LM324ADBR - 30V 1.2MHz Quad Op Amp | Texas Instruments
MPN: LM324ADBR ✓ 啟用中LM324ADBR 概覽
An operational amplifier is a high-gain differential amplifier whose closed-loop behavior is established primarily by external feedback components. The LM324A family combines four amplifiers in one package, placing it in the operational-amplifier hierarchy alongside instrumentation, buffer, and comparator circuits while remaining part of the broader analog and power-management semiconductor ecosystem. Its common-mode input range allows the device to operate from single-supply or split-supply systems.
The LM324ADBR supports a 3 V to 32 V total supply range, has an approximately 1.2 MHz gain-bandwidth product, and specifies a maximum input offset voltage of 3 mV. The package operates from 0°C to 70°C, making the standard A-grade ordering option suitable for commercial and industrial equipment where extended-temperature operation is not required. Its four independent channels can implement non-inverting, inverting, summing, difference, and comparator functions.
Each channel uses a bipolar transistor input stage and an internally compensated architecture. Internal compensation removes the need for an external frequency-compensation capacitor in ordinary closed-loop operation. The 65 dB common-mode rejection and 16 V output swing support precision conditioning of mid-level signals, while the 60 mA per-channel output-current capability provides useful drive for higher-impedance loads.
Typical uses include sensor signal conditioning, low-side current measurement, audio preamplification, transducer interfaces, and general DC signal amplification. The quad configuration also allows a single package to implement a complete instrumentation channel, such as a two-op-amp differential stage plus two buffer or gain stages. The device is especially suitable where a supply voltage above 5 V is available but a rail-to-rail input or output is unnecessary.
Designers should verify common-mode input and output swing against the actual signal range, provide adequate bypassing close to the supply pins, and account for input offset and bias currents in high-impedance measurements. A stable feedback network and adequate output-load capability are also important because the LM324A is optimized for general-purpose, low-frequency precision rather than high-speed or rail-to-rail performance.
This product page combines the Texas Instruments ordering information, package and electrical characteristics, sourcing guidance, and practical design considerations into a focused engineering reference. It also identifies same-footprint family options and explains the trade-offs when comparing the LM324A with lower-cost or lower-performance amplifier implementations.
直接替換替代品,適用於 LM324ADBR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM324ADBR (相同外形與佔位) — 差異在於 Operating Temperature Range, Package.
LM324AIDBR
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LM324ADBR 最大額定值與電氣特性
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Circuits | 4 circuits |
| Maximum Supply Voltage | 30 V |
| Operating Supply Voltage Range | 3 V to 32 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Maximum Input Offset Voltage | 3 mV |
| Input Bias Current | 20 nA |
| Input Offset Current | 0.2 uA |
| Common-Mode Rejection Ratio | 65 dB |
| Output Current per Channel | 60 mA |
| Output Voltage Swing | -16 V to +16 V |
| Supply Current per Channel | 0.2 mA |
| 工作溫度範圍 | 0°C to 70°C |
| 封裝 | 14-pin SSOP (DB) |
| Package Width | 5.30 mm |
| Lead Pitch | 0.209 mm |
| 安裝類型 | Surface mount |
LM324ADBR 腳位配置
| 腳位 1 | OUT1 — Output of amplifier 1 |
| 腳位 2 | IN1- — Inverting input of amplifier 1 |
| 腳位 3 | IN1+ — Non-inverting input of amplifier 1 |
| 腳位 4 | GND — Ground connection |
| 腳位 5 | IN2+ — Non-inverting input of amplifier 2 |
| 腳位 6 | IN2- — Inverting input of amplifier 2 |
| 腳位 7 | OUT2 — Output of amplifier 2 |
| 腳位 8 | OUT3 — Output of amplifier 3 |
| 腳位 9 | IN3- — Inverting input of amplifier 3 |
| 腳位 10 | IN3+ — Non-inverting input of amplifier 3 |
| 腳位 11 | V+ — Positive supply voltage |
| 腳位 12 | IN4+ — Non-inverting input of amplifier 4 |
| 腳位 13 | IN4- — Inverting input of amplifier 4 |
| 腳位 14 | OUT4 — Output of amplifier 4 |
典型應用
LM324ADBR 適用於 6 應用s: Industrial Sensor Signal Conditioning, Low-Side Current Measurement, Audio Preamplification, Transducer Interface, Precision Voltage Divider, Portable Instrumentation.
Industrial Sensor Signal Conditioning
The LM324ADBR is suitable for conditioning signals from sensors that operate within its 3 V to 32 V supply range. Each of the four channels can amplify, filter, buffer, or subtract a sensor voltage, allowing one package to implement several stages of an analog measurement chain. Its 1.2 MHz gain-bandwidth product supports signals well below the amplifier's upper frequency limit, while 65 dB common-mode rejection helps suppress common-mode noise on long industrial wiring connections. The 60 mA per-channel output capability also permits useful drive into moderately resistive loads. Because the LM324A is not rail-to-rail, confirm that both input excursions and output swing remain within the headroom allowed by the selected supply.
推薦
Low-Side Current Measurement
A low-side shunt measurement circuit can use one LM324ADBR channel to amplify the small voltage generated across a current-sense resistor while another channel handles filtering or a reference buffer. The amplifier's 3 mV maximum input offset and 20 nA input bias current are important when the shunt produces only a small signal. A 1.2 MHz gain-bandwidth product permits useful closed-loop bandwidth at practical gain settings, and the 0.2 uA input offset current helps limit error in high-resistance sensing paths. Place the amplifier close to the shunt when possible to minimize pickup from motor and switching systems, and verify that common-mode voltage remains inside the input range.
推薦
Audio Preamplification
The LM324ADBR can implement a four-channel audio preamplifier or mixed-signal input stage when the signal bandwidth is below approximately 1.2 MHz and the supply provides adequate output headroom. Its quad organization reduces the number of packages required for microphone, line, and auxiliary channels. The internally compensated voltage-feedback topology supports conventional inverting and non-inverting gain stages with external resistors and capacitors. The 65 dB common-mode rejection can reduce unwanted hum and coupled noise, although actual audio performance also depends on resistor selection, source impedance, supply decoupling, and grounding. Choose a rail-to-rail low-noise device when the input can approach a supply rail or when lower-noise performance is required.
推薦
Transducer Interface
The four channels in the LM324ADBR can connect resistive, capacitive, or voltage-output transducers to a controller or converter stage. Two channels may form a differential input amplifier, while the remaining channels provide gain, filtering, or output buffering. The device accepts a total supply from 3 V to 32 V, making it adaptable to 5 V, 12 V, or 24 V system rails. Its 60 mA per-channel output current allows moderate load drive, but the output must remain between the practical swing limits rather than being assumed to reach either supply rail. Check the transducer output range and excitation requirements before finalizing the input network.
推薦
Precision Voltage Divider
Two matched LM324ADBR channels can form a precision subtractor for measuring the difference between two voltages, such as the output of a resistive bridge. The 1.2 MHz gain-bandwidth product is more than adequate for slow sensor and instrumentation signals, while the 3 mV maximum offset establishes the baseline input-referred error to consider. A third or fourth channel can provide a low-impedance buffer for downstream conversion. Resistor matching and source impedance determine practical CMRR, so use a common resistor network where practical. The circuit should include a suitable reference and output-scaling stage to keep the amplifier within its common-mode and output-swing limits.
推薦
Portable Instrumentation
The LM324ADBR fits portable battery-powered instrumentation when the rail-to-rail performance of a modern amplifier is not required. Its supply operation begins at 3 V, and four amplifiers in one 14-pin SSOP can provide gain, filtering, level shifting, and buffering within a limited circuit footprint. Low supply current and the compact package help reduce board area, while the 60 mA per-channel output rating covers moderate instrumentation loads. Designers should account for output headroom, input common-mode limits, and the 0°C to 70°C temperature range. For systems operating outside that range, evaluate LM324AIDBR and confirm all grade-specific limits before redesigning the board.
推薦
推薦產品摘要
工程參考資料,適用於 LM324ADBR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM324AIDBR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 14-pin SSOP (DB) | 14-pin SSOP (DB) |
| Amplifier Configuration | Quad | Quad |
| Maximum Supply Voltage | 30 V | 30 V |
| Operating Supply Voltage Range | 3 V to 32 V | 3 V to 32 V |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz |
| Maximum Input Offset Voltage | 3 mV | 3 mV |
| Common-Mode Rejection Ratio | 65 dB | 65 dB |
| Output Current per Channel | 60 mA | 60 mA |
| Operating Temperature Range | 0°C to 70°C | Industrial-temperature grade |
主要差異化特點
- Four general-purpose amplifiers in one compact package (對比LM324AIDBR)
- Wide total supply range (對比LM324AIDBR)
- Moderate output-drive capability (對比LM324AIDBR)
設計說明
Place the supply-bypass capacitor as close as practical to pin 11, and connect pin 4 to the ground plane with a short, low-inductance path. For noise-sensitive signal conditioning, provide local return paths that keep output currents from sharing the input-reference ground segment. The 14-pin SSOP footprint has fine lead pitch, so inspect solder bridging and pad wetting during assembly.
Do not assume rail-to-rail input or output behavior. The input voltage must remain inside the common-mode range, and the output must retain the required headroom below the positive rail and above the negative rail. A 5 V design that attempts to amplify a signal spanning nearly 0 V to 5 V may clip even though the supply itself is within the LM324A operating range.
Keep feedback-resistor networks close to their associated amplifier pins and avoid routing input and output traces in parallel. The 1.2 MHz gain-bandwidth product makes the LM324A suitable mainly for low-frequency and audio-band conditioning, but high closed-loop gain reduces bandwidth and can expose layout instability. Use a stable, low-capacitance feedback topology and verify the completed board with an oscilloscope.
Use a single supply or a split supply only after checking the absolute maximum and common-mode limits. The LM324ADBR supports a 3 V to 32 V total supply and a 30 V maximum rating, but approaching the upper limit reduces design margin for transient overshoot. Select a supply system with controlled startup, adequate decoupling, and a maximum operating voltage below the device limit.
合規資訊
The manufacturer ordering information identifies the LM324ADBR as a standard 0°C to 70°C amplifier in a DB package. No explicit environmental or material-compliance declarations were included in the referenced material.