manufacturer product page and datasheet identify the receiver family, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was available for the exact orderable suffix. The NOPB ordering code identifies a related lead-free finish but does not by itself establish the complete compliance status of DS90LT012ATMFX.

相關搜尋

DS90LT012ATMFX datasheet DS90LT012ATMFX pinout DS90LT012ATMFX datasheet pdf DS90LT012ATMFX equivalent DS90LT012ATMFX replacement DS90LT012ATMFX cross reference DS90LT012ATMFX footprint DS90LT012ATMFX price DS90LT012ATMFX stock Texas Instruments DS90LT012ATMFX DS90LT012A SOT-23-5 pinout DS90LT012ATMFX application circuit

相關元件與詞彙

Texas Instruments DS90LT012ATMFX DS90LT012A DS90LT012ATMF DS90LT012ATMFX/NOPB DS90LV012A DS90LV012ATMF DS90LV011A LVDS low-voltage differential signaling differential line receiver interface IC CMOS output 100Ω input termination fail-safe input 350 mV differential input SOT-23-5 SOT-23 package family surface-mount package point-to-point link differential pair signal integrity industrial interface Texas Instruments DS90LT012A datasheet
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情