ICL7650CSA+ - 2MHz Zero-Drift Op Amp | Maxim Integrated
MPN: ICL7650CSA+ ✓ 啟用中ICL7650CSA+ 概覽
A zero-drift operational amplifier is a voltage-feedback amplifier that continuously corrects its input-offset voltage and other low-frequency errors. The ICL7650 family belongs to the chopper-stabilized amplifier class, a subtype of precision operational amplifiers used when low DC offset and high DC gain matter more than wideband noise. The result is a useful combination of very high DC accuracy, low input bias current, and a conventional SOIC-8 implementation.
Key features include 2 MHz gain-bandwidth product, 2.5 V/µs slew rate, 1.5 pA input bias current, and 130 dB open-loop gain. The 4.5 V to 16 V total supply range supports both positive single-supply operation and split supplies up to ±8 V. The chopper-stabilized architecture is particularly useful for current-to-voltage conversion, bridge-sensor conditioning, low-level voltage measurement, and instrumentation-amplifier input stages where offset drift can obscure the wanted signal.
The ICL7650CSA+ is identified as a single-circuit amplifier in the SOIC-8 package. Its 2 MHz bandwidth provides useful response beyond DC, allowing the device to process signals well above the very-low-frequency range in which its zero-drift correction is most important. Input-bias and offset characteristics must still be evaluated together: extremely low bias current does not by itself determine the total measurement error if source resistance, noise, or common-mode limits are unsuitable.
Typical applications include precision current measurement, strain-gauge and bridge sensor interfaces, low-level signal conditioning, laboratory instrumentation, and high-impedance sensor amplifiers. In a transimpedance stage, the 1.5 pA input bias current can limit the voltage error created across a high-value feedback resistor. In bridge measurements, the 130 dB open-loop gain supports accurate closed-loop gain, provided the output remains within its voltage range and the common-mode input stays within the amplifier's permitted range.
The primary design consideration is power-supply headroom. A 2.5 V/µs slew rate and 2 MHz bandwidth can produce a large output transition faster than the load can settle, so feedback compensation and output isolation should be checked with the intended load. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should be routed away from switching nodes and high-current return paths.
This page combines the ICL7650CSA+ specifications, practical zero-drift amplifier design guidance, application-focused circuit roles, and parameter comparisons with same-package alternatives. These engineering details help engineers select the amplifier and plan the surrounding sensor, feedback, filtering, and layout requirements with fewer board-level iterations.
直接替換替代品,適用於 ICL7650CSA+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ICL7650CSA+ (相同外形與佔位) — 差異在於 Amplifier Type, Input Bias Current, Supply Voltage Range.
ICL7650CSA
✅ 直接替換📋 參考替代品(不在目錄中)
ICL7650CSA-T
✅ 直接替換📋 參考替代品(不在目錄中)
ICL7650CSA+T
✅ 直接替換📋 參考替代品(不在目錄中)
ICL7653CSA
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →ICL7650SCBA-1
✅ 直接替換📋 參考替代品(不在目錄中)
ICL7650CSA+ 最大額定值與電氣特性
| Amplifier Type | Chopper-Stabilized Zero-Drift Operational Amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 2 MHz |
| Slew Rate | 2.5 V/µs |
| Input Bias Current | 1.5 pA |
| Open-Loop Gain | 130 dB |
| Supply Voltage Range | 4.5 V to 16 V |
| Single-Supply Operating Range | Up to 16 V |
| Split-Supply Operating Range | ±2.25 V to ±8 V |
| 封裝 | 8-pin SOIC |
| Package Width | 3.90 mm |
| 安裝類型 | Surface Mount |
ICL7650CSA+ 3.90 mm 腳位配置指南
ICL7650CSA+(3.90 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: ICL7650CSA+.
請參閱 資料表 以查看完整腳位配置。
典型應用
ICL7650CSA+ 適用於 6 應用s: Precision Current-to-Voltage Conversion, Bridge Sensor Signal Conditioning, High-Impedance Sensor Amplification, Laboratory Instrumentation, Low-Level Voltage Measurement, Audio and Instrumentation Signal Paths.
Precision Current-to-Voltage Conversion
The ICL7650CSA+ fits a transimpedance stage that converts a small sensor current into a measurable voltage. Its specified input bias current of 1.5 pA is especially useful with high-value feedback resistors, where bias-current error would otherwise create a significant output offset. The 130 dB open-loop gain supports accurate closed-loop operation, while the 2 MHz gain-bandwidth product handles signals beyond DC. The circuit still requires careful feedback-layout control and a compatible transimpedance-capacitor strategy to maintain stability.
推薦
Bridge Sensor Signal Conditioning
The ICL7650CSA+ can serve as the input amplifier for resistive bridge sensors where small differential signals must be amplified without substantial low-frequency offset movement. Its chopper-stabilized architecture targets low DC offset drift, and the 1.5 pA input bias current reduces excitation of high-impedance sensor nodes. The 4.5 V to 16 V supply range supports compact industrial instrumentation, although the input common-mode range, excitation voltage, and output swing must be checked against the chosen bridge and ADC.
推薦
High-Impedance Sensor Amplification
The ICL7650CSA+ is appropriate for buffering high-impedance sensors where leakage from the input stage could corrupt the measured signal. Its 1.5 pA input bias current limits the current drawn from the sensor node, and the high open-loop gain of 130 dB supports accurate low-frequency amplification. Designers should still calculate the bias-induced error against source impedance, guard sensitive nodes, and verify that the selected gain is stable with the sensor capacitance and wiring length.
推薦
Laboratory Instrumentation
The ICL7650CSA+ supports laboratory measurement circuits that need low DC offset but do not require high-speed general-purpose performance. Its 2 MHz gain-bandwidth product and 2.5 V/µs slew rate provide adequate bandwidth for many low-frequency and moderate-frequency signals, while chopper stabilization improves DC behavior. It is useful in buffered instrument inputs, programmable-gain stages, and reference-adjacent circuits, provided the designer accounts for chopped-amplifier noise around the correction frequency and avoids driving a capacitive load directly.
推薦
Low-Level Voltage Measurement
The ICL7650CSA+ is useful when a low-level voltage must be amplified without accepting large low-frequency offset errors. The 130 dB open-loop gain supports accurate inverting and noninverting gain stages, while the low input bias current minimizes loading of the measured source. A practical implementation should use short, guarded input traces, local supply decoupling, and an output range that remains inside the device's operating limits. The 4.5 V minimum supply gives flexibility for low-voltage measurement systems.
推薦
Audio and Instrumentation Signal Paths
The ICL7650CSA+ can handle low-level audio or instrumentation signals where low DC offset helps preserve small-signal fidelity. Its 2.5 V/µs slew rate and 2 MHz bandwidth allow it to process signals beyond the DC region, while the 1.5 pA input bias current suits high-impedance sources. For audio paths, compare the amplifier's chopper-related noise spectrum with the system noise floor and avoid excessive gain that amplifies both the wanted signal and correction-region artifacts.
推薦
推薦產品摘要
工程參考資料,適用於 ICL7650CSA+ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ICL7650CSA | ICL7650CSA-T | ICL7650CSA+T | ICL7653CSA | ICL7650SCBA-1 |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 8-pin SOIC | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same |
| Amplifier Architecture | Chopper-stabilized zero-drift | Chopper-stabilized zero-drift | Chopper-stabilized zero-drift | Chopper-stabilized zero-drift | Chopper-stabilized zero-drift with shutdown control | Chopper-stabilized zero-drift |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Ordering and Temperature Options | ICL7650CSA+ commercial ordering designation | Base commercial designation | Temperature-grade designation | Tape-and-reel designation | Shutdown-control family designation | Older family designation |
主要差異化特點
- Low input bias current supports high-impedance measurement (對比ICL7650CSA)
- Direct SOIC-8 family interchangeability (對比ICL7650CSA-T)
- Higher DC gain than a typical general-purpose precision amplifier (對比ICL7653CSA)
設計說明
Do not treat a chopper-stabilized amplifier as a direct substitute for every general-purpose op amp. Its zero-drift correction changes the noise spectrum and can introduce artifacts near the chopper frequency. Before choosing the ICL7650CSA+ for audio, communications, or wideband instrumentation, compare those artifacts with the system noise floor. Also verify the common-mode input range, output swing, and stability because the 4.5 V to 16 V supply specification alone does not guarantee useful signal headroom.
Place input and output compensation components close to their associated pins, and route sensitive input traces away from power-converter nodes and high-current return paths. For a transimpedance application, keep the feedback resistor and compensation capacitor compact to minimize parasitic capacitance and feedback-loop delay. The ICL7650CSA+ offers a 2 MHz gain-bandwidth product and 2.5 V/µs slew rate, so high closed-loop gain combined with stray capacitance can produce ringing even when the DC operating point is correct.
Design the power rail around the 4.5 V minimum supply requirement and preserve headroom for the output swing. Decouple the supply pins locally and verify ripple at the amplifier pins, particularly when an upstream switching converter is used. A 2.5 V/µs slew rate can produce rapid output transitions, so the regulator and decoupling network should have sufficient response for the selected load and loop bandwidth. Follow the capacitor values and stability guidance in the Maxim Integrated datasheet.
For high-impedance sensors, minimize leakage from PCB contamination, humidity, connectors, and adjacent digital traces. The 1.5 pA input bias current is small, but its effect scales with source impedance, and it should not be interpreted as the amplifier's complete input-referred error. Guard or shield the sensitive node where practical, use clean boards, and evaluate offset drift and noise over the temperature range required by the final system.
合規資訊
Exact environmental-compliance status for the selected ordering suffix and manufacturing lot must be confirmed through the Request a Quote form.