LM393LVQDRQ1 - Dual Open-Drain Comparator | Texas Instruments
MPN: LM393LVQDRQ1 ✓ 啟用中LM393LVQDRQ1 概覽
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM393LV-Q1 family belongs to the comparator hierarchy within interface and signal-conditioning semiconductors. Unlike an operational amplifier intended primarily for linear amplification, this comparator is optimized for threshold detection, fault signaling, and logic-level translation. Its two channels operate independently, allowing one package to monitor two unrelated signals.
The open-drain output architecture is a defining electrical feature. Each output transistor can pull its output low, but it does not actively drive the output high; an external pull-up resistor supplies the high state. This arrangement permits the output voltage to match a system logic rail and allows multiple open-drain outputs to share a bus when their operating conditions permit. It is especially useful in wired-AND style signaling, battery-powered sensing, and systems that require an external pull-up for interface compatibility.
The maximum 5 mV input offset voltage and typical 5 nA input bias current support accurate threshold decisions with relatively little input imbalance or source-current error. The low-voltage operating range is appropriate for sensors, portable equipment, battery-powered controllers, and mixed-signal circuits using modern low-energy logic levels. Automotive qualification adds value where a wide operating-temperature range and controlled device quality are important, although the application must still satisfy all electrical limits.
Typical uses include battery-voltage monitoring, sensor-threshold detection, overvoltage and undervoltage protection, window comparators, and translating analog sensor signals into open-drain logic events. Two independent channels can also implement separate positive and negative thresholds, or monitor two rails in a compact control board. Because the output is open drain, the system designer must include a pull-up resistor and account for its load current, rise time, and bus capacitance.
Design the input network so that signals remain within the comparator's common-mode input range, and account for the 5 mV maximum offset when defining switching thresholds. Place the pull-up resistor close to the output when fast edges and low susceptibility to interference are required. Validate the complete trace, pull-up value, and attached load rather than evaluating only the unloaded comparator output.
This product page combines manufacturer device information, package-specific pin information, application engineering guidance, and clearly scoped replacement analysis. The comparison and selection sections emphasize electrical compatibility, qualification differences, and the design consequences of using an open-drain output rather than a push-pull output.
直接替換替代品,適用於 LM393LVQDRQ1 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM393LVQDRQ1 (相同外形與佔位) — 差異在於 Comparator Type, Operating Temperature Range, Output Type, Package.
LM393LVQDR
✅ 直接替換📋 參考替代品(不在目錄中)
LM393LVDR
✅ 直接替換聯絡詢價
查看資料表 →LMV393DR
✅ 直接替換📋 參考替代品(不在目錄中)
LM393LVQDRQ1 最大額定值與電氣特性
| Comparator Type | Dual, general-purpose voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 1.65 V to 5.5 V |
| 輸出類型 | Open-drain |
| Input Offset Voltage | 5 mV maximum |
| Input Bias Current | 5 nA typical |
| 工作溫度範圍 | -40 °C to 125 °C |
| 封裝 | 8-SOIC, 4.5 mm width |
| 腳位數 | 8 pins |
| 安裝類型 | Surface mount |
| Automotive Qualification | Qualified automotive comparator |
LM393LVQDRQ1 腳位配置
| 腳位 1 | 1OUT — Comparator 1 open-drain output |
| 腳位 2 | 1IN− — Comparator 1 inverting input |
| 腳位 3 | 1IN+ — Comparator 1 noninverting input |
| 腳位 4 | GND — Ground connection |
| 腳位 5 | 2IN+ — Comparator 2 noninverting input |
| 腳位 6 | 2IN− — Comparator 2 inverting input |
| 腳位 7 | 2OUT — Comparator 2 open-drain output |
| 腳位 8 | VCC — Positive supply connection |
典型應用
LM393LVQDRQ1 適用於 6 應用s: Battery Voltage Monitoring, Sensor Threshold Detection, Automotive Power-Fault Signaling, Overvoltage and Undervoltage Protection, Window Comparator, Low-Voltage Logic Interface.
Battery Voltage Monitoring
The LM393LVQDRQ1 fits low-energy battery systems because its 1.65 V to 5.5 V supply range supports operation as the battery voltage approaches its lower operating region. The 5 mV maximum input offset voltage provides a defined accuracy limit when the device detects a critical battery threshold, while the open-drain output can directly pull an enable, warning, or power-path-control signal low. Use a resistor divider to scale the battery voltage into the input range, add an external pull-up on the output, and test threshold behavior across the intended battery temperature range.
推薦
Sensor Threshold Detection
The LM393LVQDRQ1 is suitable for detecting a sensor signal crossing a defined threshold in a compact embedded system. Its dual-channel architecture allows two related sensors or two thresholds to be monitored without duplicating the comparator package. The typical 5 nA input bias current limits input-loading impact in high-impedance sensor networks, and the 5 mV maximum offset defines the threshold uncertainty that must be included in the design margin. Place the resistor network close to the device and use the open-drain output with a defined pull-up voltage.
推薦
Automotive Power-Fault Signaling
The LM393LVQDRQ1 supports automotive power-fault monitoring because it combines a 1.65 V to 5.5 V operating range with a -40 °C to 125 °C temperature specification and Q1 family identification. Its open-drain output can participate in a low-side wired-AND fault bus, allowing multiple monitoring channels to indicate a fault without driving conflicting high states. The design must include a pull-up, logic-level compatibility checks, transient protection, and qualification review of all associated components. The comparator itself does not replace overvoltage or reverse-polarity protection stages.
推薦
Overvoltage and Undervoltage Protection
The LM393LVQDRQ1 can supervise a low-voltage power rail by comparing the divided rail voltage against a reference and generating an open-drain fault event. Two independent channels can implement separate upper and lower limits, which is useful in battery systems where both over-discharge and overcharge conditions require action. Use suitably precise divider resistors, allow for the 5 mV maximum offset, and choose a pull-up that remains compatible with the downstream logic. Testing must include line transients and the full temperature range rather than only nominal room-temperature conditions.
推薦
Window Comparator
The two independent LM393LVQDRQ1 channels can be connected to implement a voltage window comparator, with one channel detecting the lower limit and the other detecting the upper limit. Open-drain outputs allow the two channels to share a pull-up when the desired result is a fault indication asserted only when either limit is crossed. The 1.65 V minimum supply voltage is useful in compact low-voltage systems, while the 5 mV maximum offset must be considered at both boundaries. Verify logic truth states carefully because tying open-drain outputs together requires compatible device behavior.
推薦
Low-Voltage Logic Interface
The LM393LVQDRQ1 can translate a low-voltage analog decision into an open-drain logic signal for a microcontroller, sensor hub, or mixed-signal controller. Because the output does not actively drive high, the external pull-up determines the high voltage and permits compatibility with a higher-voltage digital domain while the comparator operates from 1.65 V to 5.5 V. Keep the pull-up short to control rise time, account for output capacitance when selecting its resistance, and ensure that every attached signal remains within the comparator's common-mode input range.
推薦
推薦產品摘要
工程參考資料,適用於 LM393LVQDRQ1 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM393LVQDR | LM393LVDR | LMV393DR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC, 4.5 mm width | 8-SOIC, 4.5 mm width | 8-SOIC | 8-SOIC |
| Comparator Configuration | Dual, independent channels | Dual, independent channels | Dual, independent channels | Dual comparator |
| Supply Voltage Range | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 2.7 V to 5.5 V |
| Output Type | Open-drain | Open-drain | Open-drain | Open-drain |
主要差異化特點
- Lower minimum supply voltage within the same TI low-voltage family (對比LMV393DR)
- Automotive Q1 family identification (對比LM393LVQDR)
- Dual independent open-drain channels in one package (對比TL331LV-Q1)
設計說明
Do not treat an open-drain output as a push-pull logic output. The transistor actively pulls the output low but does not actively drive it high, so every output node requires a pull-up resistor unless another compatible open-drain device supplies the high state. Select the pull-up voltage for the downstream logic domain and check its current at the lowest output voltage. Misconnecting or omitting the pull-up can leave the output floating and produce undefined system behavior.
Account for the maximum 5 mV input offset voltage when defining a switching threshold, especially for battery or sensor monitoring where the measured value changes slowly. The 1.65 V to 5.5 V supply range does not by itself guarantee that every input is valid at every supply voltage. Verify both the input common-mode limits and output-level behavior from the manufacturer electrical-characteristics table. Add hysteresis where noise near the threshold could otherwise cause repeated output transitions.
Place the input divider and optional feedback resistors close to the relevant comparator pins to minimize coupling from adjacent switching nodes. Keep the open-drain output and pull-up resistor compact because long traces increase capacitance and slow the rising edge. Maintain a direct ground return for pin 4, and avoid routing sensitive input traces beside power inductors, motor-switching nodes, or high-current return paths. Confirm the final two-layer or multilayer layout against the manufacturer's application guidance.
合規資訊
Texas Instruments identifies LM393LVQDRQ1 as an automotive Q1 low-voltage comparator. Detailed RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed in the current manufacturer product documentation.