EFM32G200F16G-E-QFN32 - 32MHz ARM Cortex-M3 MCU | Silicon Labs
MPN: EFM32G200F16G-E-QFN32 ✓ 啟用中EFM32G200F16G-E-QFN32 概覽
A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, volatile data memory, and peripherals into one package. The EFM32G200 belongs to the EFM32 Gecko family, combining an ARM Cortex-M3 processor with energy-saving modes, fast wake-up behavior, autonomous peripherals, and analog integration. This hierarchy places it between a general-purpose processor and a compact embedded control device.
The device provides 16 KB of Flash for firmware, 8 KB of RAM for working data, and two 16-bit timers. Its 32 MHz Cortex-M3 core provides 32-bit processing while retaining an energy-efficient architecture suitable for sensing, control, and communications nodes. The target variant includes 24 digital I/O pins and is identified as a device without AES hardware, so security-sensitive designs should account for that limitation.
Low-power operation is central to the platform. The manufacturer datasheet states that EFM32G devices can consume as little as 0.6 µA in Stop mode and 180 µA/MHz in Run mode. Fast wake-up and energy-saving modes reduce the time the processor spends active, while autonomous peripherals can reduce the need for frequent CPU intervention. These characteristics make the MCU suitable for duty-cycled battery-powered products.
Typical uses include environmental sensing, industrial condition monitoring, compact control panels, wearable accessories, low-power IoT endpoints, and embedded sensor nodes. The 24 I/O pins support digital interfaces and discrete controls, while the two timers support periodic sensing, timing, pulse generation, and motor or actuator control. Firmware size must remain within the 16 KB Flash limit.
For PCB implementation, use the 32-QFN land pattern and connect the exposed thermal pad according to the manufacturer pinout and layout guidance. Place decoupling capacitors close to the supply pins and preserve copper beneath the exposed pad for electrical and thermal performance. Confirm the exact pin assignments in the EFM32G200 datasheet before routing board-level interfaces.
This product page combines the manufacturer specifications, lifecycle information, drop-in family alternatives, application guidance, and practical layout considerations in one engineering reference. It supports faster MCU selection while highlighting the memory limit, package constraints, low-power operating modes, and software implications that must be checked before a design is released to production.
直接替換替代品,適用於 EFM32G200F16G-E-QFN32 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: EFM32G200F16G-E-QFN32 (相同外形與佔位) — 差異在於 Package, Run Mode Current, Digital I/O Pins, Timers, RAM.
EFM32G200F16-QFN32
✅ 直接替換聯絡詢價
查看資料表 →EFM32G200F32G-E-QFN32
✅ 直接替換聯絡詢價
查看資料表 →EFM32G200F32-QFN32
✅ 直接替換聯絡詢價
查看資料表 →EFM32G200F16G-E-QFN32 最大額定值與電氣特性
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Processor Core | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 16 KB |
| RAM Memory | 8 KB |
| Digital I/O Pins | 24 pins |
| Timers | 2 x 16-bit timers |
| Core Architecture | 32-bit single-core |
| Supply Voltage Range | 1.98 V to 3.8 V |
| Nominal Supply Voltage | 2.5 V or 3.3 V |
| Stop Mode Current | 0.6 µA |
| Run Mode Current | 180 µA/MHz |
| 封裝 | 32-QFN (6 x 6 mm) |
| 腳位數 | 32 pins |
| 安裝類型 | Surface mount |
| AES Hardware Accelerator | Not included |
| Low-Power Features | Stop mode, fast wake-up, and energy-saving modes |
| Delivery Format | Tape and reel |
EFM32G200F16G-E-QFN32 32-qfn (6 x 6 mm) 腳位配置指南
EFM32G200F16G-E-QFN32(32-qfn (6 x 6 mm) 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: EFM32G200F16G-E-QFN32.
請參閱 資料表 以查看完整腳位配置。
典型應用
EFM32G200F16G-E-QFN32 適用於 6 應用s: Battery-Powered Sensor Nodes, Industrial Condition Monitoring, Low-Power IoT Endpoints, Wearable and Personal Accessories, Compact Control Panels, Timing and Event-Control Modules.
Battery-Powered Sensor Nodes
The EFM32G200F16G-E-QFN32 fits compact environmental and industrial sensor nodes that spend most of their time asleep. Its Cortex-M3 core operates up to 32 MHz for local processing, while the EFM32G platform can reach 0.6 µA in Stop mode. The 16 KB Flash accommodates compact protocol and acquisition firmware, and the 8 KB RAM supports sensor buffering without demanding a larger memory footprint. A duty-cycled design can wake the MCU, collect a reading, transmit data, and return to Stop mode. Actual battery life also depends on the sensor, radio, voltage regulator, and wake-up frequency.
推薦
Industrial Condition Monitoring
The EFM32G200F16G-E-QFN32 is suitable for industrial monitoring modules that sample switches, sensors, or digital equipment status and transmit periodic measurements. Its 24 digital I/O pins provide capacity for multiple discrete inputs, while two 16-bit timers support periodic sampling and event timing. The 32 MHz Cortex-M3 core can process locally and avoid continuous cloud communication. Its 1.98 V to 3.8 V operating range also provides flexibility around regulated industrial rails, although the final power architecture must satisfy transient and grounding requirements.
推薦
Low-Power IoT Endpoints
The EFM32G200F16G-E-QFN32 works well in compact IoT endpoints that combine a sensor interface with a low-rate communications link. Its 180 µA/MHz Run-mode figure allows duty-cycled processing at 32 MHz, while Stop mode supports a low standby floor of 0.6 µA. Sixteen kilobytes of Flash and 8 KB of RAM are sufficient for small protocol stacks and application logic. Designers should reserve memory for the bootloader, configuration data, and stack headroom, then use the larger 32 KB family member if firmware exceeds the 16 KB limit.
推薦
Wearable and Personal Accessories
The EFM32G200F16G-E-QFN32 can manage a compact wearable accessory or personal-device peripheral that must balance processing capability with battery consumption. The 6 x 6 mm 32-QFN package saves board area, and the low-power operating modes are appropriate for accessories that remain inactive for extended periods. Twenty-four digital I/O pins and two 16-bit timers support buttons, indicators, haptic timing, and peripheral interfaces. The 16 KB Flash limit requires disciplined firmware sizing, so applications with larger graphical or connectivity workloads should assess a higher-memory MCU.
推薦
Compact Control Panels
The EFM32G200F16G-E-QFN32 can act as the central controller in a compact control panel for a small appliance, instrument, or embedded system. Its 24 digital I/O pins can operate LEDs, switches, relays, or digital interfaces, and its timers can manage periodic control tasks. The 32 MHz Cortex-M3 core provides responsive sequential control without a separate processor. Because the target has no AES hardware, secure connectivity may require software cryptography or a companion security device, which should be evaluated before product architecture is frozen.
推薦
Timing and Event-Control Modules
The EFM32G200F16G-E-QFN32 is appropriate for modules dominated by timers, digital events, and periodic control. It includes two 16-bit timers and 24 digital I/O pins, allowing multiple input captures, output comparisons, and discrete event channels to be coordinated by a 32 MHz Cortex-M3 core. Fast wake-up behavior can support short active windows, while Stop mode can reduce consumption between events. Designers should verify peripheral routing, interrupt behavior, and the exact QFN pin assignment in the manufacturer documentation before committing the board layout.
推薦
推薦產品摘要
工程參考資料,適用於 EFM32G200F16G-E-QFN32 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | EFM32G200F16-QFN32 | EFM32G200F32G-E-QFN32 | EFM32G200F32-QFN32 |
|---|---|---|---|---|
| Package | 32-QFN (6 x 6 mm) | 32-QFN (6 x 6 mm) | 32-QFN (6 x 6 mm) | 32-QFN (6 x 6 mm) |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 16 KB | 16 KB | 32 KB | 32 KB |
| RAM Memory | 8 KB | 8 KB | 8 KB | 8 KB |
| Digital I/O Pins | 24 pins | 24 pins | 24 pins | 24 pins |
| Timers | 2 x 16-bit timers | 2 x 16-bit timers | 2 x 16-bit timers | 2 x 16-bit timers |
主要差異化特點
- Lower program-memory demand for compact control firmware (對比EFM32G200F32G-E-QFN32)
- Lower-power EFM32G200 processing platform (對比EFM32G200F16-QFN32)
- Identical core and memory for firmware-compatible family scaling (對比EFM32G200F32-QFN32)
設計說明
Use the manufacturer 32-QFN land pattern and place input, output, and decoupling capacitors close to their associated power pins. Keep the exposed-pad connection and ground-plane geometry consistent with the EFM32G200 layout guidance. A compact 6 x 6 mm footprint leaves little room for long return paths, so noisy or switching circuitry should be positioned away from sensitive signal and reference routing.
Design the supply for the documented 1.98 V to 3.8 V operating range and confirm startup voltage behavior for the selected system. Estimated power use scales with the 180 µA/MHz Run-mode figure, but actual consumption depends on clock configuration, active time, peripherals, and leakage. Use Stop mode only after validating wake-up requirements, and account for the 0.6 µA device-level value as an MCU contribution rather than a complete system-current figure.
Route high-speed or sensitive signals away from switching nodes, inductor connections, and the exposed-pad supply region. The QFN lead pitch requires compact escape routing, so verify each net against the pin table before fabrication. For designs using the 32 KB Flash family variant, do not assume the bootloader address and firmware layout are interchangeable with the 16 KB device without reviewing the relevant configuration procedure.
Avoid designing firmware that depends on the full 16 KB Flash without reserving space for the bootloader, stack, constants, and future updates. The MCU has no AES hardware, so security designs must not assume hardware-accelerated encryption. Also distinguish the functional ordering code from reel or packaging suffix changes, and verify the exact qualification and temperature requirements before releasing a production BOM.
合規資訊
Compliance attributes are not stated in the manufacturer product page, distributor snippets, or family datasheet excerpts available for this device.