KSZ8873RLLU - 3-Port 10/100 Ethernet Switch | Microchip
MPN: KSZ8873RLLU ✓ 啟用中KSZ8873RLLU 概覽
An Ethernet switch is a network-interface integrated circuit that receives frames on one or more physical ports and forwards them to other ports using MAC addresses. Within the network hierarchy, the KSZ8873 is a three-port Layer 2 switch, while its integrated 10/100 Base-TX PHYs connect directly to copper Ethernet cabling without requiring separate transceiver components. Its small footprint suits compact industrial controllers, embedded gateways, and cost-sensitive access equipment.
Key features include three integrated 10/100 Mbps ports, IEEE 802.3u Fast Ethernet operation, and both I2C and SPI host interfaces. Configuration access allows the host processor to manage switch behavior, address tables, and port parameters. The RLLU ordering designation identifies the 64-LQFP package configuration, while the U suffix denotes the supplied packaging arrangement for production assembly.
The KSZ8873 family is intended to reduce board area by consolidating multiple PHY functions and switch control into one device. This lowers component count and simplifies routing compared with discrete Ethernet controllers, although each copper port still requires external magnetics, line-side filtering, and a properly terminated RJ45 interface. The integrated PHYs do not replace Ethernet transformers or the connector's isolation requirements.
Typical applications include industrial Ethernet bridges, embedded control panels, set-top and access equipment, printer controllers, machine vision systems, and compact network appliances. Each port must be checked against the system's link-speed, cable-length, and auto-negotiation requirements. Designers should also review the manufacturer reference schematic for recommended magnetics and impedance-controlled differential routing.
A key design consideration is the relationship between switching performance and copper-magnetics selection. Although the switch provides 10/100 Mbps data paths, board-level EMI and return-loss performance depend on the transformer, center-tap termination, Bob Smith termination, and controlled-impedance layout. Review the pin-description and layout guidance in the Microchip KSZ8873 datasheet before assigning PCB nets.
This page consolidates package information, interface details, family substitution guidance, and application-oriented design guidance. It also identifies the electrical and layout parameters that require confirmation from the manufacturer datasheet before a new PCB is released.
直接替換替代品,適用於 KSZ8873RLLU — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: KSZ8873RLLU (相同外形與佔位) — 差異在於 Package, Product Type, Host Interface, Ethernet Data Rate, Operating Temperature Range.
KSZ8873MLL
✅ 直接替換聯絡詢價
查看資料表 →KSZ8873FLL
✅ 直接替換聯絡詢價
查看資料表 →KSZ8873RLL
✅ 直接替換聯絡詢價
查看資料表 →KSZ8873RLLI
✅ 直接替換聯絡詢價
查看資料表 →KSZ8873RLLU 最大額定值與電氣特性
| Device Type | 3-port Ethernet switch with integrated 10/100 Base-TX PHYs |
| Number of Ports | 3 ports |
| 資料速率 | 10/100 Mbps per port |
| Ethernet Standard | IEEE 802.3u |
| Supply Voltage Range | 1.66 V to 3.465 V |
| Host Interface | I2C and SPI |
| 封裝 | 64-LQFP, 10 x 10 mm |
| 安裝類型 | Surface mount |
| 工作溫度範圍 | -40°C to +85°C |
| Temperature Grade | Extended temperature |
| Port Count | 3 integrated Fast Ethernet ports |
| Media Support | 10/100 Base-TX copper Ethernet |
| Product Family | KSZ8873MML/MLL/FLL/RLL |
| Interface Control | I2C or SPI host configuration |
| Switch Function | Integrated Layer 2 Ethernet switching |
KSZ8873RLLU 64-lqfp, 10 x 10 mm 腳位配置指南
KSZ8873RLLU(64-lqfp, 10 x 10 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: KSZ8873RLLU.
請參閱 資料表 以查看完整腳位配置。
典型應用
KSZ8873RLLU 適用於 6 應用s: Industrial Ethernet Bridge, Embedded Network Appliance, Machine Vision Controller, Printer and Imaging Controller, Set-Top and Access Equipment, Building and Energy Control Gateway.
Industrial Ethernet Bridge
The KSZ8873RLLU suits a compact industrial bridge that must distribute 10/100 Mbps copper links among sensors, a controller, and an upstream gateway. Its three integrated PHYs avoid the area and routing overhead of three discrete network interfaces, while I2C or SPI allows the host processor to configure the switch. Because the device operates from 1.66 V to 3.465 V, it can share a low-voltage industrial system rail. External isolation magnetics, controlled-impedance routing, and EMI filtering remain essential to achieve reliable copper links in industrial cabinets.
推薦
Embedded Network Appliance
A compact gateway, controller, or print server can use the KSZ8873RLLU to provide three 10/100 Mbps service ports without adding separate PHY packages. Its 64-LQFP 10 x 10 mm footprint preserves routing space in densely populated boards, and the extended -40°C to +85°C range supports industrial and harsh indoor equipment. The host processor selects configuration through I2C or SPI, simplifying firmware access to switch functions. Engineers must still reserve space for RJ45 connectors, isolation transformers, and the recommended termination network around every copper port.
推薦
Machine Vision Controller
The KSZ8873RLLU can connect a machine-vision controller to cameras, a vision server, and service equipment over separate 10/100 Mbps copper ports. Integrating the PHYs into one switch reduces the number of high-speed copper routing regions and keeps the control board compact. I2C management is useful when the host bus is already occupied, while SPI provides a higher-speed alternative for initialization. The 1.66 V to 3.465 V operating range supports low-voltage embedded platforms, but camera links may require careful isolation, return-loss, and EMI layout based on the chosen magnetics.
推薦
Printer and Imaging Controller
Printers, copiers, and imaging peripherals often need several 10/100 Mbps ports for service, host, and configuration links. The KSZ8873RLLU consolidates those copper interfaces into one 64-LQFP device and provides I2C or SPI control from the embedded printer controller. Its low-port-count architecture is appropriate for cost-sensitive equipment that does not require gigabit Ethernet. Designers should use the manufacturer layout guidance to route the PHY differential pairs cleanly and should verify transformer selection against the required cable length and emission targets.
推薦
Set-Top and Access Equipment
Compact set-top boxes and access equipment benefit from the KSZ8873RLLU's three integrated Fast Ethernet ports and small 64-LQFP footprint. The switch supports 10/100 Mbps service connectivity for IP television, management, or service-diagnostic functions without relying on several discrete Ethernet controllers. Its 1.66 V to 3.465 V supply range allows deployment alongside modern application processors, and I2C or SPI management keeps host integration straightforward. The enclosure still requires tested magnetics and filtering, since component integration alone does not guarantee regulatory EMI performance.
推薦
Building and Energy Control Gateway
The KSZ8873RLLU is suitable for low-cost building controllers, energy-monitoring gateways, and HVAC interface modules that connect several 10/100 Mbps devices. Three integrated PHYs support controller, upstream, and service links, while the -40°C to +85°C operating range suits equipment beyond ordinary consumer temperatures. Host configuration through I2C or SPI simplifies integration with a microcontroller or application processor. Because these products may be installed near long cables or noisy power systems, the Ethernet magnetics, return-loss structure, and chassis grounding must be evaluated as part of the complete interface design.
推薦
推薦產品摘要
工程參考資料,適用於 KSZ8873RLLU — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | KSZ8873MLL | KSZ8873FLL | KSZ8873RLL | KSZ8873RLLI |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-LQFP (10x10) | 64-LQFP (10x10) | 64-LQFP (10x10) | 64-LQFP (10x10) | 64-LQFP (10x10) |
| Device Type | 3-port Ethernet switch | KSZ8873 family switch | KSZ8873 family switch | 3-port Ethernet switch | KSZ8873 family switch |
| Ethernet Data Rate | 10/100 Mbps | 10/100 Mbps family | 10/100 Mbps family | 10/100 Mbps | 10/100 Mbps |
主要差異化特點
- Three copper-network ports integrated in one device (對比KSZ8873MLL)
- Dual host-control options on the same family (對比KSZ8873FLL)
- Compact 10 x 10 mm surface-mount implementation (對比KSZ8873RLL)
設計說明
Route PHY differential pairs as short, continuous, impedance-controlled traces and follow the Microchip KSZ8873 reference layout. Keep the switching and magnetics area away from noisy clock and power-conversion circuitry. Place the required bypass capacitors close to their specified supply pins and keep copper termination clear of unrelated digital return paths.
Validate the complete Ethernet interface, including the selected isolation transformer, termination components, RJ45 connector, and chassis strategy. Component placement and return-loss performance determine whether the 10/100 Mbps link is robust in the final enclosure. Use the manufacturer reference schematic and layout examples when creating the first revision rather than treating the IC footprint as a complete Ethernet design.
Do not substitute an ordering code solely because the 64-LQFP outline matches. Compare the KSZ8873MLL, KSZ8873FLL, KSZ8873RLL, and KSZ8873RLLI pin descriptions, temperature grades, and supported switch functions. Confirm unused interface handling and initialization requirements in the manufacturer documentation before releasing a substitution into production.
Design the 1.66 V to 3.465 V supply rails so each port remains within its operating limit under the intended load and startup sequence. Use the datasheet current limits to determine supply capacity and the recommended decoupling values for transient performance. Account for the switching load of all three ports rather than sizing the rail from an idle measurement.
合規資訊
The manufacturer product page confirms the KSZ8873 family and RLL ordering option, but no explicit RoHS, REACH, halogen-free, or conflict-minerals statements are included in the available records. AEC-Q100 is not applicable because this is a commercial Ethernet switch rather than an automotive-qualified device.