INA105KPG4 - 1MHz Differential Amplifier | Texas Instruments
MPN: INA105KPG4 ✓ 啟用中INA105KPG4 概覽
A differential amplifier is a voltage-regulating amplifier that rejects a voltage common to both inputs while amplifying the difference between them. The INA105 belongs to the instrumentation-amplifier and differential-amplifier hierarchy, where precise resistor matching improves common-mode rejection and gain accuracy. This capability is useful when a small sensor or measurement signal must be extracted from a larger voltage that also drives the system.
The key feature of the INA105 is its internally trimmed, unity-gain network. Laser trimming establishes accurate gain and high common-mode rejection, while matched resistor temperature coefficients help maintain performance over changing temperature. The INA105KPG4 operates from a minimum dual supply of ±5 V. Its 1 MHz bandwidth supports signals extending from low-frequency instrumentation into audio and industrial control bandwidths, while the 3 V/us slew rate allows large signal changes without excessive distortion.
The monolithic construction simplifies differential measurement by eliminating the four external precision resistors normally associated with a unity-gain subtractor. It does not provide the adjustable gain available in higher-gain differential amplifier families, so applications requiring substantial gain should include an additional gain stage. Designers must also verify that signal and output voltages remain inside the amplifier's input and output common-mode limits.
Typical uses include bridge-transducer interfaces, current-shunt measurements, instrumentation front ends, industrial sensing, and differential signal conditioning. The fixed unity-gain relationship makes the device particularly suitable when the following circuit requires a balanced or translated differential result without an external resistor network.
For PCB implementation, treat the eight-pin PDIP as a through-hole precision analog component. Keep input and output traces short, connect decoupling capacitors close to the supply pins, and avoid routing high-current or switching-node copper near the input terminals. Verify reference-ground arrangements carefully because common-mode rejection depends on clean grounding and symmetric signal paths.
This page combines the manufacturer's device description with package, frequency, and slew-rate data, organized drop-in alternatives, comparison parameters, and practical circuit guidance. The technical sections help engineers evaluate the INA105KPG4 for precision differential measurements, identify sourcing options through the Request a Quote form, and plan a robust implementation without redundant datasheet navigation.
直接替換替代品,適用於 INA105KPG4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: INA105KPG4 (相同外形與佔位) — 差異在於 Mounting Type, Package, Product Type.
INA105KPG4 最大額定值與電氣特性
| Product Type | Precision unity-gain differential amplifier |
| Number of Amplifiers | 1 circuit |
| Gain | 1 V/V |
| Bandwidth | 1 MHz |
| Slew Rate | 3 V/us |
| Input Offset Voltage | 500 uV maximum |
| Minimum Supply Voltage | ±5 V |
| Internal Resistor Network | Laser-trimmed metal-film resistors |
| 封裝 | 8-pin PDIP |
| 安裝類型 | Through-hole |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
| Safe Operating Area | not applicable to this linear amplifier |
INA105KPG4 8-pin pdip 腳位配置指南
INA105KPG4(8-pin pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: INA105KPG4.
請參閱 資料表 以查看完整腳位配置。
典型應用
INA105KPG4 適用於 6 應用s: Bridge Transducer Interface, Current-Shunt Measurement, Industrial Sensor Signal Conditioning, Precision Instrumentation Front End, Audio-Range Differential Interface, Laboratory and Test Equipment.
Bridge Transducer Interface
The INA105KPG4 is suitable for conditioning the small differential output of a resistive bridge because its fixed unity gain preserves the bridge signal while its laser-trimmed internal network is designed for accurate gain and high common-mode rejection. The 500 uV maximum input offset specification is especially relevant when the transducer output is small. Place the amplifier close to the bridge and keep the two input routes geometrically similar to minimize conversion of common-mode interference into differential error.
推薦
Current-Shunt Measurement
For current-shunt monitoring, the INA105KPG4 can amplify the shunt's differential voltage without external unity-gain resistors. Its 1 MHz bandwidth accommodates many industrial control and diagnostic signals, while the 3 V/us slew rate permits fast changes in the measured current. The main design constraint is common-mode range: shunt voltage must remain within the amplifier's permitted input range, and Kelvin routing should connect the sense terminals directly to the amplifier.
推薦
Industrial Sensor Signal Conditioning
The INA105KPG4 fits industrial sensor front ends that present a differential output superimposed on a common-mode voltage. Its unity-gain topology and laser-trimmed resistor network reduce dependence on external resistor matching, while common-mode rejection helps isolate the desired sensor signal. With ±5 V minimum dual-supply operation, the device is appropriate for ±15 V or ±12 V instrumentation systems, subject to the input and output range limits stated in the manufacturer datasheet.
推薦
Precision Instrumentation Front End
The INA105KPG4 can serve as the first differential stage in a precision instrumentation front end when unity gain is sufficient. Its 1 MHz bandwidth supports signal bandwidth beyond traditional slow industrial measurements, and the 500 uV maximum input offset establishes a useful baseline for low-level differential measurements. Use a grounded guard or shielding strategy when source impedance is high, and verify that output swing remains adequate before adding another gain stage.
推薦
Audio-Range Differential Interface
The INA105KPG4 is usable for audio-range differential interfaces when the system requires a fixed unity-gain differential transfer function and a 1 MHz bandwidth. The 3 V/us slew rate is adequate for many low-to-moderate amplitude audio signals, but distortion must be checked at the highest expected frequency and output level. The DIP package favors prototype and legacy equipment rather than compact consumer audio products, so the mechanical footprint should be considered before design selection.
推薦
Laboratory and Test Equipment
The INA105KPG4 is appropriate for laboratory differential input stages because its internal unity-gain network reduces the number of precision external components that must be selected and matched. The 1 MHz bandwidth supports many general-purpose waveform and instrumentation tasks, while the 3 V/us slew rate covers signals with moderate edge rates. For bench designs, place the device on a low-noise prototype area and verify source impedance, grounding, and output saturation before calibration.
推薦
推薦產品摘要
工程參考資料,適用於 INA105KPG4 — 比較、設計指引及合規資訊。
選型指南
Do not select the INA105 family solely by its 1 MHz bandwidth. First confirm common-mode range, output swing, offset voltage, common-mode rejection, temperature grade, and supply limits. If adjustable gain, a smaller surface-mount footprint, or a lower-cost generic subtractor is more important, a different amplifier may be a better architectural choice. A true PCB replacement must also preserve the 8-pin PDIP footprint and pin functions; the identified INA105AM and INA105BM SOIC options do not satisfy that mechanical requirement.
與替代品比較
| 參數 | 本產品 | INA105KP |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP | 8-pin PDIP |
| Product Type | Precision unity-gain differential amplifier | Precision unity-gain differential amplifier |
| Gain | 1 V/V | 1 V/V |
| Bandwidth | 1 MHz | 1 MHz |
| Slew Rate | 3 V/us | 3 V/us |
| Minimum Supply Voltage | ±5 V | ±5 V |
| Internal Gain Network | Laser-trimmed metal-film resistor network | Laser-trimmed metal-film resistor network |
| Number of Amplifiers | 1 circuit | 1 circuit |
主要差異化特點
- Fixed unity gain is implemented with an internally trimmed resistor network (對比INA105KP)
- Differential measurement does not require an external gain-setting resistor network (對比INA105KP)
- Through-hole package simplifies inspection and prototype replacement (對比INA105AM)
設計說明
Use a symmetrical input layout and connect the two signal terminals with matched routing lengths and geometry. A differential amplifier converts mismatched impedance and unequal parasitic coupling into differential error, reducing common-mode rejection in exactly the precision measurements where the INA105's trimmed network is valuable. Keep the input traces away from supply switching nodes, relay contacts, and high-current return paths.
Check input common-mode voltage and output swing before finalizing the ±5 V minimum-supply design. A differential signal can still exceed the amplifier's permitted common-mode range even when its difference is small. Likewise, unity gain does not create output headroom. Confirm both rails against the worst-case input, output, and transient conditions rather than relying only on the nominal differential signal amplitude.
Place the supply-decoupling capacitors adjacent to the positive and negative supply pins, and provide a low-impedance return path from the circuit ground. Avoid connecting sensitive input returns through the same resistance shared with output loads. The through-hole DIP footprint is mechanically straightforward, but lead bending and socket cleanliness can affect precision measurements, so inspect contacts and maintain consistent soldering quality.
合規資訊
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified. AEC-Q100 is marked not applicable because the INA105KPG4 is a general-purpose precision amplifier rather than an automotive-qualified device.