LM2893MX - 20-Pin Carrier-Current Transceiver | Texas Instruments
MPN: LM2893MX ✓ فعالLM2893MX جائزہ
A carrier-current transceiver is an interface circuit that couples serial data onto and receives data from an electrical distribution or communication line. Carrier-current systems use an existing power or telephone conductor as the physical transmission medium, allowing equipment located at separate points to exchange information without a dedicated data cable. This places the LM2893MX within the broader hierarchy of communication interface IC, transceiver, line-interface circuit, and semiconductor.
The LM2893MX is identified as a telecom interface transceiver and a general-purpose carrier-current interface. Its half-duplex operation supports two-way communication over the same line path, while the 79 mA maximum supply current provides a defined operating limit for power-supply design. The SOIC-20 package supports conventional surface-mount assembly and is suitable for equipment operating across the full -40°C to +85°C industrial temperature range.
Carrier-current interfaces depend on accurate line coupling, controlled transmitter behavior, and receiver discrimination between wanted signals and line noise. The LM2893MX integrates the functional interface required for bidirectional serial bit-stream communication at the physical layer. System designers still need to account for line impedance, coupling components, termination, filtering, grounding, and protection networks when constructing a production interface.
Typical applications include power-line data links, industrial equipment monitoring, remote telemetry, building automation, carrier-based communication equipment, and telecommunication networks that use existing conductors as communication media. The operating voltage and industrial temperature range make the device relevant to sustained industrial deployments where the interface must tolerate temperature variation and operate from a nominal 18 V supply.
Design the LM2893MX around the electrical characteristics of the carrier line rather than treating it as a conventional point-to-point logic interface. External components must be selected for the line voltage, impedance, baud rate, isolation requirements, and transient environment, while the PCB layout should minimize noise coupling between the transmit and receive paths. Confirm the exact pin functions and recommended application circuit in the Texas Instruments datasheet before finalizing a new layout.
This product page combines the LM2893MX electrical, package, environmental, and application information with practical PCB and implementation guidance. It also distinguishes the verified device characteristics from parameters that must be confirmed during design-in, helping engineers evaluate the part efficiently while retaining control over circuit-level requirements.
کے لیے ڈراپ اِن متبادل LM2893MX — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں LM2893MX (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Communication Mode, Number of Terminals, Package, RoHS Status.
LM2893M
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →LM2893MX تفصیلات
| Product Type | Carrier-current transceiver (1 device) |
| Interface Category | Telecom interface IC (1 device) |
| Communication Mode | Half-duplex, bidirectional serial communication (1 interface) |
| Nominal Supply Voltage | 18 V |
| First Supply Voltage Range | 13 V to 24 V |
| Second Supply Voltage Range | 14 V to 30 V |
| Maximum Supply Current | 79 mA |
| Minimum Operating Temperature | -40°C |
| Maximum Operating Temperature | +85°C |
| پیکیج | 20-pin SOIC, 300 mil |
| Number of Terminals | 20 pins |
| Terminal Pitch | 1.27 mm |
| Terminal Form | Gull wing |
| Mounting Technology | Surface mount |
| RoHS اسٹیٹس | RoHS compliant |
| Manufacturer | Texas Instruments |
LM2893MX 20-pin soic, 300 mil پن کنفیگریشن گائیڈ
LM2893MX (20-pin soic, 300 mil پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں LM2893MX.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
LM2893MX کے لیے موزوں ہے 6 ایپلیکیشنs: Power-Line Data Communication, Industrial Equipment Telemetry, Remote Metering and Telemetry, Building Automation Networks, Carrier-Based Networking Equipment, Half-Duplex Bidirectional Data Links.
Power-Line Data Communication
The LM2893MX fits carrier-current data links that use an existing power conductor as a bidirectional communication medium. Its half-duplex architecture allows serial information to travel over the same line path in both directions, avoiding a separate data cable between endpoints. The nominal 18 V supply and 79 mA maximum current suit an industrial telecom interface, while the -40°C to +85°C range supports temperature variation. External coupling capacitors, line filtering, transient protection, and grounding remain essential because the carrier line can carry high-voltage noise and switching disturbances.
Industrial Equipment Telemetry
The LM2893MX can provide the physical interface for remote industrial equipment that exchanges status and control data over a carrier-current network. The 20-pin SOIC package supports conventional surface-mount PCB assembly, and its 1.27 mm lead pitch allows a compact interface footprint. With a nominal 18 V operating point and operation from -40°C to +85°C, the device is relevant to machinery monitoring and supervisory installations. The line interface should be isolated or protected according to the installation environment, and supply filtering must accommodate the specified 79 mA maximum current.
Remote Metering and Telemetry
The LM2893MX is applicable to metering equipment that periodically exchanges serial information over an existing electrical distribution line. Half-duplex, bidirectional communication allows a remote endpoint to report measurements and receive commands without dedicated signal pairs. Its 20-terminal SOIC package and industrial temperature grade support robust embedded designs, but the circuit must be tuned to the line impedance and communication speed. Carefully isolate the transceiver from conducted surge events and place filtering close to the line-coupling components to prevent energy from reaching the transmitter.
Building Automation Networks
The LM2893MX can support low- and medium-speed building automation links that reuse building wiring for control and monitoring traffic. Bidirectional half-duplex operation is useful when controllers share wiring among multiple endpoints and must regulate access to the carrier-current medium. The component's -40°C to +85°C range supports equipment installed in variable-temperature environments, and its 18 V nominal supply aligns with many industrial control rails. Designers should verify protocol timing, line loading, insulation requirements, and fault-current protection before integrating it into a building power network.
Carrier-Based Networking Equipment
The LM2893MX suits telecommunication and networking equipment requiring a robust serial interface over a carrier-current line rather than a conventional isolated data transformer. Its 79 mA maximum supply current provides a defined limit for power planning, and the 20-pin SOIC-300 mil package allows integration with surrounding analog and digital circuitry. To achieve dependable communication, use controlled line coupling, receive filtering, common-mode protection, and a layout that separates sensitive receiver paths from the transmitter and switching supply nodes.
Half-Duplex Bidirectional Data Links
The LM2893MX is specifically suited to half-duplex, bidirectional serial bit-stream links where both endpoints share one carrier path. This arrangement can reduce wiring requirements in distributed control systems while retaining a clear communication role for each endpoint. The industrial temperature range and surface-mount SOIC package suit production control electronics, but contention, turnaround timing, and line-level settling must be managed by the surrounding system. The carrier medium should be characterized for noise, impedance, and fault energy before the interface is released to production.
کے لیے انجینئرنگ ریفرنس ڈیٹا LM2893MX — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ |
|---|---|
| Product Type | Carrier-current transceiver |
| Brand | Texas Instruments |
| Package | 20-pin SOIC, 300 mil |
| Number of Terminals | 20 pins |
| Terminal Pitch | 1.27 mm |
| Communication Mode | Half-duplex, bidirectional |
| Nominal Supply Voltage | 18 V |
| Maximum Supply Current | 79 mA |
| Operating Temperature | -40°C to +85°C |
| RoHS Status | Compliant |
اہم امتیازی خصوصیات
- Dedicated carrier-current interface function (بمقابلہA standard RS-232 transceiver)
- Industrial temperature coverage (بمقابلہA commercial-temperature SOIC-20 transceiver)
- Compact 20-pin surface-mount footprint (بمقابلہA carrier-current interface in a larger through-hole package)
ڈیزائن نوٹس
Place the LM2893MX close to the line-coupling and protection components, and keep the carrier-current path physically separated from sensitive receiver nodes. Route the transmit and receive sections according to the Texas Instruments application circuit rather than treating them as ordinary digital signals. Use a continuous ground reference under the device where the board construction permits, and minimize loop area between the transceiver, coupling network, and protection components.
Design the nominal 18 V supply path for the confirmed 79 mA maximum operating current, allowing margin for temperature, component tolerance, and nearby circuit load. Place local decoupling close to the supply pins and keep high-current and switching-node paths away from the carrier interface. Confirm the correct 13 V to 24 V or 14 V to 30 V operating range for the selected circuit configuration in the manufacturer datasheet before defining the regulator output.
Characterize the carrier line for impedance, noise, and fault conditions before selecting the external coupling and receive-filter values. The LM2893MX supports half-duplex bidirectional serial communication, so receiver discrimination and turnaround behavior are central to link reliability. Use the manufacturer reference interface as the starting point, then validate filtering, attenuation, and data recovery across the required line length, temperature range, and conducted-noise environment.
Do not substitute a standard RS-232 transceiver for the LM2893MX, and do not assume that another 20-pin SOIC device is pin-compatible. Verify signal names, supply limits, carrier-current coupling requirements, and half-duplex behavior against the Texas Instruments pin description. Also avoid allowing surge or mains-coupled energy to reach unprotected transceiver pins; add appropriately rated protection and confirm that its capacitance does not impair receive sensitivity.
تعمیل کی معلومات
RoHS compliance is stated by the LM2893MX product listing. The telecom interface transceiver is not an automotive-qualified AEC-Q100 device, and no separate REACH, lead-free, halogen-free, or conflict-minerals declarations are identified in the verified product information.