Texas Instruments

LM324APWR - Quad 30V 1.2MHz Op Amp | Texas Instruments

MPN: LM324APWR ✓ Hoạt động
30 V Vdss 14-pin TSSOP (PW) Package
MOQ: 1 |

LM324APWR Tóm tắt

The Texas Instruments LM324APWR is a four-circuit general-purpose operational amplifier designed for single- or dual-supply operation. It provides a maximum supply rating of 30 V, a gain-bandwidth product of 1.2 MHz, input offset voltage of 3 mV, and four amplifiers in a 14-pin TSSOP package. The LM324APWR is intended for cost-sensitive analog signal conditioning, instrumentation, and control applications.

An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The LM324 belongs to the voltage-feedback operational-amplifier hierarchy, within analog ICs and broader semiconductor electronics. Its four amplifiers can perform independent functions or be configured for differential, summing, filtering, comparison, and feedback-amplifier circuits. This quad organization reduces component count and simplifies PCB layout in multi-channel analog systems.

The LM324A family is optimized for general-purpose requirements rather than high-speed or precision applications. Key characteristics include four amplifier circuits, a 30 V maximum supply, 1.2 MHz gain-bandwidth product, and 3 mV input offset voltage. The LM324APWR temperature grade is specified from 0°C to 70°C, making it suitable for commercial equipment operating within that ambient range. The 14-TSSOP package also supports compact, surface-mounted PCB construction.

The LM324 architecture uses four amplifiers operating from a common positive and negative supply. Its 1.2 MHz gain-bandwidth product is adequate for audio-frequency, sensor-interface, and low-to-moderate-bandwidth feedback loops. The 3 mV input offset specification is the primary limitation for high-precision bridge or current-sense measurements, where offset error can create a meaningful output error after amplification. Designers should calculate the closed-loop gain, output swing, input common-mode range, and required output-current margin for the intended circuit.

Typical applications include four-channel sensor conditioning, industrial control signal interfaces, audio preamplifier stages, low-frequency active filters, and general instrumentation. Multiple LM324 channels can monitor several analog inputs in a controller or provide basic current-to-voltage conversion around resistive sensors. The device is also useful when one circuit needs buffering while other channels perform summing or active-filter functions.

For a new design, verify the 0°C to 70°C temperature range, 30 V maximum supply, and 1.2 MHz bandwidth against the operating requirements. Place decoupling capacitors close to the supply pins, route each amplifier's feedback components close to the corresponding channel, and maintain compatible signal levels around the amplifier inputs. The LM324APWR is most appropriate when low cost, four integrated channels, and broad supply-voltage flexibility outweigh the lower bandwidth and higher offset of precision op amps.

This product page combines manufacturer specifications, package and pin information, application guidance, and constrained drop-in alternatives. It also distinguishes temperature-grade and B-family options by their documented supply range, offset voltage, and operating-temperature differences, helping engineers make a PCB-compatible sourcing decision without confusing electrical equivalence with functional similarity.

Bộ thay thế dễ dàng lắp đặt cho LM324APWR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM324APWR (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Input Offset Voltage, Package, Gain-Bandwidth Product, Supply Configuration.

Texas Instruments
Amplifier Type: Quad general-purpose operational amplifier
Input Offset Voltage: 2 mV
So sánh với LM324APWR →
onsemi
Package: 14-pin TSSOP
So sánh với LM324APWR →
onsemi
Input Offset Voltage: 3 mV typical
Package: 14-pin TSSOP
Gain-Bandwidth Product: Approximately 1 MHz
So sánh với LM324APWR →
Texas Instruments
Amplifier Type: Quad general-purpose operational amplifier, unity-gain stable
Input Offset Voltage: ±3 mV typ (LM324A grade)
Package: 14-pin TSSOP (PW), 0.8 mm pitch
So sánh với LM324APWR →
STMicroelectronics
Amplifier Type: Standard (General Purpose) Operational Amplifier
Gain-Bandwidth Product: 1.3 MHz typical
So sánh với LM324APWR →
onsemi
Input Offset Voltage: 5 mV maximum
Package: 14-pin TSSOP
So sánh với LM324APWR →
Texas Instruments
Amplifier Type: Quad general-purpose operational amplifier
Package: 14-pin TSSOP
So sánh với LM324APWR →
Texas Instruments
Package: 14-TSSOP
So sánh với LM324APWR →
Texas Instruments
Package: 14-pin TSSOP
So sánh với LM324APWR →
Texas Instruments
Amplifier Type: Quad operational amplifier
Package: 14-TSSOP
So sánh với LM324APWR →
Texas Instruments
Amplifier Type: Single operational amplifier
Supply Configuration: Single power supply
Texas Instruments
Package: 14-TSSOP
Supply Configuration: Single supply or split supply
So sánh với LM324APWR →

LM324BAPWR

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 14-TSSOP (PW)
Supply rating increases from 30 V to 36 V, a 20% increase, while BA-version offset is listed as ±2 mV versus 3 mV.

📋 Tham chiếu thay thế (không có trong danh mục)

LM324BIPWR

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 14-TSSOP (PW)
Uses the same 30 V-class LM324 amplifier architecture in 14-pin PW, with the I-grade operating range extended to -40°C to 125°C from 0°C to 70°C.

📋 Tham chiếu thay thế (không có trong danh mục)

LM324KAPWRG4

✅ Drop-In
Texas Instruments
📦 14-TSSOP (PW)
Quad general-purpose operational amplifier · 4 circuits · 14-TSSOP · Surface mount · Single or dual supply · 26 V · 13 V per rail · 0.8 mA

Liên hệ để biết giá

Xem tài liệu →

LM324APWRG4

✅ Drop-In ⚠️ Thông số chưa được xác minh
Texas Instruments
📦 14-TSSOP (PW)
4 · Quad general-purpose operational amplifier, unity-gain stable · ±16 V (32 V max total supply) · ±3 mV typ (LM324A grade) · 0.8 mA typ, independent of supply voltage · 2 kV · Includes ground, allowing direct sensing at 0 V · 14

Liên hệ để biết giá

Xem tài liệu →

LM324BIPWRG4

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 14-TSSOP (PW)
Combines the B-family 3 V to 36 V supply capability with a -40°C to 125°C I-grade range versus LM324APWR's 0°C to 70°C range.

📋 Tham chiếu thay thế (không có trong danh mục)

LM324APWR Tỷ lệ tối đa & tính chất điện

Number of Amplifiers 4 circuits
Amplifier Type General-purpose operational amplifier
Maximum Supply Voltage 30 V
Gain-Bandwidth Product 1.2 MHz
Input Offset Voltage 3 mV
Khoảng nhiệt độ hoạt động 0°C to 70°C
Hộp 14-pin TSSOP (PW)
Số lượng chân 14 pins
Kiểu lắp đặt Surface mount
Supply Configuration Single or dual supply

Cấu hình chân LM324APWR

TSSOP-14 (4.4mm) Package Pinout Diagram TSSOP-14 4.4x5mm, P0.65mm, JEDEC MO-153. 14-pin thin shrink. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 TSSOP-14 (4.4mm)
Chân 1 OUT1 — Output of amplifier 1
Chân 2 IN1- — Inverting input of amplifier 1
Chân 3 IN1+ — Non-inverting input of amplifier 1
Chân 4 V+ — Positive supply connection
Chân 5 IN2+ — Non-inverting input of amplifier 2
Chân 6 IN2- — Inverting input of amplifier 2
Chân 7 OUT2 — Output of amplifier 2
Chân 8 OUT3 — Output of amplifier 3
Chân 9 IN3- — Inverting input of amplifier 3
Chân 10 IN3+ — Non-inverting input of amplifier 3
Chân 11 V- — Negative supply connection or ground in single-supply operation
Chân 12 IN4+ — Non-inverting input of amplifier 4
Chân 13 IN4- — Inverting input of amplifier 4
Chân 14 OUT4 — Output of amplifier 4

Ứng dụng tiêu biểu

LM324APWR phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Audio Preamplifier and Mixer, Control-System Analog Interface, Low-Frequency Active Filters, Portable Measurement Module, Test and Measurement Front End.

🏭

Industrial Sensor Signal Conditioning

The LM324APWR suits industrial sensor-conditioning modules that must buffer or modestly amplify several low-bandwidth inputs. Its four channels provide independent amplifier sections in one 14-pin TSSOP, reducing component count on a compact controller board. The 1.2 MHz gain-bandwidth product is appropriate for common temperature, pressure, and position signals, while single- or dual-supply operation simplifies interface design around 5 V or higher rails. The main engineering check is the 3 mV input offset: at high noise gain it can create a meaningful output error. Designers should compare that error with sensor resolution and include calibration or a lower-offset amplifier when the measurement demands greater accuracy.

🎧

Audio Preamplifier and Mixer

The LM324APWR can implement four general-purpose audio preamplifier, summing, or mixing stages where bandwidth beyond the audio band is unnecessary. Its 1.2 MHz gain-bandwidth product provides useful closed-loop margin for low- to mid-frequency audio paths, and the four amplifiers allow a compact stereo or multichannel front end. The 30 V maximum supply also permits higher-compliance signal handling when the circuit operates from a dual rail. Audio designers should keep each channel's feedback network compact, verify output swing against the chosen supply, and avoid using the 3 mV input offset as a substitute for DC bias design when the source operates near ground.

🔧

Control-System Analog Interface

The LM324APWR is appropriate for general industrial control interfaces that amplify command and feedback signals at modest bandwidths. Four channels can be allocated to a command buffer, a feedback amplifier, an error amplifier, and a monitoring channel while sharing the same supply pins. The 0°C to 70°C operating range matches many commercial control environments, and the 30 V limit supports dual-rail or higher-voltage interface designs within the electrical limits. Because the LM324 is not rail-to-rail by specification, the designer should verify input common-mode range and output swing at every operating point. Stable feedback ratios and short ground-return paths are especially important in systems sharing noisy actuator power.

📡

Low-Frequency Active Filters

The LM324APWR can build first- or second-order low-frequency active filters, buffers, and notch stages because its four channels provide enough flexibility for multi-pole arrangements. The 1.2 MHz gain-bandwidth product is normally well above the corner frequencies used in voice-band, sensor-band, or slow industrial-control filtering. Passive resistor and capacitor values determine the response, so component tolerances and the amplifier's 3 mV offset can influence cutoff accuracy and DC output. Keep each amplifier's compensation and feedback components close to its pins, use a stable low-noise ground reference, and confirm stability with the actual load. The TSSOP footprint also permits compact filter modules where analog routing is more constrained than board area.

📱

Portable Measurement Module

The LM324APWR suits portable, battery-powered measurement modules that require several low-power analog channels from a compact package. A single-supply configuration can simplify the power tree, while four amplifier sections can handle sensor buffers, gain stages, or an output driver. The 1.2 MHz gain-bandwidth product is sufficient for many slow-moving measurements, but the device remains a general-purpose amplifier rather than a micropower part. Battery design must therefore evaluate the device's actual quiescent current and output-current demand under the intended load. Signal-ground and supply-return routing should be kept short so switching converter ripple does not add to sensor noise or disturb the 3 mV input-offset budget.

🖥️

Test and Measurement Front End

The LM324APWR can serve as a general-purpose front end in low-bandwidth test and measurement equipment, including buffer, comparator, and error-amplifier stages. Its four circuits reduce the number of packages needed for a multi-channel instrument, and the 1.2 MHz gain-bandwidth product covers many process-control and analog diagnostic signals. For precision measurement, however, engineers must account for the 3 mV input offset and the output error it creates after amplification. The 0°C to 70°C rating is appropriate for standard laboratory-class equipment but not extended industrial environments. Use short, shielded signal paths, stable references, and careful grounding to prevent the quad amplifier's shared supply connections from coupling noise between channels.

Tóm tắt các sản phẩm được đề xuất

LM324ANSR Texas Instruments Được sử dụng trong: Industrial Sensor Signal Conditioning, Audio Preamplifier and Mixer, Control-System Analog Interface, Portable Measurement Module LM324KAPWRG4 Texas Instruments Được sử dụng trong: Industrial Sensor Signal Conditioning, Control-System Analog Interface, Test and Measurement Front End LM324BAPWR Related B-family quad amplifier with lower listed offset Được sử dụng trong: Audio Preamplifier and Mixer, Low-Frequency Active Filters LM324BIPWR Related industrial-temperature quad amplifier Được sử dụng trong: Low-Frequency Active Filters, Test and Measurement Front End LM324APWRG4 Texas Instruments Được sử dụng trong: Portable Measurement Module
What are the key specifications of LM324APWR that engineers should know?
The LM324APWR is a four-circuit general-purpose operational amplifier with a 30 V maximum supply, 1.2 MHz gain-bandwidth product, 3 mV input offset voltage, and a 14-pin TSSOP package. According to the Texas Instruments LM324A product page and manufacturer datasheet, it is rated for a 0°C to 70°C ambient temperature range. The quad configuration places four amplifiers in one package, reducing board area compared with four separate single op amps while retaining general-purpose versatility.
Where to download the LM324APWR datasheet PDF?
The official LM324A product page at Texas Instruments provides the manufacturer datasheet and ordering information for the LM324APWR. The LM324APWR ordering option is identified as a 14-pin PW-package device. Use the manufacturer datasheet for the complete electrical characteristics, pin descriptions, recommended operating conditions, and application guidance. The searchable TI product URL is https://www.ti.com/product/LM324A and is the preferred source for revisions of the technical documentation.
Where can I find the LM324APWR pinout?
The LM324APWR pinout is documented in the Texas Instruments LM324A manufacturer datasheet and uses the standard 14-pin TSSOP arrangement. Channels one and two occupy pins 1 through 8, channels three and four occupy pins 9 through 14, and the common power connections are pins 4 and 11. Verify signal names and exposed-pad treatment against the specific ordering data sheet before laying out a PCB.
What is the operating voltage range of LM324APWR?
The LM324APWR supports single- or dual-supply operation with a maximum total supply rating of 30 V. The manufacturer identifies the LM324A as a 30 V quad operational amplifier, while the B-family versions listed by Texas Instruments extend the supply range to 36 V. For LM324APWR designs, remain within the 30 V limit and observe the input common-mode and output-swing limits specified in the manufacturer datasheet.
Can LM324APWR operate on a single 5V supply?
Yes, the LM324APWR can operate from a single 5 V supply because it supports single- and dual-supply operation. Its usable input and output ranges must remain within the common-mode and swing limits stated in the Texas Instruments LM324A datasheet. A single-supply design should bias the signal around mid-supply when the input waveform can reach or cross ground, and it should avoid driving the output beyond the specified swing.
Is LM324APWR suitable for sensor signal conditioning?
The LM324APWR is suitable for many low-bandwidth sensor-conditioning tasks because it combines four amplifiers, a 1.2 MHz gain-bandwidth product, and operation from a single or dual supply. Its 3 mV input offset can be significant with high-gain sensor measurements, so compare that value against the smallest signal being amplified. Buffering, differential amplification, and modest gain stages are typical uses, while precision bridge measurements may require lower-offset amplification.
What is the gain-bandwidth product of LM324APWR?
The LM324APWR has a gain-bandwidth product of 1.2 MHz. According to the Texas Instruments LM324A product page, this bandwidth supports general-purpose feedback networks operating at low or moderate frequencies. Practical closed-loop bandwidth also depends on noise gain, load, stability, and the selected compensation network, so use the manufacturer datasheet for a complete AC characterization rather than treating 1.2 MHz as the usable signal bandwidth at every gain.
How much input offset voltage does LM324APWR have?
The specified input offset voltage of LM324APWR is 3 mV. This is the differential voltage that must appear between the inputs for the output to reach its ideal zero-volt condition. In a practical amplifier, offset voltage is multiplied by the closed-loop noise gain and may also be corrected through calibration. The 3 mV rating makes the device appropriate for general-purpose conditioning rather than precision applications requiring offsets in the microvolt range.
Where to buy LM324APWR online and what is the current lead time?
Use the Request a Quote form on this page to request LM324APWR availability, current lead time, and order quantities from XAIPART. The Request a Quote workflow also helps confirm the desired package, shipment quantity, and traceability requirements. Current stock and lead time can change, so obtain a written quotation before committing the component to a production schedule or building a time-critical procurement plan.
What is the price of LM324APWR?
The current commercial price for LM324APWR is best obtained through the Request a Quote form on this page. Pricing can vary with order quantity, package handling, delivery requirements, and market conditions, so a quotation reflects the actual quantity and commercial terms for the order. Submit the required part number, quantity, and shipment destination through that form to receive the applicable offer.
Is LM324APWR in stock?
LM324APWR availability should be confirmed through the Request a Quote form on this page because stock changes with order size and replenishment activity. Include the required quantity, delivery date, and any traceability or inspection requirements in the request. For production planning, treat the confirmed response as the supply commitment rather than assuming that an active catalog status guarantees immediate inventory.
LM324APWR vs LM324BAPWR - which is better for a 36V supply design?
LM324BAPWR is the better choice when the supply can reach 36 V because Texas Instruments lists the B-version supply range as 3 V to 36 V and its BA-version offset voltage as ±2 mV. LM324APWR is rated to 30 V with 3 mV offset. Both belong to the same LM324 family, but the B version adds a 6 V, or 20%, increase in maximum supply rating and a 1 mV reduction in listed offset magnitude.
What is the difference between LM324APWR and LM324KAPWRG4?
The principal documented selection difference is operating-temperature grade. LM324APWR is specified for 0°C to 70°C, while the LM324KAPWRG4 military-qualified ordering option supports an extended -55°C to 125°C range and uses the same 14-pin PW package. Both are general-purpose 30 V, 1.2 MHz, four-channel amplifiers. The K-grade device is preferable when environmental qualification, rather than offset or bandwidth, drives the replacement.
When should I choose LM324APWR over a higher-precision amplifier?
Choose LM324APWR when four channels, a 30 V supply capability, and a cost-conscious general-purpose implementation matter more than microvolt-level offset, high bandwidth, or rail-to-rail output. Its 1.2 MHz gain-bandwidth product and 3 mV offset are appropriate for audio-frequency buffers, basic filters, control loops, and moderate-gain sensor interfaces. Select a precision amplifier when the output error caused by 3 mV input offset would exceed the measurement requirement.
What can replace LM324APWR without changing the PCB?
LM324BAPWR, LM324BIPWR, LM324KAPWRG4, LM324APWRG4, and LM324BIPWRG4 are same-family, 14-pin PW-package candidates for PCB-compatible sourcing. Their suitability depends on supply voltage, temperature grade, offset, qualification, and exact suffix configuration. According to Texas Instruments, LM324B versions are drop-in replacements for LM324 and LM2902 families, with B versions extending supply operation to 36 V. Confirm the full ordering data before substituting any grade.
Is LM324APWR the same as LM324APW?
LM324APWR and LM324APW refer to closely related 14-pin PW-package ordering options, but the suffix can encode different reel or packing conventions. The electrical device family is the same, and the manufacturer lists both under LM324A. For PCB compatibility, use the package drawing and exposed-pad details for the exact suffix. For production procurement, submit the complete MPN rather than treating the base and reel-suffix forms as identical ordering codes.

Dữ liệu tham khảo kỹ thuật cho LM324APWR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose LM324APWR for general-purpose analog designs requiring four amplifiers, a 30 V maximum supply, and operation from 0°C to 70°C. It is well suited to low-bandwidth sensor buffering, audio preamplification, active filtering, and basic control interfaces where 1.2 MHz bandwidth and 3 mV input offset are acceptable. Select LM324BAPWR when the circuit can reach 36 V or benefits from the lower ±2 mV BA-version offset. Choose LM324BIPWR for a -40°C to 125°C industrial temperature range, and LM324KAPWRG4 or LM324APWRG4 for -55°C to 125°C environmental coverage. All listed alternatives use the 14-pin PW package, but suffix-level qualification, packing, and ordering details must still be confirmed. If the design requires microvolt-level offset, rail-to-rail input or output, substantially higher bandwidth, or low quiescent current, move to a more specialized amplifier family rather than treating a general-purpose LM324 variant as interchangeable.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này LM324BAPWR LM324BIPWR LM324KAPWRG4 LM324APWRG4 LM324BIPWRG4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 14-TSSOP (PW) 14-TSSOP (PW) 14-TSSOP (PW) 14-TSSOP (PW) 14-TSSOP (PW) 14-TSSOP (PW)
Number of Amplifiers 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits
Maximum Supply Voltage 30 V 36 V 36 V 30 V 30 V 36 V
Pin Count 14 pins 14 pins 14 pins 14 pins 14 pins 14 pins

Bảo phân biệt quan trọng

  • Four general-purpose amplifiers in one 14-pin TSSOP (vsLM324ANSR)
  • Higher maximum supply rating in the B family (vsLM324BAPWR)
  • Broader environmental coverage with the K-grade option (vsLM324KAPWRG4)
  • Commercial temperature option for standard environments (vsLM324BIPWR)

Ghi chú thiết kế

Place the positive and negative supply-decoupling capacitors immediately adjacent to pins 4 and 11, with short ground returns and no shared high-current paths between amplifier channels. Route each feedback resistor and capacitor close to its associated amplifier to minimize parasitic capacitance and prevent one channel's feedback loop from coupling into another. Preserve a continuous ground reference beneath the TSSOP footprint when practical, and avoid routing sensitive input traces parallel to switching-converter or motor-drive currents.

Do not assume the LM324APWR input or output can swing rail to rail. Check each signal's common-mode range and required output amplitude against the manufacturer's recommended operating conditions, especially in 5 V single-supply designs. Also calculate output-error contribution from the 3 mV input offset at the actual noise gain. If offset drift or error exceeds the measurement resolution, use calibration or move to a lower-offset amplifier rather than increasing gain without checking the resulting error.

The 30 V maximum supply rating is an absolute device limit, not a recommended operating point. Provide adequate input-voltage headroom for the chosen topology and account for transients from wiring, inductors, or actuator loads. When using a dual supply, ensure that the total voltage between pins 4 and 11 never exceeds 30 V. For single-supply operation, use pin 11 as the circuit reference and establish any mid-supply bias explicitly; do not rely on the amplifier inputs to create it automatically.

The 1.2 MHz gain-bandwidth product must be considered together with the closed-loop noise gain. A high-gain stage requires proportionally more amplifier bandwidth, while a capacitive load can reduce stability margin. Follow the manufacturer datasheet for output-capacitance and stability guidance, keep feedback loops compact, and isolate long sensor wiring from sensitive inputs. For slow measurement systems, add filtering near the source so that out-of-band noise does not consume the amplifier's finite bandwidth or disturb the selected gain.

The LM324APWR is normally not thermally limited in ordinary low-bandwidth signal-conditioning service, but power dissipation rises with supply voltage, output current, and channel activity. Estimate worst-case dissipation from the actual supply and output operating points, then verify the ambient-temperature range against the 0°C to 70°C specification. The small TSSOP package benefits from short thermal paths and adequate PCB copper, especially when all four channels operate continuously near the maximum supply rating.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

Compliance declarations were not stated in the available manufacturer and distributor listings. Verify the current declarations and ordering qualification for the exact suffix before production release.

Dữ liệu được xác minh vào: 2026-11-17 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

LM324APWR LM324APWR datasheet LM324APWR datasheet pdf LM324APWR pinout LM324APWR equivalent LM324APWR replacement LM324APWR cross reference LM324APWR vs LM324BAPWR LM324APWR vs LM324KAPWRG4 Texas Instruments LM324APWR LM324APWR TSSOP-14 LM324APWR 30V 1.2MHz LM324APWR price LM324APWR stock LM324APWR sensor signal conditioning

Các bộ phận và thuật ngữ liên quan

Texas Instruments LM324APWR LM324A LM324BAPWR LM324BIPWR LM324KAPWRG4 LM324APWRG4 LM324BIPWRG4 LM324ANSR quad operational amplifier operational amplifier voltage-feedback amplifier analog integrated circuit semiconductor general-purpose amplifier 14-TSSOP PW package TSSOP family surface-mount package SMD input offset voltage gain-bandwidth product single-supply operation dual-supply operation sensor signal conditioning active filter industrial control audio preamplifier
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ