Texas Instruments

INA105KPG4 - 1MHz Differential Amplifier | Texas Instruments

部品番号: INA105KPG4 ✓ 生産中
500 uV maximum Vdss 8-pin PDIP Package
MOQ: 1 |

INA105KPG4 概要

Texas Instruments INA105KPG4 is a precision unity-gain differential amplifier with a 1 MHz bandwidth and 3 V/us slew rate, packaged in an 8-pin PDIP. It combines a precision operational amplifier with an on-chip, laser-trimmed metal-film resistor network. The fixed unity gain is implemented on-chip, allowing the device to amplify the difference between two input voltages without an external gain-setting resistor.

A differential amplifier is a voltage-regulating amplifier that rejects a voltage common to both inputs while amplifying the difference between them. The INA105 belongs to the instrumentation-amplifier and differential-amplifier hierarchy, where precise resistor matching improves common-mode rejection and gain accuracy. This capability is useful when a small sensor or measurement signal must be extracted from a larger voltage that also drives the system.

The key feature of the INA105 is its internally trimmed, unity-gain network. Laser trimming establishes accurate gain and high common-mode rejection, while matched resistor temperature coefficients help maintain performance over changing temperature. The INA105KPG4 operates from a minimum dual supply of ±5 V. Its 1 MHz bandwidth supports signals extending from low-frequency instrumentation into audio and industrial control bandwidths, while the 3 V/us slew rate allows large signal changes without excessive distortion.

The monolithic construction simplifies differential measurement by eliminating the four external precision resistors normally associated with a unity-gain subtractor. It does not provide the adjustable gain available in higher-gain differential amplifier families, so applications requiring substantial gain should include an additional gain stage. Designers must also verify that signal and output voltages remain inside the amplifier's input and output common-mode limits.

Typical uses include bridge-transducer interfaces, current-shunt measurements, instrumentation front ends, industrial sensing, and differential signal conditioning. The fixed unity-gain relationship makes the device particularly suitable when the following circuit requires a balanced or translated differential result without an external resistor network.

For PCB implementation, treat the eight-pin PDIP as a through-hole precision analog component. Keep input and output traces short, connect decoupling capacitors close to the supply pins, and avoid routing high-current or switching-node copper near the input terminals. Verify reference-ground arrangements carefully because common-mode rejection depends on clean grounding and symmetric signal paths.

This page combines the manufacturer's device description with package, frequency, and slew-rate data, organized drop-in alternatives, comparison parameters, and practical circuit guidance. The technical sections help engineers evaluate the INA105KPG4 for precision differential measurements, identify sourcing options through the Request a Quote form, and plan a robust implementation without redundant datasheet navigation.

ドロップイン代替品: INA105KPG4 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: INA105KPG4 (同一形状・フットプリント) — 相違点: Mounting Type, Package, Product Type.

Texas Instruments
Mounting Type: Through-hole / DIP
Package: 8-pin PDIP (P package), through-hole
Product Type: Precision unity-gain differential amplifier (1 circuit)
比較対象 INA105KPG4 →

INA105KP

✅ ドロップイン
Texas Instruments
📦 PDIP-8
Precision unity-gain differential amplifier (1 circuit) · 1.000 (unity, fixed) · 1 MHz · 500 uV · 86 dB · 10 V to 36 V (single 5 V to 36 V, dual +/-5 V to +/-18 V) · -20 V

価格はお問い合わせください

データシートを見る →

INA105KPG4 最大定格&電気的特性

Product Type Precision unity-gain differential amplifier
Number of Amplifiers 1 circuit
Gain 1 V/V
Bandwidth 1 MHz
Slew Rate 3 V/us
Input Offset Voltage 500 uV maximum
Minimum Supply Voltage ±5 V
Internal Resistor Network Laser-trimmed metal-film resistors
パッケージ 8-pin PDIP
実装タイプ Through-hole
RoHS ステータス unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable
Safe Operating Area not applicable to this linear amplifier

INA105KPG4 8-pin pdip ピン配置ガイド

INA105KPG4 (8-pin pdip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。

INA105KPG4 の 8-pin pdip パッケージピン配置図

詳細なピン配置データはありません: INA105KPG4.

詳細は データシート をご参照ください。

主な用途

INA105KPG4 の用途: 6 件s: Bridge Transducer Interface, Current-Shunt Measurement, Industrial Sensor Signal Conditioning, Precision Instrumentation Front End, Audio-Range Differential Interface, Laboratory and Test Equipment.

🏭

Bridge Transducer Interface

The INA105KPG4 is suitable for conditioning the small differential output of a resistive bridge because its fixed unity gain preserves the bridge signal while its laser-trimmed internal network is designed for accurate gain and high common-mode rejection. The 500 uV maximum input offset specification is especially relevant when the transducer output is small. Place the amplifier close to the bridge and keep the two input routes geometrically similar to minimize conversion of common-mode interference into differential error.

⚡

Current-Shunt Measurement

For current-shunt monitoring, the INA105KPG4 can amplify the shunt's differential voltage without external unity-gain resistors. Its 1 MHz bandwidth accommodates many industrial control and diagnostic signals, while the 3 V/us slew rate permits fast changes in the measured current. The main design constraint is common-mode range: shunt voltage must remain within the amplifier's permitted input range, and Kelvin routing should connect the sense terminals directly to the amplifier.

🏭

Industrial Sensor Signal Conditioning

The INA105KPG4 fits industrial sensor front ends that present a differential output superimposed on a common-mode voltage. Its unity-gain topology and laser-trimmed resistor network reduce dependence on external resistor matching, while common-mode rejection helps isolate the desired sensor signal. With ±5 V minimum dual-supply operation, the device is appropriate for ±15 V or ±12 V instrumentation systems, subject to the input and output range limits stated in the manufacturer datasheet.

🖥️

Precision Instrumentation Front End

The INA105KPG4 can serve as the first differential stage in a precision instrumentation front end when unity gain is sufficient. Its 1 MHz bandwidth supports signal bandwidth beyond traditional slow industrial measurements, and the 500 uV maximum input offset establishes a useful baseline for low-level differential measurements. Use a grounded guard or shielding strategy when source impedance is high, and verify that output swing remains adequate before adding another gain stage.

🎧

Audio-Range Differential Interface

The INA105KPG4 is usable for audio-range differential interfaces when the system requires a fixed unity-gain differential transfer function and a 1 MHz bandwidth. The 3 V/us slew rate is adequate for many low-to-moderate amplitude audio signals, but distortion must be checked at the highest expected frequency and output level. The DIP package favors prototype and legacy equipment rather than compact consumer audio products, so the mechanical footprint should be considered before design selection.

🔧

Laboratory and Test Equipment

The INA105KPG4 is appropriate for laboratory differential input stages because its internal unity-gain network reduces the number of precision external components that must be selected and matched. The 1 MHz bandwidth supports many general-purpose waveform and instrumentation tasks, while the 3 V/us slew rate covers signals with moderate edge rates. For bench designs, place the device on a low-noise prototype area and verify source impedance, grounding, and output saturation before calibration.

What is the INA105KPG4?
The INA105KPG4 is a precision unity-gain differential amplifier with a 1 MHz bandwidth and 3 V/us slew rate in an 8-pin PDIP package. According to the Texas Instruments INA105 datasheet, it combines a precision operational amplifier with an on-chip, laser-trimmed metal-film resistor network. The internal network fixes the nominal gain at 1 V/V and is designed to provide accurate gain and high common-mode rejection without external gain-setting resistors.
What are the key specifications of INA105KPG4 that engineers should know?
The INA105KPG4 provides unity gain, a 1 MHz bandwidth, a 3 V/us slew rate, and a maximum input offset voltage of 500 uV in an 8-pin PDIP package. Texas Instruments describes the internal resistor network as laser trimmed for accurate gain and high common-mode rejection. The minimum operating supply is ±5 V, while the maximum supply and detailed input common-mode limits should be confirmed in the manufacturer datasheet before final circuit signoff.
Where can I download the INA105KPG4 datasheet PDF?
The official INA105KPG4 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ina105.pdf. The document describes the monolithic unity-gain differential amplifier, its precision operational amplifier, and the laser-trimmed on-chip resistor network. It is the preferred document for checking the complete electrical characteristics, input and output common-mode limits, supply range, pin description, and typical application circuit.
Where can I find the INA105KPG4 pinout?
The INA105KPG4 pinout is published in the pin-description section of the Texas Instruments INA105 manufacturer datasheet. The device is an 8-pin PDIP package, so the physical package has eight leads. Use the manufacturer drawing and pin-description table when assigning each PCB track because the device also includes supply, input, and differential-output functions that must not be interchanged during layout.
Does the INA105KPG4 need external gain-setting resistors?
No, the INA105KPG4 does not require external gain-setting resistors because its gain is fixed internally at 1 V/V. The Texas Instruments datasheet describes an on-chip metal-film resistor network that is laser trimmed for accurate gain and high common-mode rejection. This internal implementation is the main convenience of the device, although it also means the INA105 cannot provide a higher adjustable gain than its fixed unity ratio.
What is the bandwidth and slew rate of INA105KPG4?
The INA105KPG4 has a 1 MHz bandwidth and a 3 V/us slew rate. These figures describe its small-signal frequency response and maximum rate of output-voltage change, respectively. They make the amplifier suitable for low-frequency precision measurements, audio-range instrumentation, and industrial control signals. Confirm the signal amplitude and frequency together because large-signal operation can be limited by slew rate rather than small-signal bandwidth.
What supply voltage does INA105KPG4 require?
The INA105KPG4 requires a minimum dual supply of ±5 V for operation. The Texas Instruments product page identifies it as a precision unity-gain differential amplifier, while the device listing classifies it as a single-channel differential amplifier in an 8-pin PDIP. The upper supply limit and any single-supply operating conditions should be checked directly in the manufacturer datasheet before selecting the power rails.
Where to buy INA105KPG4 online?
The INA105KPG4 can be requested through the Request a Quote form on this page, which is the recommended channel for current unit availability, quantity, and lead-time confirmation. The manufacturer product page and authorized distribution listings identify the exact 8-pin PDIP device, but purchasing conditions and stock can change. Submit the required quantity, target package, and production schedule with the quote request.
What is the price of INA105KPG4?
The current price of INA105KPG4 should be obtained through the Request a Quote form on this page so the quoted result reflects the requested quantity and current availability. The structured offer data on this page tracks exact-MPN listing information separately from the quote workflow. No static price should be treated as a guaranteed procurement quotation because market conditions and order quantity affect the result.
What is the lead time for INA105KPG4?
The current lead time for INA105KPG4 should be confirmed through the Request a Quote form on this page. When requesting the quote, state the required quantity, date code preference, and whether the 8-pin PDIP package is acceptable. The manufacturer product page confirms the device family and ordering information, but firm production timing must be established for the particular order.
Is INA105KPG4 in stock?
Current INA105KPG4 inventory should be checked through the Request a Quote form on this page because availability can change with order quantity and replenishment timing. The exact orderable identifier is INA105KPG4, corresponding to the Texas Instruments 8-pin PDIP package. Request a written confirmation of stock, lead time, and assembly lot requirements before committing the component to a production schedule.
What is the best drop-in replacement for INA105KPG4?
INA105KP is the closest identified same-package replacement because it belongs to the INA105 unity-gain family and uses the 8-pin PDIP configuration, while INA105KPG4 adds the G4 orderable suffix. A replacement should still be checked for gain tolerance, common-mode rejection, offset voltage, supply limits, temperature range, and lifecycle status. Only one genuine same-package candidate was established, and package-equivalent SOIC variants are not drop-in replacements for a PDIP PCB footprint.
Can INA105KP replace INA105KPG4 without PCB changes?
INA105KP can serve as a replacement candidate without changing the eight-pin PDIP footprint because it is identified in INA105 family comparison material, while INA105KPG4 uses the same package with an additional orderable suffix. Final interchangeability still depends on matching temperature grade, supply range, offset, gain accuracy, common-mode rejection, and qualification requirements. Review the current Texas Instruments ordering information before treating the parts as production equivalents.
INA105KPG4 vs INA105KP — which is better for a precision bridge circuit?
Choose INA105KPG4 when its exact ordering qualifications and temperature grade match a production bridge circuit; otherwise INA105KP may be the simpler same-family candidate. Both devices provide the core INA105 unity-gain differential-amplifier function in an 8-pin PDIP package. The decisive issues are not nominal gain but guaranteed offset, common-mode rejection, supply limits, temperature range, and exact orderable status.
When should I choose INA105KPG4 over a generic differential amplifier?
Choose INA105KPG4 when a fixed 1 V/V differential gain, 1 MHz bandwidth, and internally trimmed resistor network are more valuable than adjustable gain or a different package. Its 3 V/us slew rate and 500 uV maximum input offset support precision signal conditioning, while the 8-pin PDIP simplifies through-hole prototypes and legacy-style assemblies. A generic amplifier may be preferable when gain adjustment, smaller packaging, or lower cost is the dominant requirement.
What is the best Analog Devices equivalent for INA105KPG4?
The cross-reference search identifies Analog Devices as a manufacturer with an INA105 replacement, but the supplied result does not name the exact Analog Devices orderable part or confirm its package and pin map. It therefore cannot be represented as a verified drop-in alternative. Use the Texas Instruments cross-reference search and the candidate's own datasheet to confirm an 8-pin PDIP footprint, unity-gain pinout, supply range, common-mode limits, and electrical performance before substituting it.

エンジニアリング参考データ: INA105KPG4 — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose INA105KPG4 for precision differential measurements that specifically require a unity-gain, through-hole Texas Instruments implementation with 1 MHz bandwidth and 3 V/us slew rate. It is especially useful when the signal source is a bridge, shunt, or balanced sensor and an external gain-setting network is undesirable. INA105KP is the closest identified same-family, same-package alternative when the exact orderable suffix and qualification details are acceptable.

Do not select the INA105 family solely by its 1 MHz bandwidth. First confirm common-mode range, output swing, offset voltage, common-mode rejection, temperature grade, and supply limits. If adjustable gain, a smaller surface-mount footprint, or a lower-cost generic subtractor is more important, a different amplifier may be a better architectural choice. A true PCB replacement must also preserve the 8-pin PDIP footprint and pin functions; the identified INA105AM and INA105BM SOIC options do not satisfy that mechanical requirement.

代替品との比較

パラメータ この製品 INA105KP
Brand Texas Instruments Texas Instruments
Package 8-pin PDIP 8-pin PDIP
Product Type Precision unity-gain differential amplifier Precision unity-gain differential amplifier
Gain 1 V/V 1 V/V
Bandwidth 1 MHz 1 MHz
Slew Rate 3 V/us 3 V/us
Minimum Supply Voltage ±5 V ±5 V
Internal Gain Network Laser-trimmed metal-film resistor network Laser-trimmed metal-film resistor network
Number of Amplifiers 1 circuit 1 circuit

主な差別化要因

  • Fixed unity gain is implemented with an internally trimmed resistor network (vs INA105KP)
  • Differential measurement does not require an external gain-setting resistor network (vs INA105KP)
  • Through-hole package simplifies inspection and prototype replacement (vs INA105AM)

設計ノート

Use a symmetrical input layout and connect the two signal terminals with matched routing lengths and geometry. A differential amplifier converts mismatched impedance and unequal parasitic coupling into differential error, reducing common-mode rejection in exactly the precision measurements where the INA105's trimmed network is valuable. Keep the input traces away from supply switching nodes, relay contacts, and high-current return paths.

Check input common-mode voltage and output swing before finalizing the ±5 V minimum-supply design. A differential signal can still exceed the amplifier's permitted common-mode range even when its difference is small. Likewise, unity gain does not create output headroom. Confirm both rails against the worst-case input, output, and transient conditions rather than relying only on the nominal differential signal amplitude.

Place the supply-decoupling capacitors adjacent to the positive and negative supply pins, and provide a low-impedance return path from the circuit ground. Avoid connecting sensitive input returns through the same resistance shared with output loads. The through-hole DIP footprint is mechanically straightforward, but lead bending and socket cleanliness can affect precision measurements, so inspect contacts and maintain consistent soldering quality.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified. AEC-Q100 is marked not applicable because the INA105KPG4 is a general-purpose precision amplifier rather than an automotive-qualified device.

関連検索

INA105KPG4 datasheet INA105KPG4 datasheet pdf INA105KPG4 pinout INA105KPG4 specifications INA105KPG4 equivalent INA105KPG4 replacement INA105KPG4 cross reference INA105KPG4 vs INA105KP INA105KPG4 price INA105KPG4 stock Texas Instruments INA105KPG4 INA105KPG4 1MHz differential amplifier INA105KPG4 PDIP-8 pinout INA105KPG4 bridge sensor interface

関連部品&用語

Texas Instruments INA105KPG4 INA105KP INA105 precision differential amplifier instrumentation amplifier differential amplifier operational amplifier unity-gain amplifier metal-film resistor network laser trimming common-mode rejection input offset voltage gain accuracy 1 MHz bandwidth 3 V/us slew rate PDIP-8 DIP package through-hole mounting bridge transducer current-shunt measurement industrial sensor signal conditioning instrumentation front end semiconductor
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示