LM2893MX - 20-Pin Carrier-Current Transceiver | Texas Instruments
MPN: LM2893MX ✓ 啟用中LM2893MX 概覽
A carrier-current transceiver is an interface circuit that couples serial data onto and receives data from an electrical distribution or communication line. Carrier-current systems use an existing power or telephone conductor as the physical transmission medium, allowing equipment located at separate points to exchange information without a dedicated data cable. This places the LM2893MX within the broader hierarchy of communication interface IC, transceiver, line-interface circuit, and semiconductor.
The LM2893MX is identified as a telecom interface transceiver and a general-purpose carrier-current interface. Its half-duplex operation supports two-way communication over the same line path, while the 79 mA maximum supply current provides a defined operating limit for power-supply design. The SOIC-20 package supports conventional surface-mount assembly and is suitable for equipment operating across the full -40°C to +85°C industrial temperature range.
Carrier-current interfaces depend on accurate line coupling, controlled transmitter behavior, and receiver discrimination between wanted signals and line noise. The LM2893MX integrates the functional interface required for bidirectional serial bit-stream communication at the physical layer. System designers still need to account for line impedance, coupling components, termination, filtering, grounding, and protection networks when constructing a production interface.
Typical applications include power-line data links, industrial equipment monitoring, remote telemetry, building automation, carrier-based communication equipment, and telecommunication networks that use existing conductors as communication media. The operating voltage and industrial temperature range make the device relevant to sustained industrial deployments where the interface must tolerate temperature variation and operate from a nominal 18 V supply.
Design the LM2893MX around the electrical characteristics of the carrier line rather than treating it as a conventional point-to-point logic interface. External components must be selected for the line voltage, impedance, baud rate, isolation requirements, and transient environment, while the PCB layout should minimize noise coupling between the transmit and receive paths. Confirm the exact pin functions and recommended application circuit in the Texas Instruments datasheet before finalizing a new layout.
This product page combines the LM2893MX electrical, package, environmental, and application information with practical PCB and implementation guidance. It also distinguishes the verified device characteristics from parameters that must be confirmed during design-in, helping engineers evaluate the part efficiently while retaining control over circuit-level requirements.
直接替換替代品,適用於 LM2893MX — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2893MX (相同外形與佔位) — 差異在於 Communication Mode, Number of Terminals, Package, RoHS Status.
LM2893MX 規格
| Product Type | Carrier-current transceiver (1 device) |
| Interface Category | Telecom interface IC (1 device) |
| Communication Mode | Half-duplex, bidirectional serial communication (1 interface) |
| Nominal Supply Voltage | 18 V |
| First Supply Voltage Range | 13 V to 24 V |
| Second Supply Voltage Range | 14 V to 30 V |
| Maximum Supply Current | 79 mA |
| Minimum Operating Temperature | -40°C |
| Maximum Operating Temperature | +85°C |
| 封裝 | 20-pin SOIC, 300 mil |
| Number of Terminals | 20 pins |
| Terminal Pitch | 1.27 mm |
| Terminal Form | Gull wing |
| Mounting Technology | Surface mount |
| RoHS 狀態 | RoHS compliant |
| Manufacturer | Texas Instruments |
LM2893MX 20-pin soic, 300 mil 腳位配置指南
LM2893MX(20-pin soic, 300 mil 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: LM2893MX.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2893MX 適用於 6 應用s: Power-Line Data Communication, Industrial Equipment Telemetry, Remote Metering and Telemetry, Building Automation Networks, Carrier-Based Networking Equipment, Half-Duplex Bidirectional Data Links.
Power-Line Data Communication
The LM2893MX fits carrier-current data links that use an existing power conductor as a bidirectional communication medium. Its half-duplex architecture allows serial information to travel over the same line path in both directions, avoiding a separate data cable between endpoints. The nominal 18 V supply and 79 mA maximum current suit an industrial telecom interface, while the -40°C to +85°C range supports temperature variation. External coupling capacitors, line filtering, transient protection, and grounding remain essential because the carrier line can carry high-voltage noise and switching disturbances.
Industrial Equipment Telemetry
The LM2893MX can provide the physical interface for remote industrial equipment that exchanges status and control data over a carrier-current network. The 20-pin SOIC package supports conventional surface-mount PCB assembly, and its 1.27 mm lead pitch allows a compact interface footprint. With a nominal 18 V operating point and operation from -40°C to +85°C, the device is relevant to machinery monitoring and supervisory installations. The line interface should be isolated or protected according to the installation environment, and supply filtering must accommodate the specified 79 mA maximum current.
Remote Metering and Telemetry
The LM2893MX is applicable to metering equipment that periodically exchanges serial information over an existing electrical distribution line. Half-duplex, bidirectional communication allows a remote endpoint to report measurements and receive commands without dedicated signal pairs. Its 20-terminal SOIC package and industrial temperature grade support robust embedded designs, but the circuit must be tuned to the line impedance and communication speed. Carefully isolate the transceiver from conducted surge events and place filtering close to the line-coupling components to prevent energy from reaching the transmitter.
Building Automation Networks
The LM2893MX can support low- and medium-speed building automation links that reuse building wiring for control and monitoring traffic. Bidirectional half-duplex operation is useful when controllers share wiring among multiple endpoints and must regulate access to the carrier-current medium. The component's -40°C to +85°C range supports equipment installed in variable-temperature environments, and its 18 V nominal supply aligns with many industrial control rails. Designers should verify protocol timing, line loading, insulation requirements, and fault-current protection before integrating it into a building power network.
Carrier-Based Networking Equipment
The LM2893MX suits telecommunication and networking equipment requiring a robust serial interface over a carrier-current line rather than a conventional isolated data transformer. Its 79 mA maximum supply current provides a defined limit for power planning, and the 20-pin SOIC-300 mil package allows integration with surrounding analog and digital circuitry. To achieve dependable communication, use controlled line coupling, receive filtering, common-mode protection, and a layout that separates sensitive receiver paths from the transmitter and switching supply nodes.
Half-Duplex Bidirectional Data Links
The LM2893MX is specifically suited to half-duplex, bidirectional serial bit-stream links where both endpoints share one carrier path. This arrangement can reduce wiring requirements in distributed control systems while retaining a clear communication role for each endpoint. The industrial temperature range and surface-mount SOIC package suit production control electronics, but contention, turnaround timing, and line-level settling must be managed by the surrounding system. The carrier medium should be characterized for noise, impedance, and fault energy before the interface is released to production.
工程參考資料,適用於 LM2893MX — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Product Type | Carrier-current transceiver |
| Brand | Texas Instruments |
| Package | 20-pin SOIC, 300 mil |
| Number of Terminals | 20 pins |
| Terminal Pitch | 1.27 mm |
| Communication Mode | Half-duplex, bidirectional |
| Nominal Supply Voltage | 18 V |
| Maximum Supply Current | 79 mA |
| Operating Temperature | -40°C to +85°C |
| RoHS Status | Compliant |
主要差異化特點
- Dedicated carrier-current interface function (對比A standard RS-232 transceiver)
- Industrial temperature coverage (對比A commercial-temperature SOIC-20 transceiver)
- Compact 20-pin surface-mount footprint (對比A carrier-current interface in a larger through-hole package)
設計說明
Place the LM2893MX close to the line-coupling and protection components, and keep the carrier-current path physically separated from sensitive receiver nodes. Route the transmit and receive sections according to the Texas Instruments application circuit rather than treating them as ordinary digital signals. Use a continuous ground reference under the device where the board construction permits, and minimize loop area between the transceiver, coupling network, and protection components.
Design the nominal 18 V supply path for the confirmed 79 mA maximum operating current, allowing margin for temperature, component tolerance, and nearby circuit load. Place local decoupling close to the supply pins and keep high-current and switching-node paths away from the carrier interface. Confirm the correct 13 V to 24 V or 14 V to 30 V operating range for the selected circuit configuration in the manufacturer datasheet before defining the regulator output.
Characterize the carrier line for impedance, noise, and fault conditions before selecting the external coupling and receive-filter values. The LM2893MX supports half-duplex bidirectional serial communication, so receiver discrimination and turnaround behavior are central to link reliability. Use the manufacturer reference interface as the starting point, then validate filtering, attenuation, and data recovery across the required line length, temperature range, and conducted-noise environment.
Do not substitute a standard RS-232 transceiver for the LM2893MX, and do not assume that another 20-pin SOIC device is pin-compatible. Verify signal names, supply limits, carrier-current coupling requirements, and half-duplex behavior against the Texas Instruments pin description. Also avoid allowing surge or mains-coupled energy to reach unprotected transceiver pins; add appropriately rated protection and confirm that its capacitance does not impair receive sensitivity.
合規資訊
RoHS compliance is stated by the LM2893MX product listing. The telecom interface transceiver is not an automotive-qualified AEC-Q100 device, and no separate REACH, lead-free, halogen-free, or conflict-minerals declarations are identified in the verified product information.