LM393APS - Dual 18V/36V Open-Collector Comparator | Texas Instruments
MPN: LM393APS ✓ 啟用中LM393APS 概覽
A comparator is an analog integrated circuit that evaluates the relative voltage applied to its inverting and non-inverting inputs. The LM393APS is therefore placed in the feedback path of control, sensing, or protection circuits rather than amplifying a signal directly. Its open-collector outputs can sink current from an external pull-up network, which allows wired logic interconnection, level translation, and relay-driver interfaces without requiring a dedicated push-pull output stage.
Key characteristics of this dual comparator include two independent channels, an open-collector output topology, rail-to-rail input handling, and an 8-pin surface-mount package. The open-collector arrangement also requires an external pull-up resistor when the output must reach a valid high logic level. The SOIC-8 footprint simplifies assembly on modern surface-mount boards while preserving the pin arrangement associated with the LM393AP family.
Internally, each LM393APS channel compares two input voltages and changes its output state according to their relationship. Because the outputs are open collector, the device can interface with TTL, CMOS, or other pull-up-defined logic rails when voltage and current limits are respected. The shared supply and ground pins make the two channels useful for window comparison, overvoltage detection, sensor thresholding, and complementary control decisions.
Typical uses include industrial sensor interfaces, battery and power-supply monitoring, temperature threshold circuits, motor or actuator control, loop-error detection, and general logic level conversion. Because the output transistor can remain off in the fault state, the open-collector structure is especially useful where a wired-AND behavior or fail-safe output is desirable.
When laying out a board, place the pull-up resistor close to the output net and route comparator inputs away from switching nodes and high-current traces. Confirm the absolute maximum supply voltage, input common-mode limits, output current, and propagation timing in the manufacturer datasheet before applying the device to a new design.
This page combines package identification, pin assignments, application guidance, comparison criteria, and design cautions to support faster component selection and PCB planning.
直接替換替代品,適用於 LM393APS — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM393APS (相同外形與佔位) — 差異在於 Output Type, Package, Common-Mode Input Range, Comparator Type, Input Offset Voltage.
LM393B
✅ 直接替換📋 參考替代品(不在目錄中)
LM393LV
✅ 直接替換📋 參考替代品(不在目錄中)
LM393AD
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM393BD
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LM393APS 最大額定值與電氣特性
| Comparator Type | Dual differential voltage comparator |
| Number of Channels | 2 channels |
| 供應電壓 | 18 V / 36 V |
| 輸出類型 | Open-collector |
| Input Common-Mode Range | Rail-to-rail |
| 封裝 | 8-pin small-outline package (SOP-8) |
| 安裝類型 | Surface mount |
| 腳位數 | 8 pins |
| RoHS Compliance | Unknown |
| REACH Compliance | Unknown |
| Automotive AEC-Q100 Qualification | Not applicable |
LM393APS 腳位配置
| 腳位 1 | OUT 1 — Open-collector output of comparator channel 1 |
| 腳位 2 | IN 1- — Inverting input of comparator channel 1 |
| 腳位 3 | IN 1+ — Non-inverting input of comparator channel 1 |
| 腳位 4 | GND — Ground connection |
| 腳位 5 | IN 2+ — Non-inverting input of comparator channel 2 |
| 腳位 6 | IN 2- — Inverting input of comparator channel 2 |
| 腳位 7 | OUT 2 — Open-collector output of comparator channel 2 |
| 腳位 8 | VCC — Positive supply connection |
典型應用
LM393APS 適用於 6 應用s: Industrial Sensor Threshold Detection, Battery Voltage Monitoring, Motor Overcurrent Protection, Temperature Limit Control, Open-Collector Logic Level Translation, Loop Error Detection.
Industrial Sensor Threshold Detection
The LM393APS fits industrial sensor interfaces where a measured voltage must be converted into a switching decision. Each of its two channels can compare a sensor signal against an independently generated reference, and the open-collector output can drive a pulled-up digital input, relay, or optocoupler. Its dual differential inputs also allow the sensing point to be placed directly across the sensor rather than referred to a shared resistor network. Verify the input common-mode limits and offset voltage for the selected temperature range, and keep the comparator input traces short and away from motor-switching nodes. External filtering may be needed when the sensor signal changes quickly or contains noise near the switching threshold.
推薦
Battery Voltage Monitoring
A battery-management design can use the LM393APS to monitor a divided cell or pack voltage against a fixed reference. One channel detects an undervoltage condition while the other detects an overvoltage condition, giving the system two independent fault flags with open-collector outputs suitable for wired-AND wiring. Because the outputs do not actively source current, multiple monitored channels can share a pull-up when the design requires a combined alarm. The resistor divider should keep both inputs inside the device's specified common-mode range, and the threshold should include margin for comparator offset and temperature. This arrangement is useful where a simple fault signal is needed without the complexity of a dedicated fuel-gauge or protection controller.
推薦
Motor Overcurrent Protection
The LM393APS can supervise a motor or actuator drive by comparing a scaled current-sense voltage with a trip threshold. Its open-collector output can pull down a control signal, inhibit a gate driver, or operate a protection relay without requiring a push-pull output amplifier. The comparison is especially useful as an independent hardware backup to a controller performing software monitoring. Place the sense amplifier or divider close to the comparator to minimize pickup from motor switching noise, and use filtering that responds quickly enough to interrupt a fault but rejects brief transients. The absolute maximum and common-mode ratings must be checked for the highest voltage present during transient conditions, not only during steady-state operation.
推薦
Temperature Limit Control
A thermistor or resistive sensor network can be compared with a temperature-derived reference to produce an overtemperature or undertemperature signal. The LM393APS provides two channels for upper and lower limits, while the open-collector outputs can drive a cooling relay, fan, alarm input, or host-controller interrupt. Place the sensor and reference network near the comparator when the sensed temperature is spatially local, and route the outputs toward digital circuitry rather than long analog paths. Account for sensor tolerance, resistor accuracy, and comparator offset when defining the trip points. A positive feedback approach can also introduce controlled hysteresis, provided the added gain does not disturb the threshold accuracy.
推薦
Open-Collector Logic Level Translation
The LM393APS is useful when a low-voltage control signal must interface with a higher-voltage logic domain. Pull the open-collector output up to the higher rail, allowing the LM393 supply and inputs to remain in the lower-voltage domain while the receiving device sees the pulled-up logic level. This arrangement can also combine several comparator outputs into a wired-AND node because each output only pulls the shared line low. Validate the receiving device's input thresholds, the pull-up resistor's maximum current, and the output transistor's maximum sink current. Avoid continuously forcing the node low when it must support multiple active-low fault signals, and include adequate pull-up strength for the intended signal rise time.
推薦
Loop Error Detection
In a control or feedback system, one LM393APS channel can compare a feedback voltage with a command reference and assert an error output when the difference exceeds a permitted window. The second channel can monitor an independent condition, such as a power-good or saturation indicator. Open-collector outputs are convenient for driving an interrupt, alarm, or shutdown request because the device does not actively drive the bus high. Choose threshold tolerances that avoid nuisance trips from expected ripple and transient overshoot. The comparator should be located near the feedback source when possible, while its output route can extend to a controller because the pull-up defines the logic level locally.
推薦
推薦產品摘要
工程參考資料,適用於 LM393APS — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM393B | LM393LV | LM393AD | LM393BD | LM393 |
|---|---|---|---|---|---|---|
| Package | 8-pin small-outline package (SOP-8) | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Pull-Up Requirement | External pull-up required on each output | External pull-up required on each output | External pull-up required on each output | External pull-up required on each output | External pull-up required on each output | External pull-up required on each output |
主要差異化特點
- Wide single-supply operating range for general-purpose comparator designs (對比LM393LV)
- Two independent channels in a standard 8-pin surface-mount footprint (對比LM393)
- Open-collector outputs support wired-AND fault signaling and level translation (對比LM393B)
設計說明
Do not treat the open-collector output as a push-pull logic output. Each output must have an external pull-up resistor to establish a valid high level. Size the resistor to limit the output-transistor sink current while still meeting the receiving input's rise-time requirement, and verify the pull-up voltage against the absolute maximum ratings of every device connected to the output net.
Place each output pull-up resistor close to its corresponding LM393APS output pin and keep the connected net short to reduce propagation delay and susceptibility to injected noise. Route the differential input pair together and away from inductors, relay contacts, switching-node copper, and high-current return paths. Maintain a continuous ground reference beneath the device rather than relying on a fragmented ground plane.
Comparator inputs are high-impedance nodes and can capture switching noise if left physically long or adjacent to unrelated signals. Keep the sensing and reference components close to pins 2, 3, 5, and 6, use a compact ground return, and add only the filtering required to suppress identified noise. Excessive capacitance at an input can slow the comparison and should be checked against the required response time.
合規資訊
Compliance attributes are not stated in the manufacturer product information accessed for this record. The device is a general-purpose commercial comparator rather than an automotive-qualified option.