LAN9255-I/ZMX020 - 2/3-Port EtherCAT Controller | Microchip
MPN: LAN9255-I/ZMX020 ✓ 啟用中LAN9255-I/ZMX020 概覽
An EtherCAT device controller is an integrated semiconductor used in industrial Ethernet automation systems to manage EtherCAT communication and connected I/O devices. Its internal architecture combines an EtherCAT processing subsystem, Ethernet physical-layer transceivers, and a microcontroller. This integration reduces the number of discrete interface components required around the controller and provides a platform for motion-control, robotics, machine-interconnect, and distributed automation equipment.
The LAN9255-I/ZMX020 provides two integrated full-duplex 100BASE-TX PHYs, an Arm Cortex-M4F-based application subsystem, 20 MHz MCU operation, and 1.024 MB of SRAM. Its EtherCAT interface, dual-PHY arrangement, RMII interface, and USB 2.0 interface support use in embedded EtherCAT slave equipment. The 128-pin TQFP package provides the pin count required for the parallel processor, memory, Ethernet, clock, and power connections of the integrated system-in-package.
The Microchip datasheet 00003646B identifies the LAN9255 as a system-in-package combining the LAN9253 2/3-port EtherCAT device controller, two integrated Ethernet PHYs, and the SAM E53J Arm Cortex-M4F MCU. Each PHY supports full-duplex 100BASE-TX operation at 100 Mbps. The integrated microcontroller provides application-specific processing alongside real-time EtherCAT communication handling.
Typical uses include EtherCAT slave modules, distributed I/O controllers, servo and stepper-motion interfaces, industrial sensor gateways, machine vision equipment, and compact robotic control nodes. The two-PHY arrangement is particularly useful where a device must bridge or connect multiple 100BASE-TX Ethernet segments while executing local control functions.
PCB design must account for 128 pins, Ethernet magnetics or coupling requirements, supply decoupling, clock integrity, and high-speed differential routing. Magnetic isolation or suitable PHY coupling components should be selected according to the manufacturer reference design, while differential pairs should remain continuously referenced to a solid ground plane. Review the full pin-description table in the manufacturer datasheet before assigning PCB nets.
This page organizes the controller’s verified architecture, package details, purchasing information, drop-in options, and application guidance. The comparison section distinguishes temperature-grade and ordering-code variants, while the engineering notes focus on Ethernet signal integrity, power implementation, and firmware integration for EtherCAT equipment.
直接替換替代品,適用於 LAN9255-I/ZMX020 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LAN9255-I/ZMX020 (相同外形與佔位) — 差異在於 Ethernet Speed, Integrated MCU, Package.
LAN9255/ZMX020
✅ 直接替換📋 參考替代品(不在目錄中)
LAN9255-V/ZMX020
✅ 直接替換聯絡詢價
查看資料表 →LAN9255-I/ZMX020 規格
| Device Type | 2/3-port EtherCAT device controller with integrated MCU |
| Integrated MCU | SAM E53J 32-bit Arm Cortex-M4F |
| MCU Clock | 20 MHz |
| Integrated SRAM | 1.024 MB |
| Ethernet Standard | IEEE 802.3 |
| Ethernet Speed | 100 Mbps |
| Physical Layer | Dual 100BASE-TX PHYs |
| PHY Duplex Mode | Full duplex |
| EtherCAT Port Configuration | 2/3 ports |
| 介面 | RMII and USB 2.0 |
| 封裝 | 128-pin TQFP, 14 x 14 mm |
| 安裝類型 | Surface mount |
| Architecture | System-in-package |
| Ethernet PHY Count | 2 integrated PHYs |
| Supported Ethernet Rate | 100BASE-TX at 100 Mbps |
| Processor Architecture | 32-bit Arm Cortex-M4F |
LAN9255-I/ZMX020 128-pin tqfp, 14 x 14 mm 腳位配置指南
LAN9255-I/ZMX020(128-pin tqfp, 14 x 14 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: LAN9255-I/ZMX020.
請參閱 資料表 以查看完整腳位配置。
典型應用
LAN9255-I/ZMX020 適用於 6 應用s: Industrial EtherCAT I/O Modules, Servo and Stepper-Motion Interfaces, Robotic Control Nodes, Machine-Vision Ethernet Gateways, Distributed Sensor Hubs, Compact EtherCAT Test Equipment.
Industrial EtherCAT I/O Modules
The LAN9255-I/ZMX020 fits compact EtherCAT slave modules because it combines a 2/3-port EtherCAT controller with two full-duplex 100BASE-TX PHYs and an application MCU in one package. The Cortex-M4F subsystem can execute local acquisition, diagnostics, and control functions while the EtherCAT section manages cyclic fieldbus traffic. Its 1.024 MB of integrated SRAM reduces external memory requirements compared with a discrete processor-and-PHY architecture. In an I/O module, the controller can connect local inputs and outputs, forward line signals through the second PHY, and provide a single Ethernet interface to the EtherCAT master. Designers should follow the manufacturer reference schematic for magnetics, isolation, termination, and decoupling rather than treating the integrated PHYs as zero-component Ethernet interfaces.
推薦
Servo and Stepper-Motion Interfaces
The LAN9255-I/ZMX020 is appropriate for distributed servo and stepper-motion interfaces that need EtherCAT communication and local control processing in a compact controller. Its 20 MHz Arm Cortex-M4F MCU provides the application-processing foundation, while the dedicated EtherCAT controller handles fieldbus operation independently from the user application. The dual 100BASE-TX PHYs support line-side network connectivity and additional Ethernet-oriented functions where required. This combination can reduce controller-board area compared with separate MCU, Ethernet interface, and PHY implementations. For a motor-control board, keep high-current switching circuitry physically separated from the Ethernet and MCU sections, and validate synchronization behavior with the EtherCAT master and the firmware timing specified by Microchip.
推薦
Robotic Control Nodes
The LAN9255-I/ZMX020 can serve as the communications and control core of an EtherCAT-enabled robotic node because it integrates network physical layers, an EtherCAT device controller, and a microcontroller capable of handling local motion or sensor logic. The 2/3-port architecture and 100 Mbps dual-PHY implementation allow a node to participate in a line network while supporting additional local Ethernet connectivity. Its integrated SRAM is useful for EtherCAT process-image buffering and control variables, while the MCU handles application-level coordination. In a robot controller, isolate the controller from motor-drive transients, keep Ethernet differential routing away from switching nodes, and use the manufacturer’s hardware reference design to select magnetics and supply networks. Firmware selection and EtherCAT conformance remain separate from package-level substitution checks.
推薦
Machine-Vision Ethernet Gateways
The LAN9255-I/ZMX020 is suitable for machine-vision gateways that must coordinate EtherCAT-connected equipment while exchanging data over an Ethernet network. The two integrated full-duplex 100BASE-TX PHYs provide dedicated copper-network interfaces, and the Cortex-M4F subsystem can handle protocol conversion, device status, and local control. At 100 Mbps, the Ethernet side is appropriate for industrial control traffic rather than high-bandwidth video transport, so image data should remain on a dedicated interface when required. Using the controller as a protocol or motion gateway can simplify board partitioning because Ethernet physical-layer circuitry is integrated with the application processor. The design should use controlled-impedance routing, suitable surge protection, and chassis-ground arrangements appropriate to the installation environment.
推薦
Distributed Sensor Hubs
The LAN9255-I/ZMX020 can support distributed sensor hubs that aggregate local sensing and actuator information for an EtherCAT master. Its Cortex-M4F processor is suitable for sampling, filtering, diagnostics, and data preparation, while the integrated PHYs remove the need for separate 100BASE-TX transceiver devices on each port. The available SRAM allows protocol objects and control buffers to be maintained without a separate external memory component. A sensor hub can place acquisition circuitry near the connectors and isolate its sensitive analog paths from Ethernet and processor sections. Use the datasheet reference layout for clock distribution and decoupling, observe the manufacturer’s Ethernet magnetics guidance, and test conducted and radiated emissions under the intended enclosure and cable configuration.
推薦
Compact EtherCAT Test Equipment
The LAN9255-I/ZMX020 is well suited to compact EtherCAT test equipment because it combines device-controller functionality, two Ethernet PHYs, and an application MCU in one 128-pin package. The MCU can execute test sequences, collect diagnostic information, and present results through a local interface, while the EtherCAT section participates in a network under test. This integration allows a compact instrument to act as a slave device, network monitor, or service node without requiring separate Ethernet-interface components. The 100BASE-TX limit should be considered when defining expected throughput. For a bench instrument, use isolated communication boundaries where required, keep test connectors away from high-speed digital return currents, and validate timing behavior with the actual master and cable lengths used in production.
推薦
推薦產品摘要
工程參考資料,適用於 LAN9255-I/ZMX020 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LAN9255/ZMX020 | LAN9255-V/ZMX020 |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 128-TQFP (14x14) | 128-TQFP (14x14) | 128-TQFP (14x14) |
| EtherCAT Configuration | 2/3 ports | 2/3 ports | 2/3 ports |
| Integrated MCU | Arm Cortex-M4F | Arm Cortex-M4F | Arm Cortex-M4F |
| MCU Clock | 20 MHz | 20 MHz | 20 MHz |
| Integrated SRAM | 1.024 MB | 1.024 MB | 1.024 MB |
| Ethernet PHY Count | 2 integrated 100BASE-TX PHYs | 2 integrated 100BASE-TX PHYs | 2 integrated 100BASE-TX PHYs |
| Ethernet Speed | 100 Mbps | 100 Mbps | 100 Mbps |
| Interfaces | RMII and USB 2.0 | RMII and USB 2.0 | RMII and USB 2.0 |
主要差異化特點
- EtherCAT processing, Ethernet PHYs, and application MCU in one package (對比LAN9255/ZMX020)
- No PCB footprint change for V-grade sourcing (對比LAN9255-V/ZMX020)
- Integrated local application processing (對比LAN9255-V/ZMX020)
設計說明
Implement each 100BASE-TX channel as a continuous controlled-impedance differential pair with a solid reference plane and minimal stubs. Keep PHY-support components and the connections to Ethernet magnetics or coupling components as short as practical. Route the two channels away from switching power stages and high-current motor-drive nodes, and apply the manufacturer reference-layout guidance in datasheet 00003646B.
Separate the controller’s core, Ethernet-PHY, and digital I/O supply networks as specified by the manufacturer, placing the required bypass capacitors at the associated pins. Validate startup sequencing, supply tolerances, and the maximum operating current before finalizing component selection. Estimated power dissipation cannot be stated without the selected supply voltage and operating-current profile, so use the electrical-characteristics table for the final thermal calculation.
Place decoupling, clock components, and Ethernet interface components close to their associated LAN9255-I/ZMX020 pins. Preserve the package’s thermal-land geometry specified in datasheet 00003646B and avoid placing high-temperature or switching components beneath the controller unless the thermal design explicitly accounts for them. Because the exact library diagram is unavailable for this 128-pin TQFP, use the manufacturer package drawing for land-pattern and pin-one placement.
Do not treat the LAN9255-I/ZMX020, LAN9255/ZMX020, and LAN9255-V/ZMX020 as interchangeable without checking the grade-related requirements. The shared package and functional architecture make them footprint-compatible candidates, but temperature range, qualification, and ordering details must be confirmed from manufacturer documentation. Also avoid assuming that integrated PHYs eliminate the need for Ethernet magnetics, surge protection, or correctly selected coupling components.
合規資訊
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were found in the available product information. Confirm compliance for the exact ordering code with the manufacturer before procurement.