LM211DRG4 - High-Speed Differential Comparator | Texas Instruments
MPN: LM211DRG4 ✓ 啟用中LM211DRG4 概覽
A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference between them crosses a defined threshold. It belongs to the comparator hierarchy, which includes general-purpose comparators, differential comparators, and interface ICs. Compared with a general-purpose op-amp, a comparator provides faster threshold-oriented switching and an output stage designed to connect more directly to digital logic, lamps, or relays.
The LM211 family combines single-comparator architecture with broad supply-voltage support. A 5 V implementation simplifies compatibility with TTL and MOS logic, while split or dual supplies support ±15 V industrial and analog systems. The strobe input provides a way to inhibit output transitions during selected operating intervals, and the open-collector output permits external pull-up selection and wired-interface functions. The LM211DRG4 is specified for operation from -40°C to 85°C and uses the TI D package, an 8-pin surface-mount SOIC.
The open-collector output is important because it allows the output voltage, rise time, and sink current to be adapted with an external pull-up resistor. It can directly support compatible logic families when the pull-up voltage and resistor are selected correctly. However, an open-collector output cannot source current independently, so the external pull-up is required in normal operation. Designers should also account for the propagation interval around the strobe control when timing system-level events.
Typical uses include zero-crossing detection, overvoltage and undervoltage monitoring, industrial control interfaces, relay or lamp drivers, and signal conditioning where a logic-level indication is required. The comparator can operate from 5 V in a logic-control board or from higher positive and negative rails when the monitored signals exceed single-supply limits. Its wide supply range allows one device family to serve multiple industrial and instrumentation architectures.
For robust layouts, keep the input traces short, place the output pull-up close to the comparator, and provide adequate ground-return paths. Do not allow floating input nodes during power transitions; use input bias resistors when necessary. Review the manufacturer datasheet for input common-mode limits, output sink-current limits, supply-current behavior, and absolute maximum ratings before operating the LM211DRG4 near its supply limits.
This page combines the exact LM211DRG4 ordering information with package, pinout, application, replacement, and design guidance. It also identifies same-footprint alternatives for design review while keeping separate the device's verified electrical limits and the practical conditions that determine whether it is suitable for a particular system.
直接替換替代品,適用於 LM211DRG4 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM211DRG4 (相同外形與佔位) — 差異在於 Comparator Type, Logic Compatibility, Output Drive Capability, Package, Input Configuration.
LM211DR
✅ 直接替換聯絡詢價
查看資料表 →LM211DG
✅ 直接替換聯絡詢價
查看資料表 →LM211DG4
✅ 直接替換📋 參考替代品(不在目錄中)
LM211QDRG4
✅ 直接替換📋 參考替代品(不在目錄中)
LM211QDREP
✅ 直接替換📋 參考替代品(不在目錄中)
LM211DRG4 最大額定值與電氣特性
| Comparator Type | Single high-speed differential comparator with strobe |
| Number of Channels | 1 channel |
| Single-Supply Operation | 5 V |
| Positive and Negative Supply Support | Up to ±15 V |
| 供應電流 | 5.1 mA |
| Logic Compatibility | TTL and MOS output-level compatible |
| Output Architecture | Open-collector |
| Output Drive Capability | Capable of driving lamps or relays |
| Input Configuration | Differential inputs: inverting and non-inverting |
| Strobe Control | Yes |
| 工作溫度範圍 | -40°C to 85°C |
| 封裝 | 8-pin SOIC (D package) |
| Package Type | SOIC-8 surface-mount package |
| 腳位數 | 8 pins |
LM211DRG4 腳位配置
| 腳位 1 | OUT — Open-collector comparator output |
| 腳位 2 | -IN — Inverting input |
| 腳位 3 | +IN — Non-inverting input |
| 腳位 4 | GND — Ground connection |
| 腳位 5 | GND — Ground connection |
| 腳位 6 | STROBE — Output strobe control input |
| 腳位 7 | V+ — Positive supply connection |
| 腳位 8 | NC — Not connected (per datasheet) |
典型應用
LM211DRG4 適用於 6 應用s: Industrial Overvoltage Detection, TTL Logic Interface, Relay Driver Circuit, Zero-Crossing Detector, Power Supply Fault Monitor, Lamp Drive and Status Control.
Industrial Overvoltage Detection
The LM211DRG4 fits threshold-based overvoltage detection because it compares a monitored voltage against a reference and changes state when the differential input crosses the decision point. Its 5 V single-supply operation is convenient for logic-controlled industrial equipment, while its open-collector output can operate a relay, alarm, or status input through an external pull-up network. The 8-pin SOIC package supports compact PCB placement, and the -40°C to 85°C rating covers a broad range of industrial enclosure environments. Designers should verify the input common-mode range and output sink-current limits against the monitored circuit before implementation.
推薦
TTL Logic Interface
The LM211DRG4 is appropriate for a TTL interface because TI specifies that the LM211 output levels are compatible with most TTL and MOS circuits. A 5 V supply allows the device to sit directly in a 5 V logic system, while the open-collector output provides a flexible pull-up arrangement. Use a resistor network to establish the required high level and control the transition rate into the receiving gate. The single-channel architecture makes it useful for one isolated threshold or handshake signal rather than a full differential receiver.
推薦
Relay Driver Circuit
The LM211DRG4 can serve as the decision element in a relay-driver circuit because TI identifies the LM211 family as capable of driving lamps or relays. The comparator converts a voltage comparison into an open-collector switching event, which can control a pull-up and relay-driver transistor stage. This separation allows the comparator to operate from a low-voltage logic rail while the relay coil uses a separate supply. Confirm coil current, flyback protection, output sink rating, and isolation requirements during schematic design.
推薦
Zero-Crossing Detector
The LM211DRG4 is suitable for a zero-crossing detector when a rapid output transition is needed around a reference crossing. Its high-speed differential-comparator architecture compares the input signal with a threshold, and the open-collector output can pull down a logic node through an external pull-up. The single 5 V supply simplifies digital-system integration, while the -40°C to 85°C operating range supports industrial and instrumentation environments. Keep feedback and input routing short to prevent oscillation or false transitions near the crossing point.
推薦
Power Supply Fault Monitor
The LM211DRG4 can monitor a power rail by comparing a scaled rail voltage with a reference and generating a fault indication when the difference crosses the selected threshold. The open-collector output provides a convenient way to combine an alarm signal with other open-collector nodes, subject to the pull-up design and sink-current limit. Its wide supply support allows operation in both 5 V control systems and higher positive or negative analog rails. Input attenuation, fault-response polarity, and startup behavior must be evaluated for the target power architecture.
推薦
Lamp Drive and Status Control
The LM211DRG4 can drive a lamp or produce a status indication because the LM211 family is explicitly described as capable of driving lamps and relays. Its open-collector output works with an appropriate pull-up and, when necessary, an external driver stage. This makes it useful for threshold-activated annunciators, panel indicators, and process-equipment status lamps. The 8-pin SOIC package simplifies board assembly, but the selected lamp or transistor must remain within the comparator's output and thermal limits.
推薦
推薦產品摘要
工程參考資料,適用於 LM211DRG4 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM211DR | LM211DG | LM211DG4 | LM211QDRG4 | LM211QDREP |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-8 | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same | SOIC-8 - same |
| Comparator Type | Single differential comparator with strobe | Single differential comparator | Single differential comparator | Single differential comparator | Single differential comparator | Single differential comparator |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Number of Pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins |
| Mounting Style | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
| Qualification Class | Standard grade | Standard grade | Standard grade | Standard grade | Q-prefixed qualification option | Q-prefixed qualification option |
主要差異化特點
- Exact family-level drop-in option without changing the SOIC-8 footprint (對比LM211DR)
- Direct PCB reuse with the LM211 DG ordering configuration (對比LM211DG)
- Qualified LM211-family option available for stricter design requirements (對比LM211QDRG4)
- Seven-pin-equivalent functional scale is unnecessary because the full LM211 footprint remains available (對比LM211QDREP)
設計說明
Do not treat the open-collector output as a push-pull logic output. Install an external pull-up resistor to establish the inactive high level, and select its value so the output remains within the sink-current limit while meeting the receiving logic's rise-time requirement. Check the maximum output voltage, output current, and operating-temperature limits in the manufacturer datasheet before connecting a relay, lamp, or TTL load.
Keep the two input nets short and route them away from the output and pull-up node to reduce feedback from output transients. Provide a low-impedance ground return for both GND pins and place the output pull-up close to the comparator. If either input can become unpowered or floating during startup, add suitable bias resistors or redesign the interface so the differential input remains in a defined state.
Use separate supply-decoupling paths for the comparator and any relay or lamp load so switching transients do not disturb the logic rail. Decouple the LM211 supply close to pins 7 and the ground pins with a high-frequency capacitor and a suitable bulk reservoir. Because the device supports 5 V and positive or negative rails up to ±15 V, verify the actual supply configuration and common-mode limits for both input signals.
Account for the strobe input when defining valid output states. A system that treats OUT as always reflecting the instantaneous input comparison can behave incorrectly during strobe intervals. Review the truth table and timing characteristics in the manufacturer datasheet, and design external logic so downstream circuitry interprets the inhibited state correctly. This is especially important in pulsed sensing, latching, and sampled-measurement systems.
合規資訊
The cross-reference material discusses RoHS and REACH attributes but does not provide final compliance values for LM211DRG4. The standard LM211DRG4 orderable part is not identified as an automotive-qualified option; use the LM211QDRG4 documentation for an automotive-qualified family configuration.