LM2902MTX - Quad 1MHz Op Amp | Texas Instruments
MPN: LM2902MTX ✓ 啟用中LM2902MTX 概覽
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2902MTX belongs to the broader hierarchy of operational amplifier, analog amplifier, analog IC, and semiconductor. Unlike rail-to-rail precision amplifiers, this general-purpose family is intended for conventional supply rails and moderate signal bandwidth, making it suitable for cost-sensitive designs where 1 MHz bandwidth is sufficient.
Each of the four amplifier sections provides high open-loop gain and internally compensated operation. A typical non-inverting gain stage uses the amplifier with feedback from its output to the inverting input, while an inverting stage returns the input signal through a feedback network. The shared 14-pin TSSOP package reduces board area compared with four separate single-amplifier packages, and the four independent channels can implement simultaneous sensing, buffering, filtering, or control functions.
The LM2902 family is designed for single-supply or split-supply operation, allowing it to interface with sensors referenced to ground or signals centered between positive and negative rails. Its 1 MHz gain-bandwidth product is adequate for low-frequency control loops, transducer conditioning, and general industrial signal paths, but it is not optimized for high-speed data acquisition or precision applications requiring very low offset voltage, low input bias current, rail-to-rail output swing, or microvolt-level noise.
Typical uses include process-control loops, pressure and temperature sensor interfaces, low-frequency active filters, industrial data acquisition, audio and communication support circuitry, and general buffer stages. Using four independent amplifiers in one package can simplify signal routing and reduce component count when a board needs several similar analog channels.
Designers should verify the input common-mode range, output swing, input bias current, offset voltage, supply current, and stability requirements against the manufacturer datasheet for the exact operating voltage. Input and output networks should be checked for bias-current compensation, and unused amplifier sections should be configured according to the recommended stable-input arrangement rather than left floating.
This product page combines the manufacturer-device identity, package and pin information, operating limits, application guidance, and same-package replacement analysis. It also identifies which electrical characteristics require confirmation from the manufacturer datasheet, helping engineers separate confirmed LM2902MTX attributes from parameters that vary by qualification, temperature grade, or ordering suffix.
直接替換替代品,適用於 LM2902MTX — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2902MTX (相同外形與佔位) — 差異在於 Gain-Bandwidth Product, Product Type, Maximum Supply Voltage, Package, Package Type.
LM2902MTX/NOPB
✅ 直接替換聯絡詢價
查看資料表 →LM2902PT
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LM2902KPWR
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM2902PWR
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM2902MTX/NOPB
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM2902MTX 最大額定值與電氣特性
| Amplifier Count | 4 circuits |
| Product Type | General-purpose operational amplifier |
| Gain-Bandwidth Product | 1 MHz |
| 封裝 | 14-pin TSSOP |
| Package Type | TSSOP (PW) |
| 工作溫度範圍 | -40°C to +85°C |
| 腳位數 | 14 pins |
| 安裝類型 | Surface mount |
| Supply Configuration | Single or split supply |
LM2902MTX 腳位配置
| 腳位 1 | OUT1 — Output of amplifier 1 |
| 腳位 2 | -IN1 — Inverting input of amplifier 1 |
| 腳位 3 | +IN1 — Non-inverting input of amplifier 1 |
| 腳位 4 | V+ — Positive power supply |
| 腳位 5 | +IN2 — Non-inverting input of amplifier 2 |
| 腳位 6 | -IN2 — Inverting input of amplifier 2 |
| 腳位 7 | OUT2 — Output of amplifier 2 |
| 腳位 8 | OUT3 — Output of amplifier 3 |
| 腳位 9 | -IN3 — Inverting input of amplifier 3 |
| 腳位 10 | +IN3 — Non-inverting input of amplifier 3 |
| 腳位 11 | V- — Negative power supply |
| 腳位 12 | +IN4 — Non-inverting input of amplifier 4 |
| 腳位 13 | -IN4 — Inverting input of amplifier 4 |
| 腳位 14 | OUT4 — Output of amplifier 4 |
典型應用
LM2902MTX 適用於 6 應用s: Industrial Process-Control Loops, Temperature and Pressure Sensor Conditioning, Low-Frequency Active Filters, Instrumentation and Data Acquisition, Communication Interface Buffering, Power-Supply Feedback and Monitoring.
Industrial Process-Control Loops
The LM2902MTX fits low-frequency industrial process-control loops because it combines four independent amplifier channels with a 1 MHz gain-bandwidth product in one 14-pin TSSOP. The amplifier can drive error-amplifier, comparator, actuator-conditioning, and signal-return stages around a controller. Its -40°C to +85°C rating is appropriate for industrial equipment, while the compact package reduces board area compared with four separate packages. The principal design checks are output swing, input common-mode range, load stability, and supply headroom.
推薦
Temperature and Pressure Sensor Conditioning
The LM2902MTX can condition resistive temperature and pressure sensors in industrial monitoring equipment. Its four amplifier sections permit differential sensing, reference buffering, active filtering, and output amplification without requiring four packages. The 1 MHz bandwidth provides useful margin for slow sensor signals and compensation networks, while the -40°C to +85°C range supports typical factory environments. Bias-current effects, sensor excitation current, common-mode voltage, and output range must be calculated for the bridge or transmitter used.
推薦
Low-Frequency Active Filters
The LM2902MTX is appropriate for low-frequency active-filter stages that use the Sallen-Key or multiple-feedback topologies. A 1 MHz gain-bandwidth product comfortably supports bandwidths commonly used in audio, measurement, and industrial control when the required closed-loop gain is moderate. Four amplifiers can implement two complete second-order sections or provide buffering and gain stages. Component tolerances and op-amp gain-bandwidth behavior determine actual filter response, so simulation and stability testing should precede high-volume production.
推薦
Instrumentation and Data Acquisition
The LM2902MTX can serve as a front-end amplifier, buffer, or gain stage in low-speed instrumentation and data-acquisition systems. Its four channels allow simultaneous handling of multiple sensor inputs while maintaining a consistent amplifier family and footprint. The 1 MHz bandwidth accommodates many industrial signals, but the design must remain within the input common-mode range and output swing of the selected supply. Input bias-current compensation, source impedance, settling requirements, and channel-to-channel behavior should be verified against the application bandwidth.
推薦
Communication Interface Buffering
The LM2902MTX can buffer slow communication, logic-interface, and level-conversion signals when the signal bandwidth is well below its 1 MHz gain-bandwidth product. Four independent channels are useful for isolating a controller from sensors, amplifiers, or line-driver stages while preserving a common package and pin arrangement. The amplifier is not intended for high-speed digital lines, so rise-time, capacitive-load, output-swing, and supply-voltage checks are essential. Choose an external line driver when current or impedance requirements exceed the amplifier's capabilities.
推薦
Power-Supply Feedback and Monitoring
The LM2902MTX can implement supply-feedback amplifiers, comparators, and monitoring channels in industrial power systems. Its four-channel arrangement allows separate functions such as output-voltage feedback, current monitoring, fault detection, and buffered reference generation. The approximately 1 MHz bandwidth is more than adequate for many control-loop and supervisory functions, while the -40°C to +85°C operating range supports regulated industrial equipment. The power stage, protection network, and operating-point limits must be designed around the actual supply and current requirements.
推薦
推薦產品摘要
工程參考資料,適用於 LM2902MTX — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2902MTX/NOPB | LM2902PT | LM2902KPWR | LM2902PWR | LM2902MT |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin TSSOP (PW) | 14-pin TSSOP (PW) - same footprint | 14-pin TSSOP (PW) - same footprint | 14-pin TSSOP (PW) - same footprint | 14-pin TSSOP (PW) - same footprint | 14-pin TSSOP (PW) - same footprint |
| Amplifier Count | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Gain-Bandwidth Product | 1 MHz | 1 MHz | 1 MHz | 1 MHz | 1 MHz | 1 MHz |
| Number of Pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins |
| Product Category | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Ordering Attribute | Tape-and-reel MTX suffix | Lead-free NOPB finish | PT ordering suffix | KPW tape-and-reel ordering suffix | PW tape-and-reel ordering suffix | MT ordering suffix |
主要差異化特點
- Four amplifier channels in one compact package (對比LM324ANSR)
- Same-footprint lead-free ordering option (對比LM2902MTX/NOPB)
- Industrial temperature range (對比LM2902MTX/NOPB)
- Single- and split-supply flexibility (對比LM2902PT)
設計說明
Do not treat the 14-pin TSSOP pin arrangement as interchangeable with the LM2902DR SOIC-14 option. The LM2902MTX uses the TSSOP PW land pattern, so a SOIC-14 substitute requires a different footprint and solder process. Also avoid leaving an unused amplifier input floating; connect each unused section according to the manufacturer-recommended configuration so bias currents and input-stage behavior remain predictable.
Keep feedback-resistor and compensation networks close to the associated amplifier pins to reduce parasitic capacitance and feedback-loop delay. Source resistance and input-bias current can create DC input offset, so check whether the sensor source needs a bias-current compensation resistor. For capacitive loading, verify the stability limits in the manufacturer characteristics before adding long cable runs or large output-capacitance values.
Design the supply rails around input common-mode range and output-swing requirements rather than assuming the amplifier can drive its output to either rail. Place local supply-bypass capacitors near pins 4 and 11, use short return paths, and keep analog ground routing consistent with the circuit topology. Under single-supply operation, confirm that the signal and sensor references remain inside the usable input range across temperature and load.
Use the manufacturer PW-package land pattern and observe the standard TSSOP lead pitch, body width, solder-mask, and paste recommendations. Although the X suffix indicates a tape-and-reel ordering configuration, it does not change the electrical pinout. Validate the assembly stencil and reflow profile for the selected lead-free process, and inspect exposed-pad requirements if the manufacturer documentation identifies a thermal pad for the exact package revision.
合規資訊
LM2902MTX/NOPB explicitly identifies a no-lead ordering option, but no separate halide-free declaration, REACH declaration, conflict-minerals statement, or AEC-Q100 qualification was established for the exact ordering code. The base LM2902MTX suffix should therefore not be assumed compliant with a specific lead-free procurement requirement without manufacturer confirmation.