LM211DR2G - Single 5-30V Comparator | onsemi
MPN: LM211DR2G ✓ 啟用中LM211DR2G 概覽
A voltage comparator is an analog signal-conditioning component that compares two input voltages and produces a logic-level output indicating which input is higher. Comparators belong to the broader amplifier and comparator hierarchy, where they sit between sensor or measurement inputs and digital control logic. Unlike an operational amplifier intended primarily for linear amplification, the LM211 is optimized for rapid, direct threshold decisions, making it useful in industrial control, sensing, protection, and switching interfaces.
Key features include a single-comparator configuration, a 5 V to 30 V supply range, a 200 ns response time, and an operating temperature range of -25 °C to +85 °C. Its open-collector output provides flexible pull-up placement and permits the output to drive lamps, relays, and other loads referenced to ground, VCC, or VEE. These characteristics make the device useful where a logic decision must be translated into an actionable system output.
The LM211 architecture supports input voltages that are isolated from system ground when split supplies are used. This allows the comparator inputs to monitor signals in systems that also use negative rails. The output topology is flexible rather than tied to only one fixed supply, which helps engineers construct level-shifting, isolation, and relay-driving circuits without changing the comparator package or footprint.
Typical applications include industrial sensor thresholding, overvoltage and undervoltage detection, relay activation, lamp control, window or level comparators, and interfaces between analog measurement circuitry and TTL or MOS logic. The 200 ns response time is also suitable for moderate-speed control loops where delayed comparison would reduce system responsiveness. Designers should account for input common-mode range, output pull-up requirements, supply decoupling, and permissible output current when laying out the circuit.
Place the device close to the driven logic and route the open-collector output away from sensitive analog inputs to reduce switching transients. Use a suitable pull-up resistor for TTL or MOS interfacing, and verify that the selected load does not exceed the output sink-current limits. This page combines the principal operating characteristics, practical implementation guidance, compatible alternatives, and application context for faster component selection.
直接替換替代品,適用於 LM211DR2G — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM211DR2G (相同外形與佔位) — 差異在於 Logic Compatibility, Comparator Type, Output Type, Package, Input Configuration.
LM211D
✅ 直接替換聯絡詢價
查看資料表 →LM211DR2
✅ 直接替換📋 參考替代品(不在目錄中)
LM211QDRG4
✅ 直接替換📋 參考替代品(不在目錄中)
LM211DR
✅ 直接替換聯絡詢價
查看資料表 →LM211PW
✅ 直接替換聯絡詢價
查看資料表 →LM211DR2G 最大額定值與電氣特性
| Comparator Type | Single general-purpose voltage comparator |
| Supply Voltage Range, Single Supply | 5 V to 30 V |
| Supply Voltage Range, Split Supply | ±15 V |
| Response Time | 200 ns |
| 工作溫度範圍 | -25 °C to +85 °C |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| 輸出類型 | Open collector |
| Logic Compatibility | DTL, MOS, open-emitter, open-collector, RTL, and TTL |
| Number of Comparators | 1 |
| Input Isolation | Inputs may be isolated from system ground with split supplies |
| Output Reference Flexibility | Loads may be referenced to ground, VCC, or VEE |
| Output Drive Capability | Capable of driving lamps and relays |
LM211DR2G 8-pin soic 腳位配置指南
LM211DR2G(8-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM211DR2G.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM211DR2G 適用於 6 應用s: Industrial Sensor Threshold Detection, Overvoltage and Undervoltage Protection, Relay and Lamp Drive Interface, TTL and MOS Logic Interfacing, Automatic Control Level Switch, Test and Measurement Threshold Fixture.
Industrial Sensor Threshold Detection
The LM211DR2G fits industrial sensor thresholding because its 5 V to 30 V supply range supports common control rails and its 200 ns response time converts an analog crossing into a prompt logic decision. Place the sensor signal on one input and a reference voltage on the other, then use the open-collector output to signal an upper-level controller. The comparator can also drive a relay or indicator when the load current remains within the output rating. For noisy factory environments, filter the sensor node carefully and provide local supply bypassing so switching transients do not alter the threshold decision.
推薦
Overvoltage and Undervoltage Protection
A voltage supervisor built around the LM211DR2G can monitor a power rail and change state when a reference or divided feedback signal crosses the safe operating limit. The 200 ns response time allows the output state to change rapidly during a fault, while the open-collector architecture permits a pull-up to the voltage used by the protection logic. A relay, shutdown signal, or indicator can be connected when its current is within the device limit. Designers should include hysteresis to prevent repeated switching near the threshold and verify the divider tolerances across temperature.
推薦
Relay and Lamp Drive Interface
The LM211DR2G is suited to relay and lamp interfaces because its open-collector output can sink current from a pull-up load. Connect the relay coil between the pulled-up output and the appropriate supply reference, and add a flyback diode across the coil to suppress inductive switching transients. The comparator’s 200 ns response time provides rapid state changes, but the load current must remain within the output limits. For larger coils or inductive loads with high stored energy, use a driver transistor and retain the LM211DR2G as the low-current decision stage.
推薦
TTL and MOS Logic Interfacing
The LM211DR2G provides a flexible interface between analog measurement circuits and digital logic through its open-collector output. A pull-up resistor can reference the output to the supply required by a TTL or MOS receiver, allowing the comparator to operate from a different rail than the logic it controls. This arrangement is useful in legacy industrial systems and mixed-voltage test equipment. Select the pull-up resistance using the receiving gate’s input-current and rise-time requirements, and keep the output routing away from high-impedance sensor nodes to minimize switching coupling.
推薦
Automatic Control Level Switch
The LM211DR2G can implement a simple automatic level controller for tanks, dispensers, or mechanical systems by comparing a sensed level against a reference voltage. Its 200 ns response time allows the controller to act quickly when the input crosses the threshold, while the wide 5 V to 30 V supply range supports industrial control voltages. The open-collector output may drive a relay, pilot lamp, or logic input. Add positive feedback to create hysteresis, and make sure sensor grounding and the comparator’s common-mode limits preserve reliable operation near the end points of the measurement range.
推薦
Test and Measurement Threshold Fixture
The LM211DR2G is useful in test fixtures that must convert an analog waveform or DC level into a binary pass, fail, or trigger event. Its 200 ns response time supports higher measurement bandwidth than slower general-purpose comparators, and the open-collector output can feed TTL instrumentation when pulled up to the appropriate logic supply. Use a controlled reference source for repeatable threshold decisions and account for input offset when the measurement resolution is critical. Short output traces and local decoupling help maintain measurement integrity when the comparator sits near sensitive test equipment.
推薦
推薦產品摘要
工程參考資料,適用於 LM211DR2G — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM211D | LM211DR2 | LM211QDRG4 | LM211DR | LM211 |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | onsemi | onsemi | onsemi | onsemi | UMW | Texas Instruments |
| Comparator Type | Single general-purpose comparator | Single comparator | Single comparator | Differential comparator with strobe | Single comparator | Single high-speed comparator |
| Single Supply Range | 5 V to 30 V | 5 V to 30 V | 5 V to 30 V | 5 V to 30 V | 5 V to 30 V | 5 V to 30 V |
| Split Supply Capability | ±15 V | ±15 V | ±15 V | ±15 V | ±15 V | ±15 V |
| Output Configuration | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Logic Compatibility | DTL, MOS, open-emitter, open-collector, RTL, and TTL | DTL, MOS, open-emitter, open-collector, RTL, and TTL | DTL, MOS, open-emitter, open-collector, RTL, and TTL | DTL, MOS, open-emitter, open-collector, RTL, and TTL | DTL, MOS, open-emitter, open-collector, RTL, and TTL | Compatible with most TTL and MOS circuits |
主要差異化特點
- Wide single-supply operating range (對比LM211)
- Fast threshold response (對比LM211D)
- Commercial-temperature focus with a broader-qualified alternative available (對比LM211QDRG4)
- Open-collector output flexibility (對比LM2904PWR)
設計說明
Place the LM211DR2G close to the signals being compared and provide local supply bypassing with a short ground return. Keep the open-collector output away from sensitive high-impedance inputs because its transition can create coupling through board capacitance. When the comparator controls a relay or lamp, route the higher-energy load current separately from the comparator and logic traces, and place any flyback diode directly across the inductive coil.
Do not treat the open-collector output as a actively driven push-pull logic output. A pull-up resistor is required to establish the inactive high state. Select that resistor to balance receiver input current against output rise time, and connect it to the supply used by the receiving logic. Also observe the comparator’s common-mode input limits; the 5 V to 30 V supply range does not imply that every input voltage within the rail-to-rail span is valid.
Add intentional hysteresis when noise near the threshold could cause output chatter. This can be implemented with positive feedback from the output to the reference side of one input, subject to the device’s input-range and output-swing restrictions. Keep the reference network low impedance and separate from the pull-up node so switching transients do not shift the decision level.
The open-collector stage dissipates power primarily while sinking the pull-up and load current. Check the output sink-current limit and calculate worst-case dissipation using the maximum pull-up voltage and load current. The pull-up resistance should be large enough to remain within that limit but small enough to meet the receiving logic’s rise-time requirement. Bypass the supply pins at the package to keep switching events from modulating the comparator’s reference behavior.
合規資訊
The LM211DR2G is listed as active, but device-specific environmental and material-compliance declarations are not stated in the accessible product information. LM211QDRG4 is identified as an automotive-grade option, but that does not establish AEC-Q100 status for LM211DR2G.