LAN8720AI-CP-ABC - 10/100 Ethernet PHY | Microchip
MPN: LAN8720AI-CP-ABC ✓ 啟用中LAN8720AI-CP-ABC 概覽
An Ethernet PHY is the physical-layer component that translates digital data from an Ethernet media-access controller into signals that can traverse a twisted-pair network. In the hierarchy of network semiconductors, the PHY operates below the Ethernet MAC and above the transformer, magnetics, connector, and cable. The RMII interface reduces the number of signals required between the PHY and the host controller, making the LAN8720AI-CP-ABC suitable for compact embedded systems with limited connector and routing resources.
Key features include full-duplex 10BASE-T and 100BASE-TX operation, automatic speed and duplex negotiation, HP Auto-MDIX support, and operation from 1.8 V, 2.5 V, or 3.3 V supplies. IEEE 802.3-2005-compliant register functions are supported alongside vendor-specific registers. These features allow the PHY to connect to an RMII-based microcontroller or dedicated Ethernet controller without requiring a separate manual speed configuration.
The LAN8720AI-CP-ABC integrates the digital transceiver, analog transmit and receive channels, clock recovery, and auto-negotiation functions into one package. Its 24-SQFN footprint supports high-density PCB layouts, while the exposed thermal pad provides a direct heat-transfer path. The interface is designed for host systems operating at 50 MHz RMII reference-clock frequency, which simplifies synchronization with common embedded Ethernet media-access controllers.
Typical applications include industrial Ethernet controllers, embedded IoT gateways, factory automation equipment, network-connected sensors, compact embedded Linux systems, and consumer or communications equipment with a 10/100 Ethernet link. The PHY is particularly useful when the design requires wired networking but must limit board area, interface pin count, and power consumption compared with a larger Ethernet transceiver implementation.
Layout quality is critical because high-speed digital and analog signals share the same package. Place the PHY close to the Ethernet magnetics and connector, keep the RMII clock and data traces short, provide clean supply decoupling, and follow the manufacturer’s reference layout for the exposed pad and mixed-signal return paths. This page combines package and interface guidance with practical replacement analysis for design reviews and sourcing.
The manufacturer identifies the LAN8720A family as active and distinguishes extended-commercial and industrial temperature options. For new designs, confirm the exact ordering code, package, thermal grade, and RMII implementation against the current manufacturer datasheet before releasing production artwork.
直接替換替代品,適用於 LAN8720AI-CP-ABC — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LAN8720AI-CP-ABC (相同外形與佔位) — 差異在於 Auto-MDIX, Package, Product Type.
LAN8720A-CP-ABC
✅ 直接替換📋 參考替代品(不在目錄中)
KSZ8081RNACA
✅ 直接替換聯絡詢價
查看資料表 →LAN8720AI-CP-ABC 規格
| Product Type | 10/100 Ethernet PHY transceiver |
| Supported Data Rates | 10 Mbps and 100 Mbps |
| Ethernet Standards | 10BASE-T and 100BASE-TX |
| Host Interface | RMII |
| Duplex Support | Full-duplex |
| Operating Supply Voltages | 1.8 V, 2.5 V, or 3.3 V |
| RMII Reference Clock | 50 MHz |
| Auto-Negotiation | Automatic speed and duplex selection |
| Auto-MDIX | HP Auto-MDIX supported |
| Register Compatibility | IEEE 802.3-2005-compliant and vendor-specific registers |
| 工作溫度範圍 | -40°C to 85°C |
| 封裝 | 24-SQFN, 4 x 4 mm |
| 腳位數 | 24 pins |
| 安裝類型 | Surface mount |
| Power Technology | Microchip flexPWR technology |
| Exposed Thermal Pad | Present |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | unknown |
LAN8720AI-CP-ABC 24-sqfn, 4 x 4 mm 腳位配置指南
LAN8720AI-CP-ABC(24-sqfn, 4 x 4 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: LAN8720AI-CP-ABC.
請參閱 資料表 以查看完整腳位配置。
典型應用
LAN8720AI-CP-ABC 適用於 6 應用s: Industrial Embedded Ethernet Gateway, IoT Sensor and Controller Hub, Networked Factory Automation Equipment, Compact Network Appliance, Industrial Test and Measurement Instrument, Robotics and Autonomous Equipment.
Industrial Embedded Ethernet Gateway
The LAN8720AI-CP-ABC fits industrial embedded gateways because it combines 10BASE-T/100BASE-TX operation, a standard 50 MHz RMII interface, and an industrial -40°C to 85°C temperature rating. It can sit between a microcontroller or application processor and an Ethernet transformer, providing automatic speed and duplex negotiation without manual interface configuration. HP Auto-MDIX also allows the design to accept direct or crossover connections, which simplifies field cabling. The compact 24-SQFN 4 x 4 mm package preserves board area for sensing, storage, and communications functions. Designers should place the PHY close to the magnetics, maintain short RMII routes, and use the manufacturer’s exposed-pad and mixed-signal layout guidance to limit insertion loss and coupling between clock, data, and analog network circuitry.
推薦
IoT Sensor and Controller Hub
The LAN8720AI-CP-ABC is useful in an IoT sensor hub that adds wired Ethernet to a microcontroller-based product while retaining a small PCB footprint. Its RMII host connection limits the number of high-speed signals between the network PHY and controller, while 10 Mbps and 100 Mbps support allows shared industrial or building networks to be used without demanding gigabit PHY complexity. Automatic negotiation and HP Auto-MDIX improve installation robustness by adapting to link partners and cable arrangements. The 1.8 V, 2.5 V, and 3.3 V operating options can support multiple embedded power domains, but each rail must be checked against the manufacturer’s operating limits and decoupling recommendations. Ethernet magnetics and surge protection remain essential at the external network boundary.
推薦
Networked Factory Automation Equipment
LAN8720AI-CP-ABC supports factory automation modules that require deterministic wired-network connectivity over a -40°C to 85°C operating range. A 100BASE-TX link provides sufficient bandwidth for supervisory data, configuration traffic, status reporting, and industrial protocol gateways while reducing software and board complexity compared with a larger multi-interface Ethernet solution. The standard RMII interface supports integration with embedded controllers that provide a 50 MHz reference clock, while auto-negotiation removes manual speed configuration from field commissioning. Layout remains the primary implementation risk because the PHY, digital host interface, analog receive path, and Ethernet transformer share a small area. Follow the manufacturer’s reference layout, preserve short clock traces, provide local bypass capacitance, and keep copper and return paths away from the magnetics when the enclosure also contains high-power switching circuitry.
推薦
Compact Network Appliance
The LAN8720AI-CP-ABC can add a 10/100 Ethernet port to a compact appliance such as a building controller, access terminal, or embedded Linux gateway. Its 24-SQFN footprint is particularly useful where connector placement and board area are constrained. Because the PHY communicates through RMII rather than a parallel MII interface, the host design can reduce routing requirements and connector pressure on the processor. Automatic negotiation, full-duplex operation, and HP Auto-MDIX improve interoperability with office and industrial network equipment. The device can operate with 1.8 V, 2.5 V, or 3.3 V supplies, giving designers flexibility when coordinating processor, memory, and sensor rails. The physical Ethernet port still needs suitable isolation magnetics, a compliant connector path, and ESD protection rated for the installation environment.
推薦
Industrial Test and Measurement Instrument
LAN8720AI-CP-ABC is appropriate for test and measurement instruments that need a compact Ethernet management or data link. A 100BASE-TX connection can carry instrument status, configuration commands, and sampled results without consuming the larger FPGA or processor resources associated with a high-speed Ethernet PHY. The industrial temperature range allows use in equipment intended for controlled but thermally variable environments, while the RMII interface provides a defined connection to embedded control logic. Stable 50 MHz clocking and clean supply decoupling are essential for reliable data transfer and link training. Place the PHY near the transformer and connector, avoid routing RMII signals through noisy power-converter regions, and use the manufacturer’s recommended capacitor values and reference layout to minimize EMC and ESD-related failures at the external port.
推薦
Robotics and Autonomous Equipment
The LAN8720AI-CP-ABC can provide wired Ethernet connectivity in robot controllers, autonomous mobile equipment, and machine-vision nodes where a compact interface and broad temperature capability are valuable. The industrial -40°C to 85°C range supports equipment exposed to variable enclosure temperatures, while the 4 x 4 mm 24-SQFN package leaves room for motion-control and sensor circuitry. A 100BASE-TX link is appropriate for supervisory communication, diagnostics, configuration, and non-real-time telemetry. The PHY should be separated as much as practical from motor drivers and switching power stages, and the RMII clock must be routed as a controlled, well-referenced signal. Ethernet magnetics, surge protection, chassis grounding, and careful cable-entry design are especially important in mobile or industrial installations where cables can receive mechanical stress and electrostatic discharge.
推薦
推薦產品摘要
工程參考資料,適用於 LAN8720AI-CP-ABC — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LAN8720A-CP-ABC | KSZ8081RNACA |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 24-SQFN, 4 x 4 mm | 24-SQFN, 4 x 4 mm | 24-QFN, 4 x 4 mm |
| Supported Speeds | 10 Mbps and 100 Mbps | 10 Mbps and 100 Mbps | 10 Mbps and 100 Mbps |
| Host Interface | RMII | RMII | RMII |
| Operating Supply Voltages | 1.8 V, 2.5 V, or 3.3 V | 1.8 V, 2.5 V, or 3.3 V | 1.8 V, 2.5 V, or 3.3 V |
| Auto-MDIX | HP Auto-MDIX supported | HP Auto-MDIX supported | Auto-MDIX supported |
| Auto-Negotiation | Automatic speed and duplex selection | Automatic speed and duplex selection | Automatic speed and duplex selection |
主要差異化特點
- Broader industrial temperature coverage (對比LAN8720A-CP-ABC)
- Same compact package family for PCB reuse (對比LAN8720A-CP-ABC)
- Low-power industrial Ethernet integration (對比KSZ8081RNACA)
設計說明
Place LAN8720AI-CP-ABC close to the Ethernet transformer and connector, and route the analog network signals as short and symmetrical as practical. The RMII clock must arrive at the PHY with a clean reference and controlled return path; avoid crossings with switching-node or high-current supply traces. Use the manufacturer’s land pattern and exposed-pad geometry rather than a generic 24-QFN footprint because pad dimensions and thermal-via requirements can differ.
Provide local bypass capacitance at every supply connection exactly as specified in the manufacturer’s reference circuit, and keep the supply and ground paths short. The PHY supports 1.8 V, 2.5 V, and 3.3 V operating conditions, but the selected rail must satisfy the device’s voltage, timing, and power requirements under every operating mode. Validate startup, link training, and recovery from power cycling when the host controller and PHY use independently sequenced supplies.
Treat the 50 MHz RMII clock as the most timing-sensitive host-interface signal. Route it over a continuous reference plane, minimize stubs, maintain consistent spacing from switching signals, and observe the manufacturer’s clock-output and input-circuit recommendations. Confirm reset polarity, clock-source ownership, and valid operating states in software; identical Ethernet functionality does not guarantee identical reset or interrupt behavior across replacement devices.
Use the application circuit in the manufacturer datasheet for Ethernet magnetics, termination, link-up behavior, and network-side filtering. The Ethernet connector is an external ESD and surge entry point, so place protection at the boundary and preserve the intended isolation path through the magnetics. In industrial products, validate conducted and radiated emissions with the final enclosure, cable, and power-converter layout because PCB-level compliance alone does not establish enclosure-level EMC performance.
合規資訊
The manufacturer identifies IEEE 802.3-2005-compliant register support. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established from the available product material.