EFM32G200F16G-E-QFN32 - 32MHz ARM Cortex-M3 MCU | Silicon Labs
부품 번호: EFM32G200F16G-E-QFN32 ✓ 활성EFM32G200F16G-E-QFN32 개요
A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, volatile data memory, and peripherals into one package. The EFM32G200 belongs to the EFM32 Gecko family, combining an ARM Cortex-M3 processor with energy-saving modes, fast wake-up behavior, autonomous peripherals, and analog integration. This hierarchy places it between a general-purpose processor and a compact embedded control device.
The device provides 16 KB of Flash for firmware, 8 KB of RAM for working data, and two 16-bit timers. Its 32 MHz Cortex-M3 core provides 32-bit processing while retaining an energy-efficient architecture suitable for sensing, control, and communications nodes. The target variant includes 24 digital I/O pins and is identified as a device without AES hardware, so security-sensitive designs should account for that limitation.
Low-power operation is central to the platform. The manufacturer datasheet states that EFM32G devices can consume as little as 0.6 µA in Stop mode and 180 µA/MHz in Run mode. Fast wake-up and energy-saving modes reduce the time the processor spends active, while autonomous peripherals can reduce the need for frequent CPU intervention. These characteristics make the MCU suitable for duty-cycled battery-powered products.
Typical uses include environmental sensing, industrial condition monitoring, compact control panels, wearable accessories, low-power IoT endpoints, and embedded sensor nodes. The 24 I/O pins support digital interfaces and discrete controls, while the two timers support periodic sensing, timing, pulse generation, and motor or actuator control. Firmware size must remain within the 16 KB Flash limit.
For PCB implementation, use the 32-QFN land pattern and connect the exposed thermal pad according to the manufacturer pinout and layout guidance. Place decoupling capacitors close to the supply pins and preserve copper beneath the exposed pad for electrical and thermal performance. Confirm the exact pin assignments in the EFM32G200 datasheet before routing board-level interfaces.
This product page combines the manufacturer specifications, lifecycle information, drop-in family alternatives, application guidance, and practical layout considerations in one engineering reference. It supports faster MCU selection while highlighting the memory limit, package constraints, low-power operating modes, and software implications that must be checked before a design is released to production.
드롭인 대체품: EFM32G200F16G-E-QFN32 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: EFM32G200F16G-E-QFN32 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Run Mode Current, Digital I/O Pins, Timers, RAM.
EFM32G200F16-QFN32
✅ 드롭인가격 문의
데이터시트 보기 →EFM32G200F32G-E-QFN32
✅ 드롭인가격 문의
데이터시트 보기 →EFM32G200F32-QFN32
✅ 드롭인가격 문의
데이터시트 보기 →EFM32G200F16G-E-QFN32 최대 정격 & 전기적 특성
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Processor Core | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 16 KB |
| RAM Memory | 8 KB |
| Digital I/O Pins | 24 pins |
| Timers | 2 x 16-bit timers |
| Core Architecture | 32-bit single-core |
| Supply Voltage Range | 1.98 V to 3.8 V |
| Nominal Supply Voltage | 2.5 V or 3.3 V |
| Stop Mode Current | 0.6 µA |
| Run Mode Current | 180 µA/MHz |
| 패키지 | 32-QFN (6 x 6 mm) |
| 핀 수 | 32 pins |
| 실장 유형 | Surface mount |
| AES Hardware Accelerator | Not included |
| Low-Power Features | Stop mode, fast wake-up, and energy-saving modes |
| Delivery Format | Tape and reel |
EFM32G200F16G-E-QFN32 32-qfn (6 x 6 mm) 핀 구성 가이드
EFM32G200F16G-E-QFN32(32-qfn (6 x 6 mm) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: EFM32G200F16G-E-QFN32.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
EFM32G200F16G-E-QFN32 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Nodes, Industrial Condition Monitoring, Low-Power IoT Endpoints, Wearable and Personal Accessories, Compact Control Panels, Timing and Event-Control Modules.
Battery-Powered Sensor Nodes
The EFM32G200F16G-E-QFN32 fits compact environmental and industrial sensor nodes that spend most of their time asleep. Its Cortex-M3 core operates up to 32 MHz for local processing, while the EFM32G platform can reach 0.6 µA in Stop mode. The 16 KB Flash accommodates compact protocol and acquisition firmware, and the 8 KB RAM supports sensor buffering without demanding a larger memory footprint. A duty-cycled design can wake the MCU, collect a reading, transmit data, and return to Stop mode. Actual battery life also depends on the sensor, radio, voltage regulator, and wake-up frequency.
추천
Industrial Condition Monitoring
The EFM32G200F16G-E-QFN32 is suitable for industrial monitoring modules that sample switches, sensors, or digital equipment status and transmit periodic measurements. Its 24 digital I/O pins provide capacity for multiple discrete inputs, while two 16-bit timers support periodic sampling and event timing. The 32 MHz Cortex-M3 core can process locally and avoid continuous cloud communication. Its 1.98 V to 3.8 V operating range also provides flexibility around regulated industrial rails, although the final power architecture must satisfy transient and grounding requirements.
추천
Low-Power IoT Endpoints
The EFM32G200F16G-E-QFN32 works well in compact IoT endpoints that combine a sensor interface with a low-rate communications link. Its 180 µA/MHz Run-mode figure allows duty-cycled processing at 32 MHz, while Stop mode supports a low standby floor of 0.6 µA. Sixteen kilobytes of Flash and 8 KB of RAM are sufficient for small protocol stacks and application logic. Designers should reserve memory for the bootloader, configuration data, and stack headroom, then use the larger 32 KB family member if firmware exceeds the 16 KB limit.
추천
Wearable and Personal Accessories
The EFM32G200F16G-E-QFN32 can manage a compact wearable accessory or personal-device peripheral that must balance processing capability with battery consumption. The 6 x 6 mm 32-QFN package saves board area, and the low-power operating modes are appropriate for accessories that remain inactive for extended periods. Twenty-four digital I/O pins and two 16-bit timers support buttons, indicators, haptic timing, and peripheral interfaces. The 16 KB Flash limit requires disciplined firmware sizing, so applications with larger graphical or connectivity workloads should assess a higher-memory MCU.
추천
Compact Control Panels
The EFM32G200F16G-E-QFN32 can act as the central controller in a compact control panel for a small appliance, instrument, or embedded system. Its 24 digital I/O pins can operate LEDs, switches, relays, or digital interfaces, and its timers can manage periodic control tasks. The 32 MHz Cortex-M3 core provides responsive sequential control without a separate processor. Because the target has no AES hardware, secure connectivity may require software cryptography or a companion security device, which should be evaluated before product architecture is frozen.
추천
Timing and Event-Control Modules
The EFM32G200F16G-E-QFN32 is appropriate for modules dominated by timers, digital events, and periodic control. It includes two 16-bit timers and 24 digital I/O pins, allowing multiple input captures, output comparisons, and discrete event channels to be coordinated by a 32 MHz Cortex-M3 core. Fast wake-up behavior can support short active windows, while Stop mode can reduce consumption between events. Designers should verify peripheral routing, interrupt behavior, and the exact QFN pin assignment in the manufacturer documentation before committing the board layout.
추천
추천 제품 요약
엔지니어링 참조 데이터: EFM32G200F16G-E-QFN32 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | EFM32G200F16-QFN32 | EFM32G200F32G-E-QFN32 | EFM32G200F32-QFN32 |
|---|---|---|---|---|
| Package | 32-QFN (6 x 6 mm) | 32-QFN (6 x 6 mm) | 32-QFN (6 x 6 mm) | 32-QFN (6 x 6 mm) |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 16 KB | 16 KB | 32 KB | 32 KB |
| RAM Memory | 8 KB | 8 KB | 8 KB | 8 KB |
| Digital I/O Pins | 24 pins | 24 pins | 24 pins | 24 pins |
| Timers | 2 x 16-bit timers | 2 x 16-bit timers | 2 x 16-bit timers | 2 x 16-bit timers |
주요 차별점
- Lower program-memory demand for compact control firmware (vs EFM32G200F32G-E-QFN32)
- Lower-power EFM32G200 processing platform (vs EFM32G200F16-QFN32)
- Identical core and memory for firmware-compatible family scaling (vs EFM32G200F32-QFN32)
설계 노트
Use the manufacturer 32-QFN land pattern and place input, output, and decoupling capacitors close to their associated power pins. Keep the exposed-pad connection and ground-plane geometry consistent with the EFM32G200 layout guidance. A compact 6 x 6 mm footprint leaves little room for long return paths, so noisy or switching circuitry should be positioned away from sensitive signal and reference routing.
Design the supply for the documented 1.98 V to 3.8 V operating range and confirm startup voltage behavior for the selected system. Estimated power use scales with the 180 µA/MHz Run-mode figure, but actual consumption depends on clock configuration, active time, peripherals, and leakage. Use Stop mode only after validating wake-up requirements, and account for the 0.6 µA device-level value as an MCU contribution rather than a complete system-current figure.
Route high-speed or sensitive signals away from switching nodes, inductor connections, and the exposed-pad supply region. The QFN lead pitch requires compact escape routing, so verify each net against the pin table before fabrication. For designs using the 32 KB Flash family variant, do not assume the bootloader address and firmware layout are interchangeable with the 16 KB device without reviewing the relevant configuration procedure.
Avoid designing firmware that depends on the full 16 KB Flash without reserving space for the bootloader, stack, constants, and future updates. The MCU has no AES hardware, so security designs must not assume hardware-accelerated encryption. Also distinguish the functional ordering code from reel or packaging suffix changes, and verify the exact qualification and temperature requirements before releasing a production BOM.
규정 준수 정보
Compliance attributes are not stated in the manufacturer product page, distributor snippets, or family datasheet excerpts available for this device.