LM324APWR - Quad 30V 1.2MHz Op Amp | Texas Instruments
MPN: LM324APWR ✓ 啟用中LM324APWR 概覽
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The LM324 belongs to the voltage-feedback operational-amplifier hierarchy, within analog ICs and broader semiconductor electronics. Its four amplifiers can perform independent functions or be configured for differential, summing, filtering, comparison, and feedback-amplifier circuits. This quad organization reduces component count and simplifies PCB layout in multi-channel analog systems.
The LM324A family is optimized for general-purpose requirements rather than high-speed or precision applications. Key characteristics include four amplifier circuits, a 30 V maximum supply, 1.2 MHz gain-bandwidth product, and 3 mV input offset voltage. The LM324APWR temperature grade is specified from 0°C to 70°C, making it suitable for commercial equipment operating within that ambient range. The 14-TSSOP package also supports compact, surface-mounted PCB construction.
The LM324 architecture uses four amplifiers operating from a common positive and negative supply. Its 1.2 MHz gain-bandwidth product is adequate for audio-frequency, sensor-interface, and low-to-moderate-bandwidth feedback loops. The 3 mV input offset specification is the primary limitation for high-precision bridge or current-sense measurements, where offset error can create a meaningful output error after amplification. Designers should calculate the closed-loop gain, output swing, input common-mode range, and required output-current margin for the intended circuit.
Typical applications include four-channel sensor conditioning, industrial control signal interfaces, audio preamplifier stages, low-frequency active filters, and general instrumentation. Multiple LM324 channels can monitor several analog inputs in a controller or provide basic current-to-voltage conversion around resistive sensors. The device is also useful when one circuit needs buffering while other channels perform summing or active-filter functions.
For a new design, verify the 0°C to 70°C temperature range, 30 V maximum supply, and 1.2 MHz bandwidth against the operating requirements. Place decoupling capacitors close to the supply pins, route each amplifier's feedback components close to the corresponding channel, and maintain compatible signal levels around the amplifier inputs. The LM324APWR is most appropriate when low cost, four integrated channels, and broad supply-voltage flexibility outweigh the lower bandwidth and higher offset of precision op amps.
This product page combines manufacturer specifications, package and pin information, application guidance, and constrained drop-in alternatives. It also distinguishes temperature-grade and B-family options by their documented supply range, offset voltage, and operating-temperature differences, helping engineers make a PCB-compatible sourcing decision without confusing electrical equivalence with functional similarity.
直接替換替代品,適用於 LM324APWR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM324APWR (相同外形與佔位) — 差異在於 Amplifier Type, Input Offset Voltage, Package, Gain-Bandwidth Product, Supply Configuration.
LM324BAPWR
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LM324BIPWR
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LM324KAPWRG4
✅ 直接替換聯絡詢價
查看資料表 →LM324APWRG4
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM324BIPWRG4
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LM324APWR 最大額定值與電氣特性
| Number of Amplifiers | 4 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 3 mV |
| 工作溫度範圍 | 0°C to 70°C |
| 封裝 | 14-pin TSSOP (PW) |
| 腳位數 | 14 pins |
| 安裝類型 | Surface mount |
| Supply Configuration | Single or dual supply |
LM324APWR 腳位配置
| 腳位 1 | OUT1 — Output of amplifier 1 |
| 腳位 2 | IN1- — Inverting input of amplifier 1 |
| 腳位 3 | IN1+ — Non-inverting input of amplifier 1 |
| 腳位 4 | V+ — Positive supply connection |
| 腳位 5 | IN2+ — Non-inverting input of amplifier 2 |
| 腳位 6 | IN2- — Inverting input of amplifier 2 |
| 腳位 7 | OUT2 — Output of amplifier 2 |
| 腳位 8 | OUT3 — Output of amplifier 3 |
| 腳位 9 | IN3- — Inverting input of amplifier 3 |
| 腳位 10 | IN3+ — Non-inverting input of amplifier 3 |
| 腳位 11 | V- — Negative supply connection or ground in single-supply operation |
| 腳位 12 | IN4+ — Non-inverting input of amplifier 4 |
| 腳位 13 | IN4- — Inverting input of amplifier 4 |
| 腳位 14 | OUT4 — Output of amplifier 4 |
典型應用
LM324APWR 適用於 6 應用s: Industrial Sensor Signal Conditioning, Audio Preamplifier and Mixer, Control-System Analog Interface, Low-Frequency Active Filters, Portable Measurement Module, Test and Measurement Front End.
Industrial Sensor Signal Conditioning
The LM324APWR suits industrial sensor-conditioning modules that must buffer or modestly amplify several low-bandwidth inputs. Its four channels provide independent amplifier sections in one 14-pin TSSOP, reducing component count on a compact controller board. The 1.2 MHz gain-bandwidth product is appropriate for common temperature, pressure, and position signals, while single- or dual-supply operation simplifies interface design around 5 V or higher rails. The main engineering check is the 3 mV input offset: at high noise gain it can create a meaningful output error. Designers should compare that error with sensor resolution and include calibration or a lower-offset amplifier when the measurement demands greater accuracy.
推薦
Audio Preamplifier and Mixer
The LM324APWR can implement four general-purpose audio preamplifier, summing, or mixing stages where bandwidth beyond the audio band is unnecessary. Its 1.2 MHz gain-bandwidth product provides useful closed-loop margin for low- to mid-frequency audio paths, and the four amplifiers allow a compact stereo or multichannel front end. The 30 V maximum supply also permits higher-compliance signal handling when the circuit operates from a dual rail. Audio designers should keep each channel's feedback network compact, verify output swing against the chosen supply, and avoid using the 3 mV input offset as a substitute for DC bias design when the source operates near ground.
推薦
Control-System Analog Interface
The LM324APWR is appropriate for general industrial control interfaces that amplify command and feedback signals at modest bandwidths. Four channels can be allocated to a command buffer, a feedback amplifier, an error amplifier, and a monitoring channel while sharing the same supply pins. The 0°C to 70°C operating range matches many commercial control environments, and the 30 V limit supports dual-rail or higher-voltage interface designs within the electrical limits. Because the LM324 is not rail-to-rail by specification, the designer should verify input common-mode range and output swing at every operating point. Stable feedback ratios and short ground-return paths are especially important in systems sharing noisy actuator power.
推薦
Low-Frequency Active Filters
The LM324APWR can build first- or second-order low-frequency active filters, buffers, and notch stages because its four channels provide enough flexibility for multi-pole arrangements. The 1.2 MHz gain-bandwidth product is normally well above the corner frequencies used in voice-band, sensor-band, or slow industrial-control filtering. Passive resistor and capacitor values determine the response, so component tolerances and the amplifier's 3 mV offset can influence cutoff accuracy and DC output. Keep each amplifier's compensation and feedback components close to its pins, use a stable low-noise ground reference, and confirm stability with the actual load. The TSSOP footprint also permits compact filter modules where analog routing is more constrained than board area.
推薦
Portable Measurement Module
The LM324APWR suits portable, battery-powered measurement modules that require several low-power analog channels from a compact package. A single-supply configuration can simplify the power tree, while four amplifier sections can handle sensor buffers, gain stages, or an output driver. The 1.2 MHz gain-bandwidth product is sufficient for many slow-moving measurements, but the device remains a general-purpose amplifier rather than a micropower part. Battery design must therefore evaluate the device's actual quiescent current and output-current demand under the intended load. Signal-ground and supply-return routing should be kept short so switching converter ripple does not add to sensor noise or disturb the 3 mV input-offset budget.
推薦
Test and Measurement Front End
The LM324APWR can serve as a general-purpose front end in low-bandwidth test and measurement equipment, including buffer, comparator, and error-amplifier stages. Its four circuits reduce the number of packages needed for a multi-channel instrument, and the 1.2 MHz gain-bandwidth product covers many process-control and analog diagnostic signals. For precision measurement, however, engineers must account for the 3 mV input offset and the output error it creates after amplification. The 0°C to 70°C rating is appropriate for standard laboratory-class equipment but not extended industrial environments. Use short, shielded signal paths, stable references, and careful grounding to prevent the quad amplifier's shared supply connections from coupling noise between channels.
推薦
推薦產品摘要
工程參考資料,適用於 LM324APWR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM324BAPWR | LM324BIPWR | LM324KAPWRG4 | LM324APWRG4 | LM324BIPWRG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-TSSOP (PW) | 14-TSSOP (PW) | 14-TSSOP (PW) | 14-TSSOP (PW) | 14-TSSOP (PW) | 14-TSSOP (PW) |
| Number of Amplifiers | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Maximum Supply Voltage | 30 V | 36 V | 36 V | 30 V | 30 V | 36 V |
| Pin Count | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins |
主要差異化特點
- Four general-purpose amplifiers in one 14-pin TSSOP (對比LM324ANSR)
- Higher maximum supply rating in the B family (對比LM324BAPWR)
- Broader environmental coverage with the K-grade option (對比LM324KAPWRG4)
- Commercial temperature option for standard environments (對比LM324BIPWR)
設計說明
Place the positive and negative supply-decoupling capacitors immediately adjacent to pins 4 and 11, with short ground returns and no shared high-current paths between amplifier channels. Route each feedback resistor and capacitor close to its associated amplifier to minimize parasitic capacitance and prevent one channel's feedback loop from coupling into another. Preserve a continuous ground reference beneath the TSSOP footprint when practical, and avoid routing sensitive input traces parallel to switching-converter or motor-drive currents.
Do not assume the LM324APWR input or output can swing rail to rail. Check each signal's common-mode range and required output amplitude against the manufacturer's recommended operating conditions, especially in 5 V single-supply designs. Also calculate output-error contribution from the 3 mV input offset at the actual noise gain. If offset drift or error exceeds the measurement resolution, use calibration or move to a lower-offset amplifier rather than increasing gain without checking the resulting error.
The 30 V maximum supply rating is an absolute device limit, not a recommended operating point. Provide adequate input-voltage headroom for the chosen topology and account for transients from wiring, inductors, or actuator loads. When using a dual supply, ensure that the total voltage between pins 4 and 11 never exceeds 30 V. For single-supply operation, use pin 11 as the circuit reference and establish any mid-supply bias explicitly; do not rely on the amplifier inputs to create it automatically.
The 1.2 MHz gain-bandwidth product must be considered together with the closed-loop noise gain. A high-gain stage requires proportionally more amplifier bandwidth, while a capacitive load can reduce stability margin. Follow the manufacturer datasheet for output-capacitance and stability guidance, keep feedback loops compact, and isolate long sensor wiring from sensitive inputs. For slow measurement systems, add filtering near the source so that out-of-band noise does not consume the amplifier's finite bandwidth or disturb the selected gain.
The LM324APWR is normally not thermally limited in ordinary low-bandwidth signal-conditioning service, but power dissipation rises with supply voltage, output current, and channel activity. Estimate worst-case dissipation from the actual supply and output operating points, then verify the ambient-temperature range against the 0°C to 70°C specification. The small TSSOP package benefits from short thermal paths and adequate PCB copper, especially when all four channels operate continuously near the maximum supply rating.
合規資訊
Compliance declarations were not stated in the available manufacturer and distributor listings. Verify the current declarations and ordering qualification for the exact suffix before production release.