LM393TL/NOPB - Dual Open-Collector Comparator, 8-DSBGA | Texas Instruments
MPN: LM393TL/NOPB ✓ 啟用中LM393TL/NOPB 概覽
A comparator is a differential amplifier whose output indicates which of two input voltages is higher. A voltage comparator belongs to the amplifier IC family, sits below the broader analog IC grouping, and ultimately falls under the semiconductor hierarchy. Because a comparator output is digital in nature while its inputs are analog, comparators bridge the analog and digital domains and are widely used for thresholding, level detection, sensor conditioning and open-drain bus arbitration.
The LM393-N series places two independent precision comparators on one die, each with its own differential input pair and open-collector output. Key features include a low offset voltage, low supply current, a wide common-mode input voltage range that includes ground, and an output stage compatible with CMOS, DTL, ECL, MOS and TTL logic families. Because the outputs are open collector, the output high level is set by an external pull-up resistor, allowing wired-AND busing and level shifting to any supply rail.
Internally, each channel uses a differential input stage with a precision trim and a broadband output stage designed for moderate propagation delay. This architecture trades speed for very low supply current, which is exactly what makes the LM393 family popular in battery-powered and always-on monitoring circuits. The 8-DSBGA package places the device in a thin, compact footprint of only 8 large (12 mil) bumps, which is ideal for space-constrained handheld and portable equipment where a dual comparator saves both board area and part count.
Typical applications include window comparators for battery monitoring, over/undervoltage protection, temperature threshold detection with thermistors, zero-cross detection in AC mains circuits, sorting and level shifting, and general-purpose dual-rail sensing in consumer and industrial equipment. Each channel can be used independently, so one half may act as a comparator while the other provides an independent reference or supervisory function.
When designing around the LM393TL/NOPB, remember that the open-collector output requires an external pull-up resistor, typically 2 kΩ to 10 kΩ, and that input common-mode range and output saturation levels depend on the supply voltage. Because the DSBGA package has no large thermal pad, keep instantaneous dissipation low and maintain adequate board area for heat spreading.
This page consolidates manufacturer specifications, drop-in alternatives, a parameter-by-parameter comparison table, and practical PCB and application guidance that are not assembled in one place on the manufacturer datasheet, helping engineers qualify the LM393TL/NOPB for portable sensing, protection and interface designs.
直接替換替代品,適用於 LM393TL/NOPB — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM393TL/NOPB (相同外形與佔位) — 差異在於 Output Type, Package, Input Offset Voltage.
LM393TLX/NOPB
✅ 直接替換聯絡詢價
查看資料表 →LM393DT
✅ 直接替換✓ 有庫存
$0.0461 / 單位
查看資料表 →LM393B
✅ 直接替換📋 參考替代品(不在目錄中)
LM393LV
✅ 直接替換📋 參考替代品(不在目錄中)
LMV393
✅ 直接替換📋 參考替代品(不在目錄中)
LM393TL/NOPB 最大額定值與電氣特性
| Device Type | Dual differential voltage comparator |
| Number of Channels | 2 |
| Supply Voltage Range (Single) | 2 V to 36 V |
| Supply Voltage Range (Dual) | +/-1 V to +/-18 V |
| 輸出類型 | Open-Collector (CMOS, DTL, ECL, MOS, TTL compatible) |
| Input Offset Voltage | 2.0 mV max |
| Common-Mode Input Range | Includes ground (rail-to-rail input) |
| 封裝 | 8-DSBGA (8 large 12 mil bumps), thin |
| Number of Pins / Balls | 8 |
| 安裝類型 | Surface Mount |
| Grade | Commercial |
| Product Family | LM193 / LM2903 / LM393 series |
| Output Pull-Up Requirement | External pull-up resistor required (open collector) |
LM393TL/NOPB 8-dsbga (8 large 12 mil bumps), thin 腳位配置指南
LM393TL/NOPB(8-dsbga (8 large 12 mil bumps), thin 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM393TL/NOPB.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM393TL/NOPB 適用於 6 應用s: Battery Undervoltage and Overvoltage Detection, Over/Undervoltage Protection and Power Sequencing, Temperature Threshold Sensing with Thermistors, Portable and Wearable Sensor Interfaces, Zero-Cross and AC Sensing Circuits, Consumer and Industrial Equipment Level Shifting.
Battery Undervoltage and Overvoltage Detection
The LM393TL/NOPB suits single-cell and multi-cell battery supervision because its 2 V to 36 V single-supply range lets one device monitor a pack directly, and its common-mode input range includes ground so a resistive divider to the cell terminal can be compared directly against a precision reference. The 2.0 mV max input offset keeps the trip point error small relative to typical Li-ion cell spacing of a few hundred millivolts. Each of the two independent channels can implement the overvoltage and undervoltage thresholds, and because both outputs are open collector they can share one pull-up resistor to produce a single combined fault flag, eliminating a separate logic gate.
推薦
Over/Undervoltage Protection and Power Sequencing
Protecting downstream loads from out-of-range rails is a classic dual-comparator job, and the LM393TL/NOPB performs both thresholds in one 8-DSBGA package. One channel watches the rail high side and the other the low side, with the reference divider sized for the tolerance needed. The open-collector outputs can pull down a shared reset or power-good node directly, which is simpler and lower power than driving a rail actively. With a 2.0 mV max input offset the sensing error is negligible next to typical protection window tolerances, so no trimming is required in most designs.
推薦
Temperature Threshold Sensing with Thermistors
The low offset voltage of the LM393TL/NOPB makes it effective for thermistor-based thermal monitoring, where the thermistor divider sits at a few volts and the detection band can be only tens of millivolts wide. Two channels allow separate high-temperature and low-temperature alarm points with independently chosen dividers. Because the comparator input common-mode range extends to ground, one channel can monitor a cold-junction or ambient sensor near 0 V without a level shift. Open-collector outputs also let the alarms be wired-AND into a single interrupt line, freeing a microcontroller pin and reducing interrupt handling complexity.
推薦
Portable and Wearable Sensor Interfaces
In handheld and wearable products the 8-DSBGA package of the LM393TL/NOPB is a significant space advantage over an SOIC-8 dual comparator, saving roughly half the footprint area while still providing two channels. The family was designed for single-supply operation over a wide range of voltages, so a 3.3 V or 1.8 V system can run the comparator straight from the main rail rather than requiring a boosted supply. The thin DSBGA outline also keeps the stack-up shallow, which suits wearables where board-to-case clearance is tight. Care is needed at assembly because the 8 large bumps still demand fine-pitch placement capability.
推薦
Zero-Cross and AC Sensing Circuits
The LM393TL/NOPB is routinely used for zero-cross detection and AC sensing because its wide supply tolerance and low offset allow a scaled AC waveform to be compared against ground with minimal distortion of the zero-cross point. The open-collector output drives a pull-up, and the resulting pulse train is convenient for driving a timer input or an optocoupler LED stage. Because the device accepts dual supplies of +/-1 V to +/-18 V, it can also be biased directly on a +/-12 V mains-derived sensing node, removing the need for a separate level shifter. The same technique is applied in motor control and dimming circuits.
推薦
Consumer and Industrial Equipment Level Shifting
When a sensor or logic domain runs at a different voltage than the host controller, the LM393TL/NOPB open-collector output provides a simple, low-power level shifter: pull the output up to the destination supply and the comparator sinks current from the higher-voltage domain. The outputs are compatible with CMOS, DTL, ECL, MOS and TTL logic families, so the same part works across mixed vintage logic. Two channels in one 8-DSBGA package reduce part count in equipment where several lines need translation, which helps both BOM cost and PCB density in industrial control panels and consumer set-top devices.
推薦
推薦產品摘要
工程參考資料,適用於 LM393TL/NOPB — 比較、設計指引及合規資訊。
選型指南
Select LM393TLX/NOPB instead when the same 8-DSBGA part is needed in tape-and-reel format for volume assembly - the electrical behaviour is identical and only the packing changes. Choose LM393LV when you work only below roughly 16 V and want the lower-voltage family option, accepting reduced flexibility for bipolar sensing. Choose LMV393 when supply current dominates the design, for example in battery-powered wearables, since the CMOS implementation draws roughly twenty times less current, but verify that the CMOS input common-mode range and output levels suit your node.
For most new designs that do not need the sub-1 cm-squared footprint, an SOIC-8 or SOT-23-5 dual comparator is easier to assemble and source in volume; the LM393TL/NOPB earns its place when area, not assembly convenience, is the binding constraint.
與替代品比較
| 參數 | 本產品 | LM393TLX/NOPB | LM393 | LM393B | LM393LV | LMV393 |
|---|---|---|---|---|---|---|
| Package | 8-DSBGA (8 large 12 mil bumps) | 8-DSBGA (8 large 12 mil bumps) - same | 8-DSBGA thin BGA option - same | 8-DSBGA (family option) - same | 8-DSBGA (family option) - same | 8-DSBGA (family option) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Voltage Range | 2 V to 36 V (single), +/-1 V to +/-18 V (dual) | 2 V to 36 V (single) | 2 V to 36 V (single) | 2 V to 36 V (single) | Lower-voltage family option | 2.7 V to 16 V |
| Output Type | Open-Collector (CMOS, DTL, ECL, MOS, TTL compatible) | Open-Collector | Open-Collector | Open-Collector | Open-Collector family architecture | Open-Drain CMOS |
主要差異化特點
- Two independent channels in a compact 8-DSBGA footprint (對比LM393TLX/NOPB)
- Wider supply ceiling than CMOS dual comparators (對比LMV393)
- Lower offset and dual-supply flexibility versus low-voltage family options (對比LM393LV)
- Single-supply design intent across a very wide voltage range (對比LM393)
設計說明
The single most common mistake with the LM393TL/NOPB is forgetting the external pull-up resistor on the open-collector output. Without it the output node floats and the comparator appears to malfunction. Select a pull-up between roughly 2 kOhm and 10 kOhm, or larger for slower, lower-power switching. A second common trap is driving an LED or relay directly from the output: because the stage only sinks current, use the device to sink through the load to ground and pull the load up to the supply, and check the sink current against the output rating.
The 8-DSBGA package has 8 large 12 mil bumps with no exposed thermal pad, so thermal relief is limited to the bump footprint and thin board copper. Keep copper pour and thermal vias minimal but present under and around the package to spread the small dissipation of a comparator, and keep the layout compact so the low-capacitance inputs are not routed over noisy switching nodes. Provide a solid ground reference plane directly under the device so the common-mode performance and offset behaviour of both channels are not degraded by ground bounce.
Route the inverting and non-inverting inputs of each channel as a tight, closely-coupled pair to minimize pickup of differential noise, since the whole benefit of the 2.0 mV max offset specification is lost if the comparator is comparing two noisy, uncorrelated signals. Keep these nets away from switching node inductors, relay contacts and high-current return paths. Where the sensed signal is high impedance, add a small guard ring or driven shield around the input pad and keep the pull-up resistor on the output physically remote from the input pins.
Estimated: with a 12 V supply, a 5 V output pull-up and a 10 mA sink on one channel, the output transistor dissipates roughly (12 V - 5 V) x 10 mA = 70 mW. While this is small, the total dissipation of both channels plus bias current still sets the die temperature inside the thin DSBGA package, which has no dedicated heat path. Estimated: at 70 mW per channel and 2 channels the junction rise stays well within limits for a 1 oz copper DSBGA land pattern, but verify against the ambient temperature limit of your grade before using this estimate in a safety margin calculation.
合規資訊
LM393TL/NOPB is a commercial-grade part on the Texas Instruments LM393-N family page. The NOPB suffix denotes a lead-free finish in the TI ordering code system, but RoHS, REACH and halogen-free declarations are not reproduced in the manufacturer material available for this listing, so they are recorded as unknown rather than assumed. AEC-Q100 does not apply to this commercial-grade device.