Texas Instruments

LM393APS - Dual 18V/36V Open-Collector Comparator | Texas Instruments

料号: LM393APS ✓ 量产中
18 V / 36 V Vdss 8-pin small-outline package (SOP-8) Package
最小起订量: 1 |

LM393APS 概述

The Texas Instruments LM393APS is a dual differential voltage comparator packaged in an 8-pin small-outline package for general-purpose signal comparison. It provides two independent comparator channels with open-collector outputs, rail-to-rail input capability, and operation across a single-supply range identified as 18V/36V in the LM393 series documentation. The LM393APS suffix denotes the surface-mount packaging option for the LM393AP family.

A comparator is an analog integrated circuit that evaluates the relative voltage applied to its inverting and non-inverting inputs. The LM393APS is therefore placed in the feedback path of control, sensing, or protection circuits rather than amplifying a signal directly. Its open-collector outputs can sink current from an external pull-up network, which allows wired logic interconnection, level translation, and relay-driver interfaces without requiring a dedicated push-pull output stage.

Key characteristics of this dual comparator include two independent channels, an open-collector output topology, rail-to-rail input handling, and an 8-pin surface-mount package. The open-collector arrangement also requires an external pull-up resistor when the output must reach a valid high logic level. The SOIC-8 footprint simplifies assembly on modern surface-mount boards while preserving the pin arrangement associated with the LM393AP family.

Internally, each LM393APS channel compares two input voltages and changes its output state according to their relationship. Because the outputs are open collector, the device can interface with TTL, CMOS, or other pull-up-defined logic rails when voltage and current limits are respected. The shared supply and ground pins make the two channels useful for window comparison, overvoltage detection, sensor thresholding, and complementary control decisions.

Typical uses include industrial sensor interfaces, battery and power-supply monitoring, temperature threshold circuits, motor or actuator control, loop-error detection, and general logic level conversion. Because the output transistor can remain off in the fault state, the open-collector structure is especially useful where a wired-AND behavior or fail-safe output is desirable.

When laying out a board, place the pull-up resistor close to the output net and route comparator inputs away from switching nodes and high-current traces. Confirm the absolute maximum supply voltage, input common-mode limits, output current, and propagation timing in the manufacturer datasheet before applying the device to a new design.

This page combines package identification, pin assignments, application guidance, comparison criteria, and design cautions to support faster component selection and PCB planning.

直接替换替代料: LM393APS ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: LM393APS (相同外形与封装尺寸) ——差异在于 Output Type, Package, Common-Mode Input Range, Comparator Type, Input Offset Voltage.

Texas Instruments
Output Type: Open-collector, rail-to-rail input capable
Package: SOIC-8 (D suffix)
Common-Mode Input Range: Includes ground (V-)
对比 LM393APS →
Texas Instruments
Output Type: Open collector
Package: 8-SOIC
Common-Mode Input Range: Includes ground
对比 LM393APS →
onsemi
Output Type: Open collector
Package: 8-SOIC
Common-Mode Input Range: Ground-level common-mode range in single-supply operation
对比 LM393APS →

LM393B

✅ 直接替换
📦 SOIC-8
Same LM393 dual open-collector architecture in an 8-pin SOIC footprint, with the B revision specified for improved performance including lower offset voltage and faster operation

📋 参考替代料(不在目录中)

LM393LV

✅ 直接替换
📦 SOIC-8
Same 8-pin SOIC dual-comparator footprint, but optimized for a lower voltage range with lower power, lower offset voltage, and faster speed than the original LM393

📋 参考替代料(不在目录中)

LM393AD

✅ 直接替换 ⚠️ 规格未核验
Texas Instruments
📦 SOIC-8
Dual differential comparator · 2 channels · Open collector · Includes ground · -38 V to +38 V · TTL, MOS, and CMOS · Commercial grade · 8-SOIC

联系询价

查看数据手册 →

LM393BD

✅ 直接替换 ⚠️ 规格未核验
📦 SOIC-8
Same 8-pin SOIC footprint and improved-performance B revision, with revised offset and speed characteristics relative to the original LM393 family

📋 参考替代料(不在目录中)

LM393

✅ 直接替换
Texas Instruments
📦 SOIC-8
2 (dual independent) · 2 V to 30 V · ±1 V to ±15 V · 2.0 mV (typical) · ±38 V · Includes ground (V-) · Open-collector, rail-to-rail input capable · TTL, MOS, CMOS (with external pull-up)

联系询价

查看数据手册 →

LM393APS 最大额定值与电气特性

Comparator Type Dual differential voltage comparator
Number of Channels 2 channels
电源电压 18 V / 36 V
输出类型 Open-collector
Input Common-Mode Range Rail-to-rail
封装 8-pin small-outline package (SOP-8)
安装类型 Surface mount
引脚数 8 pins
RoHS Compliance Unknown
REACH Compliance Unknown
Automotive AEC-Q100 Qualification Not applicable

LM393APS 引脚配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
引脚 1 OUT 1 — Open-collector output of comparator channel 1
引脚 2 IN 1- — Inverting input of comparator channel 1
引脚 3 IN 1+ — Non-inverting input of comparator channel 1
引脚 4 GND — Ground connection
引脚 5 IN 2+ — Non-inverting input of comparator channel 2
引脚 6 IN 2- — Inverting input of comparator channel 2
引脚 7 OUT 2 — Open-collector output of comparator channel 2
引脚 8 VCC — Positive supply connection

典型应用

LM393APS 适用于 6 应用s: Industrial Sensor Threshold Detection, Battery Voltage Monitoring, Motor Overcurrent Protection, Temperature Limit Control, Open-Collector Logic Level Translation, Loop Error Detection.

🏭

Industrial Sensor Threshold Detection

The LM393APS fits industrial sensor interfaces where a measured voltage must be converted into a switching decision. Each of its two channels can compare a sensor signal against an independently generated reference, and the open-collector output can drive a pulled-up digital input, relay, or optocoupler. Its dual differential inputs also allow the sensing point to be placed directly across the sensor rather than referred to a shared resistor network. Verify the input common-mode limits and offset voltage for the selected temperature range, and keep the comparator input traces short and away from motor-switching nodes. External filtering may be needed when the sensor signal changes quickly or contains noise near the switching threshold.

⚡

Battery Voltage Monitoring

A battery-management design can use the LM393APS to monitor a divided cell or pack voltage against a fixed reference. One channel detects an undervoltage condition while the other detects an overvoltage condition, giving the system two independent fault flags with open-collector outputs suitable for wired-AND wiring. Because the outputs do not actively source current, multiple monitored channels can share a pull-up when the design requires a combined alarm. The resistor divider should keep both inputs inside the device's specified common-mode range, and the threshold should include margin for comparator offset and temperature. This arrangement is useful where a simple fault signal is needed without the complexity of a dedicated fuel-gauge or protection controller.

🏭

Motor Overcurrent Protection

The LM393APS can supervise a motor or actuator drive by comparing a scaled current-sense voltage with a trip threshold. Its open-collector output can pull down a control signal, inhibit a gate driver, or operate a protection relay without requiring a push-pull output amplifier. The comparison is especially useful as an independent hardware backup to a controller performing software monitoring. Place the sense amplifier or divider close to the comparator to minimize pickup from motor switching noise, and use filtering that responds quickly enough to interrupt a fault but rejects brief transients. The absolute maximum and common-mode ratings must be checked for the highest voltage present during transient conditions, not only during steady-state operation.

🌡️

Temperature Limit Control

A thermistor or resistive sensor network can be compared with a temperature-derived reference to produce an overtemperature or undertemperature signal. The LM393APS provides two channels for upper and lower limits, while the open-collector outputs can drive a cooling relay, fan, alarm input, or host-controller interrupt. Place the sensor and reference network near the comparator when the sensed temperature is spatially local, and route the outputs toward digital circuitry rather than long analog paths. Account for sensor tolerance, resistor accuracy, and comparator offset when defining the trip points. A positive feedback approach can also introduce controlled hysteresis, provided the added gain does not disturb the threshold accuracy.

🔧

Open-Collector Logic Level Translation

The LM393APS is useful when a low-voltage control signal must interface with a higher-voltage logic domain. Pull the open-collector output up to the higher rail, allowing the LM393 supply and inputs to remain in the lower-voltage domain while the receiving device sees the pulled-up logic level. This arrangement can also combine several comparator outputs into a wired-AND node because each output only pulls the shared line low. Validate the receiving device's input thresholds, the pull-up resistor's maximum current, and the output transistor's maximum sink current. Avoid continuously forcing the node low when it must support multiple active-low fault signals, and include adequate pull-up strength for the intended signal rise time.

📡

Loop Error Detection

In a control or feedback system, one LM393APS channel can compare a feedback voltage with a command reference and assert an error output when the difference exceeds a permitted window. The second channel can monitor an independent condition, such as a power-good or saturation indicator. Open-collector outputs are convenient for driving an interrupt, alarm, or shutdown request because the device does not actively drive the bus high. Choose threshold tolerances that avoid nuisance trips from expected ripple and transient overshoot. The comparator should be located near the feedback source when possible, while its output route can extend to a controller because the pull-up defines the logic level locally.

What is the LM393APS?
The LM393APS is a Texas Instruments dual differential voltage comparator in an 8-pin surface-mount package. It contains two independent comparator channels with open-collector outputs and rail-to-rail inputs. According to the manufacturer datasheet, the LM393 family is intended for general-purpose comparison over a 2 V to 36 V supply range, making it useful for threshold detection, control loops, and sensing circuits.
Where can I download the LM393APS datasheet PDF?
The official Texas Instruments LM393 datasheet is available at https://www.ti.com/lit/ds/symlink/lm393.pdf. The document defines the LM393APS device, its electrical limits, pin functions, and recommended operating conditions. It also distinguishes the surface-mount LM393APS option from other LM393 package and temperature variants listed in the ordering information.
Where can I find the LM393APS pinout?
The LM393APS uses the standard 8-pin SOIC comparator arrangement: pin 1 is output 1, pins 2 and 3 are the inverting and non-inverting inputs of channel 1, pin 4 is ground, pins 5 and 6 are the non-inverting and inverting inputs of channel 2, pin 7 is output 2, and pin 8 is the supply input. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.
Does the LM393APS need a pull-up resistor?
Yes, the LM393APS requires an external pull-up resistor on each open-collector output. The output transistor actively pulls the node toward ground but cannot source current, so the resistor establishes the high state. Place the resistor close to the output pin and size it for the pull-up voltage, the required logic rise time, and the output leakage current.
What is the difference between LM393APS and LM393AP?
The LM393APS and LM393AP belong to the same Texas Instruments dual-comparator family, but their package mounting differs. LM393APS is the surface-mount option in an 8-pin small-outline package, while LM393AP is the through-hole 8-pin DIP option identified in the DigiKey listing. Confirm the footprint and pin dimensions before transferring a design between the two package variants.
Is LM393APS the same as LM393B?
The LM393APS and LM393B are related members of the LM393 family, but they are not automatically identical in every rating. Texas Instruments identifies LM393B as an alternate part with improved performance, including lower offset voltage and faster operation. For a drop-in decision, compare the supply, input common-mode, output current, timing, and temperature limits for the exact ordering codes.
What can replace the LM393APS?
A drop-in replacement for the LM393APS must use the same 8-pin SOIC footprint, preserve the LM393 pin arrangement, and retain the open-collector output behavior. The LM393B and LM393LV options are relevant same-family candidates, while an LM393 from another manufacturer may also fit if its pinout and electrical limits match. Verify the complete ordering table before releasing a substitute into production.
Where can I buy the LM393APS online?
Use the Request a Quote form on this page to request the current LM393APS unit price, stock status, minimum order quantity, and lead time. The form supports direct purchasing coordination without relying on static prices. Confirm the requested package code is LM393APS rather than LM393AP, LM393B, or another member of the comparator family.
How much does the LM393APS cost?
Current LM393APS pricing is best obtained through the Request a Quote form on this page because component prices and stock levels change with market conditions. Submit the quantity, target date, and required package or shipment details with the request. The form also lets you ask about broken-box quantities and scheduled delivery for production planning.
What is the lead time for LM393APS?
The current lead time depends on manufacturer inventory, distributor allocation, and the quantity requested. Submit an LM393APS request through the Request a Quote form on this page and state the required delivery schedule. For production planning, request the manufacturer lifecycle status, dated lot availability, and any change-notification information along with the quotation.
Is the LM393APS suitable for a 5V control circuit?
The LM393APS is a single-supply comparator whose family is specified for operation from 2 V to 36 V, so it can be used in a 5 V control circuit. The open-collector output still needs an appropriate pull-up. According to the manufacturer datasheet, the supply must remain within the absolute maximum rating even when one input is driven slightly outside the supply rail.
When should I choose the LM393APS over a modern comparator?
Choose the LM393APS when you need two inexpensive, independent general-purpose channels, a wide single-supply operating range, and an open-collector output that can be pulled up to a system logic level. A modern push-pull comparator may be preferable when very fast propagation, rail-to-rail output swing, or a low-power shutdown function dominates the design. The application should tolerate the LM393 family response speed.
Can the two LM393APS channels be used together for window comparison?
The two independent LM393APS channels can implement a window comparison by connecting one input to the upper threshold and the other to the lower threshold, then using their open-collector outputs with pull-up resistors. This arrangement indicates whether the measured voltage lies inside or outside a defined band. Account for each channel's offset and the effect of the shared supply in the threshold design.
What are the key specifications of LM393APS engineers should know?
The LM393APS is a dual, general-purpose differential comparator with two open-collector outputs, rail-to-rail inputs, and an 8-pin surface-mount package. The LM393 series supports a single supply identified as 2 V to 36 V. These characteristics determine its suitability for threshold detection, logic interfacing, sensor conditioning, and protection functions, while the open-collector topology requires external pull-up resistors.
What is the best ON Semiconductor equivalent for the LM393APS?
An ON Semiconductor LM393 in the matching 8-pin surface-mount package is a candidate equivalent because the LM393APS specification comparison identifies both devices as SOP-8 dual comparators. A cross-brand substitution still requires confirmation of pinout, supply rating, common-mode range, output sink current, temperature range, and offset-voltage limits. Do not treat the family name alone as proof of drop-in compatibility.

工程参考数据: LM393APS ——对比、设计指导和合规信息。

选型指南

Choose the LM393APS when the design needs two inexpensive, independent general-purpose comparator channels, a wide single-supply range, and open-collector outputs that can sink current or share a wired-AND bus. It is particularly suitable for industrial threshold detection, battery supervision, thermal limits, and simple fault monitoring where a pull-up resistor is acceptable. Select LM393B when the same footprint and topology are needed but lower offset voltage or faster operation improves the result. Select LM393LV for low-voltage systems where lower power, lower offset, and faster speed are the primary priorities. Consider the cross-brand LM393 only after checking its exact pinout, common-mode limits, sink current, timing, and temperature ratings against the Texas Instruments device. In every case, verify the output pull-up voltage, absolute maximum limits, and whether the required response speed is sufficient for the application.

与替代料对比

参数 本产品 LM393B LM393LV LM393AD LM393BD LM393
Package 8-pin small-outline package (SOP-8) SOIC-8 SOIC-8 SOIC-8 SOIC-8 SOIC-8
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments onsemi
Comparator Configuration Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator
Output Type Open-collector Open-collector Open-collector Open-collector Open-collector Open-collector
Number of Channels 2 2 2 2 2 2
Pull-Up Requirement External pull-up required on each output External pull-up required on each output External pull-up required on each output External pull-up required on each output External pull-up required on each output External pull-up required on each output

关键差异点

  • Wide single-supply operating range for general-purpose comparator designs (对比 LM393LV)
  • Two independent channels in a standard 8-pin surface-mount footprint (对比 LM393)
  • Open-collector outputs support wired-AND fault signaling and level translation (对比 LM393B)

设计说明

Do not treat the open-collector output as a push-pull logic output. Each output must have an external pull-up resistor to establish a valid high level. Size the resistor to limit the output-transistor sink current while still meeting the receiving input's rise-time requirement, and verify the pull-up voltage against the absolute maximum ratings of every device connected to the output net.

Place each output pull-up resistor close to its corresponding LM393APS output pin and keep the connected net short to reduce propagation delay and susceptibility to injected noise. Route the differential input pair together and away from inductors, relay contacts, switching-node copper, and high-current return paths. Maintain a continuous ground reference beneath the device rather than relying on a fragmented ground plane.

Comparator inputs are high-impedance nodes and can capture switching noise if left physically long or adjacent to unrelated signals. Keep the sensing and reference components close to pins 2, 3, 5, and 6, use a compact ground return, and add only the filtering required to suppress identified noise. Excessive capacitance at an input can slow the comparison and should be checked against the required response time.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

Compliance attributes are not stated in the manufacturer product information accessed for this record. The device is a general-purpose commercial comparator rather than an automotive-qualified option.

数据核验日期: 2026-11-13 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

lm393ap datasheet LM393APS datasheet LM393APS datasheet pdf LM393APS pinout Texas Instruments LM393APS LM393APS SOIC-8 footprint LM393APS open collector output LM393APS vs LM393B LM393APS equivalent LM393APS drop-in replacement LM393APS voltage comparator application LM393APS price LM393APS stock LM393APS pull-up resistor LM393APS industrial sensor threshold

相关元器件 & 术语

Texas Instruments LM393APS LM393AP LM393B LM393LV LM393 LM393AD LM393BD onsemi dual differential comparator voltage comparator analog integrated circuit open-collector output rail-to-rail input external pull-up resistor SOIC-8 surface mount SMD industrial sensor interface battery voltage monitoring motor overcurrent protection temperature limit control logic level translation loop error detection RoHS
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情