DS90LT012ATMFX - 3V LVDS Receiver with 100Ω Termination
MPN: DS90LT012ATMFX ✓ فعالDS90LT012ATMFX نمای کلی
An LVDS receiver is an interface IC that detects a small differential voltage across a balanced pair of conductors and converts that signal into a single-ended CMOS output. LVDS belongs to the differential data-interface hierarchy, where low signal amplitude, common-mode rejection, and balanced routing improve signal integrity over longer point-to-point interconnects. The DS90LT012A family combines this receiver function with an onboard termination network intended to simplify point-to-point PCB designs.
Key features include 3-V CMOS output signaling, a typical input threshold of 350 mV, and integrated line termination. The receiver provides a HIGH output during open, shorted, and terminated fail-safe conditions, allowing downstream logic to identify an invalid physical link. Its five-pin SOT-23 package supports compact placement, while the integrated 100Ω termination removes the need for a separate input resistor in a conventional point-to-point LVDS connection.
The DS90LT012A architecture is optimized for receiving differential data from a companion LVDS transmitter over a short point-to-point connection. The receiver translates the differential input into a CMOS output referenced to the receiver supply. Because this is a single receiver rather than a multi-channel transceiver, board designers gain a compact solution for links that require one differential data channel, such as clock distribution, low-speed control links, or isolated command interfaces using compatible LVDS signaling.
Typical uses include LVDS clock-recovery links, point-to-point command and control channels, industrial equipment links, and test systems where a low-amplitude differential receiver is preferred. In a point-to-point circuit, the companion transmitter drives the differential pair and the DS90LT012ATMFX provides a direct CMOS output for the receiving controller or logic device. The integrated termination should be considered during signal-integrity analysis because it loads the transmission line and influences edge behavior.
PCB implementation requires a short, balanced route between the transmitter and receiver, with the differential pair terminated at the receiving end. Place the receiver close to the connector or driver to minimize stub length and reflections, maintain closely matched routing geometry, and connect the supply and ground pins to a low-impedance plane. The manufacturer datasheet should be used for final pin assignments, bypass requirements, and input/output truth tables before layout release.
This product overview combines the manufacturer interface description with practical comparison, application, and layout guidance. It highlights the DS90LT012ATMFX's integrated termination and fail-safe behavior while separating verified electrical facts from parameters that still require confirmation from the complete device documentation or an individual design validation.
جایگزینهای drop-in برای DS90LT012ATMFX — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
DS90LT012ATMF
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
DS90LT012ATMF/NOPB
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
DS90LT012ATMFX/NOPB
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
DS90LV012ATMF
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
DS90LT012ATMFX مشخصات
| Product Type | 3-V LVDS single differential line receiver |
| Receiver Configuration | 1 receiver |
| ولتاژ تغذیه | 3 V |
| Output Logic | 3-V CMOS |
| Typical Differential Input Threshold | 350 mV |
| Integrated Input Termination | 100 Ω |
| Fail-Safe Support | Open, shorted, and 100 Ω terminated inputs |
| Fail-Safe Output State | HIGH |
| بستهبندی | SOT-23-5 |
| Terminal Count | 5 terminals |
| نوع نصب | Surface mount |
| Temperature Grade | Industrial |
| Termination Configuration | Integrated for point-to-point applications |
| Input Type | Low-voltage differential input |
| نوع خروجی | Single-ended CMOS |
راهنمای پیکربندی پین DS90LT012ATMFX sot-23-5
پیکربندی پین برای DS90LT012ATMFX (پکیج sot-23-5). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای DS90LT012ATMFX.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
DS90LT012ATMFX مناسب است برای 6 کاربردs: Point-to-Point LVDS Clock Link, Industrial Command and Control Interface, LVDS Data Backplane Endpoint, Test and Measurement Instrument Link, Low-Voltage Logic Interconnect, Secure Camera or Sensor Link.
Point-to-Point LVDS Clock Link
The DS90LT012ATMFX fits a point-to-point clock link because it accepts a 350 mV typical differential LVDS input and converts it to a 3-V CMOS output. Its integrated 100Ω input termination removes the need for a separate receiver-end termination resistor in a conventional point-to-point topology. Place the receiver near the transmitter or connector, preserve a balanced route over a continuous reference plane, and confirm that the companion transmitter can drive the integrated load while maintaining the required edge rate and output amplitude.
پیشنهادی
Industrial Command and Control Interface
The DS90LT012ATMFX can convert a compact LVDS command link into a 3-V CMOS signal for an industrial controller, remote I/O module, or equipment-control board. Differential transport reduces sensitivity to common-mode noise relative to single-ended signaling, while the receiver's open, shorted, and 100Ω-terminated fail-safe behavior provides a defined HIGH output when the physical connection is invalid. Firmware can use that stable state to detect a disconnected or malformed link, although the overall protection strategy must fit the system's safety requirements.
پیشنهادی
LVDS Data Backplane Endpoint
The DS90LT012ATMFX is useful at the endpoint of a short differential data connection where a compact receiver and deterministic fail-safe response are required. The 350 mV typical input threshold supports low-amplitude LVDS detection, and the 3-V CMOS output can connect directly to suitable controller logic. Route the pair symmetrically, avoid long stubs, and assess the integrated 100Ω termination against the transmitter drive capability. For wider buses with multiple receivers, an external termination arrangement may be more appropriate.
پیشنهادی
Test and Measurement Instrument Link
The DS90LT012ATMFX can serve as the receive element in a compact differential link between instrument electronics and a controller. Its 3-V CMOS output provides a convenient logic-level result, while the integrated 100Ω termination simplifies a dedicated point-to-point route. Keep the receiver away from high-energy switching nodes, preserve controlled return current through the ground plane, and verify the complete input threshold and timing limits across temperature before using the link for production test data.
پیشنهادی
Low-Voltage Logic Interconnect
The DS90LT012ATMFX is appropriate for a short, low-voltage logic interconnect that benefits from differential transport and a single-ended CMOS destination. The receiver accepts 350 mV typical differential signals and reports open, shorted, and terminated link failures by holding its output HIGH, which simplifies link-state monitoring in many control systems. The design must ensure that the 3-V supply, CMOS output levels, and logic thresholds of the receiving device are compatible, and the differential trace should remain short to limit reflections.
پیشنهادی
Secure Camera or Sensor Link
The DS90LT012ATMFX can form the receiving endpoint of a short LVDS command or status connection from a camera module, remote sensor, or compact actuator assembly. Differential signaling helps preserve data integrity when the link shares a board with switching circuitry, and the integrated termination reduces receiver-side component count. Keep the connection away from motor and relay return currents, use a quiet ground reference, and verify the companion driver's amplitude and timing against the receiver's 350 mV typical input threshold.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای DS90LT012ATMFX — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | DS90LT012ATMF | DS90LT012ATMF/NOPB | DS90LT012ATMFX/NOPB | DS90LV012ATMF |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOT-23-5 | SOT-23-5 | SOT-23-5 | SOT-23-5 | SOT-23-5 |
| Device Type | 3-V LVDS single differential line receiver | 3-V LVDS single differential line receiver | 3-V LVDS single differential line receiver | 3-V LVDS single differential line receiver | 3-V LVDS single differential line receiver |
| Receiver Count | 1 receiver | 1 receiver | 1 receiver | 1 receiver | 1 receiver |
| Supply Voltage | 3 V | 3 V | 3 V | 3 V | 3 V |
| Differential Input Threshold | 350 mV typical | 350 mV typical | 350 mV typical | 350 mV typical | 350 mV typical |
| Output Level | 3-V CMOS | 3-V CMOS | 3-V CMOS | 3-V CMOS | 3-V CMOS |
| Integrated Input Termination | 100 Ω | 100 Ω | 100 Ω | 100 Ω | Not included |
| Fail-Safe Input Conditions | Open, shorted, and 100 Ω terminated | Open, shorted, and 100 Ω terminated | Open, shorted, and 100 Ω terminated | Open, shorted, and 100 Ω terminated | Open, shorted, and 100 Ω terminated |
تفاوتهای کلیدی
- Integrated receiver-end termination (در مقابلDS90LV012ATMF)
- Same electrical receiver ratings across ordering codes (در مقابلDS90LT012ATMF)
- Deterministic behavior for invalid physical links (در مقابلDS90LT012ATMF)
یادداشتهای طراحی
Route the differential input as a short, closely coupled pair over a continuous reference plane. Maintain symmetric geometry, minimize vias and stubs, and place the receiver near the cable or board connector. The integrated 100Ω termination presents a defined receiver-end load, so confirm the companion transmitter's output amplitude and edge rate with that load included in the channel analysis.
Place the receiver and its supply bypass capacitor close to the corresponding package pins. Keep the differential route away from switching-node copper, relay contacts, motor-return paths, and other high-current sources. Use a low-impedance ground reference for the receiver because differential signaling suppresses common-mode noise only to the extent that both conductors and their reference path remain balanced.
Do not replace the DS90LT012ATMFX with the DS90LV012A without reviewing the termination network, because the DS90LT012A includes an input termination intended for point-to-point use. Also preserve the exact ordering suffix when the distinction affects reel configuration or production traceability. Confirm the package pin map, supply limits, input thresholds, and fail-safe truth table against the manufacturer datasheet before release.
اطلاعات انطباق
The manufacturer product page and datasheet identify the receiver family, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was available for the exact orderable suffix. The NOPB ordering code identifies a related lead-free finish but does not by itself establish the complete compliance status of DS90LT012ATMFX.