ISL8487EIB - 5V RS-485/RS-422 Transceiver | Renesas
MPN: ISL8487EIB ✓ 啟用中ISL8487EIB 概覽
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential, balanced bus signals and receives differential bus signals back into CMOS-compatible logic. The differential architecture improves common-mode noise rejection and supports communication over longer cables than single-ended interfaces. The ISL8487E belongs to the RS-485 transceiver hierarchy, within interface ICs and broader data-communication semiconductors.
Key characteristics include ±15 kV ESD protection, fractional 1/8-unit loading, 5 V operation, and a maximum quiescent current of 145 µA for the ISL8487E family. The fractional loading permits as many as 256 devices on a bus under ideal conditions, subject to the network configuration and system-level constraints. Both high-speed and slew-rate-limited versions appear in the ISL8487E family, so the exact drive and data-rate limits should be confirmed from the ISL8487E datasheet before selecting the required speed grade.
The BiCMOS implementation combines low power with balanced-line drive capability. The receiver can monitor bus activity independently of the driver, while the driver and receiver enables support controlled connection to a multidrop network. The ±15 kV protection is particularly useful in industrial environments where cables may connect to external equipment and exposed connectors.
Typical applications include industrial process automation, remote meter reading, building controls, factory equipment links, multidrop instrumentation buses, and point-to-point RS-422 links. The low 1/8-unit load is valuable when many nodes share one bus, while the small SOIC-8 package simplifies PCB routing in compact control equipment.
When laying out the circuit, route the differential A and B traces as a closely coupled pair, provide the transceiver-side decoupling recommended by the manufacturer datasheet, and use chassis-ground protection methods at exposed connectors. Termination remains a network-level decision: terminate the far ends of the bus rather than every node, and confirm whether the selected family member uses slew-rate-limited or high-speed drive.
This page combines the manufacturer family specifications, package and interface details, comparison guidance, and practical PCB considerations to accelerate transceiver selection for balanced industrial communication links.
直接替換替代品,適用於 ISL8487EIB — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MAX1483ESA+T
✅ 直接替換📋 參考替代品(不在目錄中)
ISL8487EIB 規格
| Product Type | Single RS-485/RS-422 transceiver |
| Number of Transceivers | 1 transceiver |
| 供應電壓 | 5 V |
| Driver and Receiver Count | 1 driver and 1 receiver |
| Interface Standards | RS-485 and RS-422 |
| ESD Protection | ±15 kV on each driver output and receiver input |
| Receiver Unit Load | 1/8 unit load |
| Maximum Bus Devices | Up to 256 devices under ideal fractional-load conditions |
| 靜態電流 | 145 µA maximum for the ISL8487E family |
| Technology | BiCMOS |
| 資料速率 | Up to 250 kbps for slew-rate-limited family members |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| Product Variant | ISL8487EIB industrial-temperature designation |
| RoHS 狀態 | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Not applicable |
| Lead-Free Status | Unknown |
ISL8487EIB 8-pin soic 腳位配置指南
ISL8487EIB(8-pin soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ISL8487EIB.
請參閱 資料表 以查看完整腳位配置。
典型應用
ISL8487EIB 適用於 6 應用s: Industrial Process Automation, Remote Meter Reading, Building Automation Networks, Factory Equipment Communication, RS-422 Point-to-Point Link, Multipoint Instrumentation Bus.
Industrial Process Automation
The ISL8487EIB fits controller-to-instrument links in process automation because it combines a 5 V supply, differential RS-485/RS-422 operation, and ±15 kV ESD protection on the external bus pins. The 1/8-unit receiver load allows a dense network of up to 256 devices under ideal fractional-load conditions. Place the transceiver between the logic controller and the A/B bus, enable the driver only while transmitting, and use coupled differential routing to preserve noise immunity. Its low quiescent current, up to 145 µA for the family, also benefits compact remote I/O modules.
推薦
Remote Meter Reading
The ISL8487EIB is appropriate for remote meter-reading concentrators that collect measurements from many low-power field devices over a multidrop bus. Its 1/8-unit receiver load minimizes loading of the shared line, while the 5 V operation simplifies interface design in battery- and solar-powered instruments. The transceiver converts the metering controller’s logic signal into a differential bus waveform and returns bus data to the controller. Place ESD protection near external connectors and route the A and B traces together to retain common-mode rejection over the cable run.
推薦
Building Automation Networks
The ISL8487EIB supports balanced communication links used by building automation controllers, sensors, and access equipment. Its RS-485/RS-422 capability provides noise-resistant signaling, while the 1/8-unit receiver load helps accommodate multiple nodes on a shared cable. The ±15 kV ESD protection on driver outputs and receiver inputs adds defense when the bus connects to equipment or building wiring outside the enclosure. Firmware must manage driver-enable timing to prevent multiple transmitters from driving the bus simultaneously, and cable termination should be installed only where the network design requires it.
推薦
Factory Equipment Communication
The ISL8487EIB is suitable for factory equipment links where motors, contactors, and long cables can introduce electrical transients and common-mode noise. The differential A/B interface rejects much of this interference, and ±15 kV ESD protection improves robustness at cable-facing pins. Use the transceiver in a remote I/O board to isolate a central controller from equipment located across the production floor. Keep the differential pair tightly coupled, avoid routing it alongside high-current switching paths, and provide local supply bypassing according to the manufacturer application circuit.
推薦
RS-422 Point-to-Point Link
The ISL8487EIB can be used for point-to-point RS-422 communication between two pieces of equipment when the system requires balanced signaling and protection at the line interface. A single transceiver provides one driver and one receiver, allowing full-duplex point-to-point links when paired with another transceiver at the remote endpoint. Its 5 V supply and 1/8-unit receiver load make it practical for compact interface cards. Verify the exact family member’s maximum data rate, propagation delay, and output-load capability against the required cable length before production release.
推薦
Multipoint Instrumentation Bus
The ISL8487EIB fits multipoint instrumentation networks because its fractional 1/8-unit receiver load supports as many as 256 devices under ideal bus conditions. This loading capability is valuable when laboratory, utility, or industrial monitoring systems distribute multiple sensors and measurement modules along one cable. The transceiver’s balanced I/O improves noise immunity, while ±15 kV ESD protection strengthens the interface against external cable-borne events. Use disciplined driver-enable control so only one node transmits at a time, and apply termination at the physical endpoints of the bus rather than at every instrument.
推薦
推薦產品摘要
工程參考資料,適用於 ISL8487EIB — 比較、設計指引及合規資訊。
選型指南
Evaluate MAX1483ESA+T when its approximately 20 µA operating current is advantageous or when its documented slew-rate-limited behavior is preferred for a lower-rate network. Although both devices use an 8-pin SOIC-style package and offer 1/8-unit loading, do not approve a substitution without checking pin functions, enable polarity, propagation timing, receiver behavior, ESD rating, temperature range, and package dimensions. For point-to-point RS-422, multidrop RS-485, or any mixed industrial installation, validate the complete bus and termination strategy rather than judging only by pin count.
與替代品比較
| 參數 | 本產品 | MAX1483ESA+T |
|---|---|---|
| Package | 8-pin SOIC | 8-pin NSOIC |
| Brand | Renesas Electronics | Maxim Integrated |
| Transceiver Count | 1 | 1 |
| Supported Interfaces | RS-485 and RS-422 | RS-485 and RS-422 |
| Supply Voltage | 5 V | 5 V |
| Receiver Unit Load | 1/8 unit load | 1/8 unit load |
| Operating Current | 145 µA maximum quiescent current for the ISL8487E family | 20 µA |
| Driver Edge Behavior | High-speed or slew-rate-limited family options | Slew-rate limited |
主要差異化特點
- Documented ESD protection on every external line pin (對比MAX1483ESA+T)
- Family supports high-speed and slew-rate-limited drive options (對比MAX1483ESA+T)
- Multidrop loading supports up to 256 ideal-condition devices (對比MAX1483ESA+T)
設計說明
Route A and B as a tightly coupled differential pair from the transceiver to the connector or isolation boundary. Match their geometry where practical, avoid splits or stubs, and keep the pair away from switching-node and high-current return paths. Place the transceiver close to the cable-facing protection components so transient current is diverted before reaching sensitive circuitry. Follow the manufacturer recommended-decoupling and exposed-side layout guidance for the 8-pin SOIC.
Termination is a network property rather than a requirement for every node. For conventional RS-485, place termination resistors at the two physical ends of the bus and confirm the resistor value against the transceiver documentation and cable impedance. Slew-rate-limited family members reduce edge-rate-related EMI and ringing, but the exact ISL8487E variant and its data-rate limit must still be checked before using that behavior as a substitute for correct topology.
Do not enable multiple bus drivers simultaneously. Firmware or hardware logic should grant the transmitter permission only after the controller has completed reception and should provide adequate turnaround time for a multidrop bus. Also verify that the replacement transceiver’s enable polarity, receiver-output state, propagation delay, and fail-safe behavior match the original design; identical SOIC-8 packages alone do not establish functional interchangeability.
Keep external cable wiring away from sensitive analog and clock paths, and use the chassis or shield as the return path for common-mode surge energy where the system design permits it. The family’s ±15 kV ESD protection helps at driver outputs and receiver inputs, but it does not replace a complete board-level surge and ESD strategy. Keep unprotected external conductors away from the IC and use the protection network shown in the manufacturer application material.
合規資訊
The manufacturer family datasheet confirms ESD protection and BiCMOS construction but the product records do not explicitly establish RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for the exact ISL8487EIB ordering code.