LMR981G-GTR - Low-Power Rail-to-Rail Op Amp | ROHM
MPN: LMR981G-GTR ✓ 啟用中LMR981G-GTR 概覽
An operational amplifier, or op amp, is an analog integrated circuit that provides high voltage gain in an open-loop configuration. Rail-to-rail input and output amplifiers can accept input signals close to the negative and positive supply rails and can swing their output close to those rails. This capability is useful in low-voltage systems because it expands the usable input and output range without requiring a separate midrail bias reference.
The LMR981G belongs to the ROHM LMR series of low-power input-output full-swing operational amplifiers. According to the manufacturer product page, this series was developed for single, dual, and quad amplifier configurations that operate at low voltage and low supply current. The LMR981G is the single-amplifier configuration, while the LMR982 family adds a shutdown function. Its 5 V supply rating, 6-pin SSOP package, and rail-to-rail input/output architecture make it a compact choice for portable and embedded analog designs.
Key electrical characteristics include one amplifier circuit per package, general-purpose signal conditioning, low-power operation, and full-swing input and output behavior. The datasheet defines the detailed input bias current, input offset voltage, unity-gain bandwidth, slew rate, noise specifications, and output-current limits for design calculations. Because this page does not reproduce those numeric ratings, engineers should use the manufacturer datasheet for precision AC and DC design work.
Typical applications include conditioning the output of resistive sensors, buffering ADC inputs, implementing active filters, and amplifying low-level analog waveforms from portable instruments. The SSOP-6 package is also useful where board space is restricted, although its small body and limited copper area require attention to thermal rise when the amplifier operates continuously near its output-current limit.
When designing around the LMR981G-GTR, confirm the exact input common-mode range, output swing, unity-gain bandwidth, and noise figures for the selected supply voltage. Place the bypass capacitor close to the supply pin, keep feedback resistors close to the amplifier inputs, and avoid driving a capacitive load directly unless the stability behavior has been verified.
This page combines the manufacturer product information with a practical selection guide, packaging details, design cautions, and a structured comparison of drop-in candidates. It adds engineering context around the LMR981G-GTR without replacing the manufacturer datasheet for guaranteed limits, test conditions, and absolute maximum ratings.
直接替換替代品,適用於 LMR981G-GTR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
LMR981G
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LMR982G-GTR
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LMR981G-GTR 最大額定值與電氣特性
| Amplifier Type | General-purpose operational amplifier |
| Number of Circuits | 1 circuit |
| Input Type | Rail-to-rail input |
| 輸出類型 | Rail-to-rail output |
| 供應電壓 | 5 V maximum specified supply |
| Low-Voltage Operation | Supported |
| Low Supply Current | Yes |
| Shutdown Function | Not included in LMR981G; shutdown is applied to LMR982 |
| 封裝 | 6-pin SSOP, embossed tape-and-reel |
| 安裝類型 | Surface mount |
| Product Series | ROHM LMR series, low-power input-output full-swing operational amplifier |
LMR981G-GTR 6-pin ssop, embossed tape-and-reel 腳位配置指南
LMR981G-GTR(6-pin ssop, embossed tape-and-reel 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LMR981G-GTR.
請參閱 資料表 以查看完整腳位配置。
典型應用
LMR981G-GTR 適用於 6 應用s: Low-Voltage Sensor Signal Conditioning, Portable Audio Preamp and Buffer, Active Low-Pass Filter, ADC Input Buffer and Driver, Battery-Powered Measurement Module, Industrial Control Signal Interface.
Low-Voltage Sensor Signal Conditioning
The LMR981G-GTR suits sensor front ends that operate from a low supply and produce signals near either rail. Its rail-to-rail input behavior reduces the need for a midrail reference when the sensor output spans much of the supply range, while the single amplifier and 6-pin SSOP package conserve board area. Place the amplifier close to the sensor to minimize leakage through PCB contamination and long traces. For resistive dividers or thermistors, verify input bias current against the source impedance and confirm offset and noise in the datasheet. The low-power operating approach is especially useful in battery-powered monitors where the amplifier must remain active continuously.
推薦
Portable Audio Preamp and Buffer
The LMR981G-GTR can buffer a microphone, line-level input, or headphone-driver stage in a single-supply audio design. Rail-to-rail output allows the signal to use more of the available supply range, which is valuable in compact portable equipment. Configure the non-inverting gain path with feedback resistors placed close to the amplifier pins, and place input filtering ahead of the amplifier to avoid amplifying unwanted high-frequency content. Because audio quality depends on noise, distortion, and stability, confirm the applicable gain-bandwidth, output-swing, and capacitive-load limits at the intended supply voltage before layout release.
推薦
Active Low-Pass Filter
Use the LMR981G-GTR as the active element in a first-order or higher-order low-pass filter when the signal is referenced to ground and the supply voltage is limited. Its rail-to-rail input and output characteristics provide useful signal range in single-supply systems, while the compact SSOP-6 package leaves room for passive components. Select resistor and capacitor values for the required cutoff and verify that the closed-loop gain remains inside the amplifier's stable operating region. Keep the feedback network compact, connect the bypass capacitor close to the supply pin, and check phase margin against the actual load rather than relying only on nominal gain-bandwidth figures.
推薦
ADC Input Buffer and Driver
The LMR981G-GTR can isolate a sensor or transducer from the sampling input of an ADC, preventing the converter's acquisition transient from affecting the source. Low-voltage operation and rail-to-rail input and output behavior make the amplifier appropriate for compact mixed-signal boards, provided the source impedance and required settling time are compatible with the input capacitance. Place the amplifier adjacent to the ADC input and route the differential or single-ended pair away from digital clocks. Review input bias current, offset, noise, and output-swing limits, because high-resolution conversion performance can be degraded by impedance mismatch or source-current error.
推薦
Battery-Powered Measurement Module
The LMR981G-GTR is appropriate for a battery-powered measurement module that must amplify a low-level analog signal without drawing excessive supply current. The LMR series is specifically positioned for low-voltage, low-supply-current operation, and the single-amplifier configuration avoids the unnecessary circuitry of a dual or quad package. The amplifier can run continuously, or the surrounding system can use a higher-order LMR-family device when a controllable shutdown state is needed. Validate quiescent current, output-current capability, and the minimum operating supply at the highest temperature because battery-life calculations and weak-signal performance are sensitive to those conditions.
推薦
Industrial Control Signal Interface
The LMR981G-GTR can buffer control, feedback, or monitoring signals in a low-voltage industrial control board. Rail-to-rail input capability accepts signals spanning most of the supply range, and the 6-pin SSOP package simplifies routing in densely populated control assemblies. The device is best used for slow or moderate-bandwidth signals where its specified noise, offset, and slew-rate characteristics meet the control-loop requirement. Keep traces away from motors, relays, and power-conversion nodes, and use a dedicated bypass capacitor at the supply pin. For protection against industrial transients, add suitable external clamping and filtering rather than relying on the amplifier's internal structures.
推薦
推薦產品摘要
工程參考資料,適用於 LMR981G-GTR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LMR981G | LMR982G-GTR |
|---|---|---|---|
| Package | 6-pin SSOP, embossed tape-and-reel | 6-pin SSOP ordering variant | 6-pin SSOP ordering variant |
| Brand | ROHM Semiconductor | ROHM Semiconductor | ROHM Semiconductor |
| Number of Amplifiers | 1 circuit | 1 circuit | 1 circuit |
| Amplifier Classification | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier with shutdown |
| Input Type | Rail-to-rail, full swing | Rail-to-rail, full swing | Rail-to-rail, full swing |
| Output Type | Rail-to-rail, full swing | Rail-to-rail, full swing | Rail-to-rail, full swing |
| Low Supply Current | Yes | Yes | Yes |
| Shutdown Function | Not included | Not included | Included |
| Supply Configuration | Single supply | Single supply | Single supply |
主要差異化特點
- Low-power single-amplifier configuration with full-swing operation (對比LMR982G-GTR)
- Compact six-lead SSOP implementation (對比LMR981G)
- General-purpose full-swing signal range (對比LMR982G-GTR)
設計說明
Place the supply bypass capacitor immediately beside the positive supply and ground pins, and connect the amplifier ground directly to the ground plane. Keep the non-inverting input, inverting input, and feedback components away from switching-node copper and fast digital traces. For high-impedance sources, keep the input pins and surrounding copper as small as practical, because surface contamination and leakage can degrade input bias behavior. Use the manufacturer pin configuration to verify all connections before fabrication.
Estimated: with a 5 V supply and a 2 V output, an amplifier delivering 10 mA dissipates roughly (5 V - 2 V) x 10 mA = 30 mW, before accounting for internal bias current. The SSOP-6 package has limited exposed area, so continuous operation near its output-current limit should be checked against the package thermal data and the surrounding copper. Add copper around the device where the board outline permits, and verify junction temperature at the highest expected ambient temperature.
Do not treat rail-to-rail input or output as an unlimited range; input and output headroom change with supply voltage and load current. Avoid driving a large capacitive load directly unless the datasheet's capacitive-load guidance or stability testing supports the application. A shutdown-equipped LMR982-family substitute also requires correct logic-state and startup handling. Review absolute maximum ratings, common-mode limits, output swing, and recommended operating conditions in the manufacturer datasheet.
For gain stages and filters, keep the feedback network compact and use matched resistor layout to minimize parasitic capacitance and thermal gradients. Add small input or output isolation resistors when probing or driving long cables, since they limit capacitive loading and ringing. Validate stability with the actual source resistance, load capacitance, supply decoupling, and PCB ground return. These checks are especially important because rail-to-rail stages may change stability behavior near the supply rails.
合規資訊
The LMR981G-GTR is a general-purpose operational amplifier, so AEC-Q100 is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed from the manufacturer's current compliance documentation for the exact ordering suffix.