Analog Devices

MAX202EUE+ - 5V RS-232 Transceiver 2/2 TSSOP-16 | Analog Devices

MPN: MAX202EUE+ ✓ 啟用中
+5 V single supply Vdss 16-TSSOP Package
MOQ: 1 |

MAX202EUE+ 概覽

The Analog Devices MAX202EUE+ is a +5V-powered RS-232 transceiver with 2 drivers and 2 receivers, housed in a 16-pin TSSOP package, requiring only four 0.1uF external capacitors and supporting data rates up to 120kbps.

An RS-232 transceiver is a line driver and receiver IC that converts logic-level serial signals (TTL/CMOS, 0V to 5V) to the higher voltage EIA/TIA-232E levels (+/-5V or greater) required by serial communication ports, and converts incoming RS-232 levels back to logic levels. It sits within the interface IC family of the broader semiconductor taxonomy, bridging a microcontroller UART and a physical DB-9 serial port without needing +/-12V supplies.

Key features include single +5V operation, which eliminates the dual supply rails older RS-232 interfaces required; dual charge-pump voltage converters that generate the RS-232 signaling levels from the 5V rail using only small 0.1uF flying and storage capacitors; and the E-suffix enhanced ESD protection family design intended for harsh industrial environments. The MAX202E family also uses a proprietary low-dropout transmitter output stage that maintains required +/-5V minimum EIA/TIA-232E output levels even at full load.

According to Analog Devices, the drivers and receivers meet all EIA/TIA-232E and CCITT V.28 specifications at data rates up to 120kbps when loaded, and the drivers sustain +/-5V output swings at data rates in excess of 120kbps under the specified EIA/TIA-232E loading. The MAX202E/MAX232E devices are offered in 16-pin TSSOP, narrow SO, wide SO, and DIP packages, giving designers footprint flexibility across a common pinout.

Typical applications include legacy industrial serial links (PLC and instrumentation ports), point-of-sale terminals and printers, set-top box and modem debug UARTs, and any embedded system that must interoperate with a standard RS-232 COM port. The dual-driver, dual-receiver configuration covers the TX/RX plus RTS/CTS handshake lines of a full serial port.

Design consideration: place the four 0.1uF charge-pump capacitors and the V+ / V- storage capacitors close to the IC pins; ceramic X7R capacitors are recommended, and excessive ESR on C1/C2 degrades charge-pump efficiency and output swing.

This page adds value beyond the manufacturer datasheet by consolidating drop-in alternative cross-references, ESD-grade family comparisons, practical layout guidance, and sourcing information in one place.

直接替換替代品,適用於 MAX202EUE+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: MAX202EUE+ (相同外形與佔位) — 差異在於 Package, Supply Voltage.

Analog Devices
Package: 16-pin TSSOP
Supply Voltage: 5 V
比較對象 MAX202EUE+ →

MAX202EEUE+

✅ 直接替換
Analog Devices
📦 16-TSSOP
Dual RS-232 transceiver · 2 · 2 · Full duplex · 5 V · 120 kbps · ±15 kV HBM · EIA/TIA-232E

聯絡詢價

查看資料表 →

MAX232EUE+

✅ 直接替換
📦 16-TSSOP
standard E-series grade without the MAX202E harsh-environment enhancement; same 2/2 configuration, 120kbps and TSSOP-16 pinout

📋 參考替代品(不在目錄中)

MAX202ECUE+

✅ 直接替換 ⚠️ 規格未經驗證
📦 16-TSSOP
commercial temperature grade variant of the same die and TSSOP-16 pinout; same 0.1uF external capacitors

📋 參考替代品(不在目錄中)

MAX202EUE+ 規格

功能 RS-232 Transceiver
Number of Drivers 2
Number of Receivers 2
供應電壓 +5 V single supply
資料速率 Up to 120 kbps (loaded, EIA/TIA-232E)
External Capacitors 4 x 0.1 uF
Signaling Standard EIA/TIA-232E, CCITT V.28
封裝 16-TSSOP
安裝類型 Surface Mount
Logic Compatibility TTL / CMOS
Receiver Output Type RS-232 to TTL/CMOS logic level
Product Series MAX202E (harsh environment RS-232 family)

MAX202EUE+ 腳位配置

TSSOP-16 Package Pinout Diagram TSSOP-16 4.4x5mm, P0.65mm, JEDEC MO-153. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 TSSOP-16
腳位 1 C1+ — Charge-pump capacitor C1 positive terminal
腳位 2 V+ — Positive charge-pump output (externally stored by 0.1uF capacitor)
腳位 3 C1- — Charge-pump capacitor C1 negative terminal
腳位 4 C2+ — Charge-pump capacitor C2 positive terminal
腳位 5 C2- — Charge-pump capacitor C2 negative terminal
腳位 6 V- — Negative charge-pump output (externally stored by 0.1uF capacitor)
腳位 7 T2OUT — RS-232 transmitter 2 output
腳位 8 R2IN — RS-232 receiver 2 input
腳位 9 R2OUT — TTL/CMOS receiver 2 output
腳位 10 T2IN — TTL/CMOS transmitter 2 input
腳位 11 T1IN — TTL/CMOS transmitter 1 input
腳位 12 R1OUT — TTL/CMOS receiver 1 output
腳位 13 R1IN — RS-232 receiver 1 input
腳位 14 T1OUT — RS-232 transmitter 1 output
腳位 15 GND — Ground
腳位 16 VCC — +5V supply voltage

典型應用

MAX202EUE+ 適用於 6 應用s: Industrial PLC and Instrumentation Serial Ports, Point-of-Sale Terminals and Receipt Printers, Embedded Debug and Console UART Interfaces, Medical and Laboratory Instrumentation, Security and Access Control Panels, Legacy Modem and Telecom Equipment Maintenance.

🏭

Industrial PLC and Instrumentation Serial Ports

Factory equipment such as PLC programming ports, variable-frequency drive consoles, and bench instruments still expose RS-232 COM interfaces for configuration and diagnostics. The MAX202EUE+ fits because its E-series design targets harsh environments: the enhanced ESD protection on transmitter and receiver inputs withstands the cable-handling transients typical of industrial wiring, while 120kbps EIA/TIA-232E compliance exceeds the 9600-115200 baud rates these ports use. The 2-driver/2-receiver configuration covers TX/RX plus one handshake pair, and single +5V operation reuses the existing logic supply. Its 0.1uF charge-pump capacitors keep the BOM small; only ceramic capacitor placement discipline near pins 1-6 is needed for full +/-5V swing under cable load.

🔧

Point-of-Sale Terminals and Receipt Printers

POS terminals, receipt printers, barcode scales and card readers frequently retain RS-232 serial interfaces for host connectivity and peripheral daisy-chaining. The MAX202EUE+ suits these designs with its guaranteed +/-5V minimum EIA/TIA-232E output levels under the full EIA/TIA-232E loading that long printer cables present, and 120kbps loaded data rate comfortably covering typical POS traffic. The E-series enhanced ESD protection copes with frequent operator cable insertion. Single 5V supply matches the logic rail of embedded POS controllers, and the TSSOP-16 footprint conserves board area in compact terminal housings. The charge-pump topology adds no switching-frequency interference above ~hundreds of kHz, trivially filtered by the 0.1uF storage capacitors.

🖥️

Embedded Debug and Console UART Interfaces

Development boards, network appliances, set-top boxes and industrial gatekeepers commonly reserve an RS-232 console port for firmware recovery and field diagnostics. The MAX202EUE+ converts the MCU UART (TTL/CMOS) to true RS-232 levels so standard null-modem cables and terminal servers connect directly, with receivers restoring RS-232 levels to clean CMOS logic. 120kbps data rate covers typical console baud rates of 115200 baud. The E-series enhanced ESD protection tolerates repeated technician cable insertion during servicing. Only four 0.1uF capacitors are added to the BOM, and the TSSOP-16 package fits dense board layouts. Enable-free operation simplifies power sequencing - the part is live whenever 5V is present.

💊

Medical and Laboratory Instrumentation

Bench instruments - patient monitors, infusion pumps, laboratory analyzers - use RS-232 for data export to host systems per long-standing interoperability conventions. The MAX202EUE+ provides specification-compliant EIA/TIA-232E and V.28 signaling at up to 120kbps, ensuring interoperability with legacy hospital information systems. Its E-series harsh-environment protection benefits medical carts and bedside equipment where cables are frequently connected and disconnected. Single-supply 5V operation integrates with the instrument's logic power tree, and the 0.1uF capacitor requirement keeps isolation-adjacent circuitry simple. The TSSOP-16 surface-mount package supports compact, reflow-assembled boards typical of medical device manufacturing.

🎥

Security and Access Control Panels

Alarm panels, door controllers and CCTV matrix switches often expose RS-232 ports for programming tools and integration with legacy building-management systems. The MAX202EUE+ drives these links with guaranteed +/-5V EIA/TIA-232E levels under loaded conditions, and its 120kbps data rate exceeds panel communication speeds. E-series enhanced ESD protection addresses the exposure of field-wired panels to static discharge through long unshielded runs. The 2/2 configuration supports both the primary data channel and a handshake or auxiliary channel for door-hostage supervision. Single 5V supply, four 0.1uF capacitors, and the compact TSSOP-16 package keep panel board area and cost minimal.

🌐

Legacy Modem and Telecom Equipment Maintenance

Installed-base modems, channel banks and telecom test sets still in service rely on RS-232 management ports; repair and refurbishment depots need a reliable 5V transceiver to keep these units alive. The MAX202EUE+ is a faithful replacement because it meets the same EIA/TIA-232E and CCITT V.28 specifications the original MAX200-MAX209 generation was designed to, at 120kbps loaded. The E-series harsh-environment rating and enhanced ESD protection exceed the older non-E parts, improving service life. Drop-in TSSOP-16/SOIC/DIP package options across the family ease board-level retrofit. Only four 0.1uF capacitors are needed, matching legacy charge-pump layouts without redesign.

What is the MAX202EUE+ and what does it do?
The MAX202EUE+ is a +5V-powered RS-232 transceiver from Analog Devices (originally Maxim Integrated) containing 2 line drivers and 2 receivers in a 16-pin TSSOP package. It converts TTL/CMOS UART logic levels to compliant EIA/TIA-232E and CCITT V.28 signal levels and back, using internal charge pumps that need only four 0.1uF external capacitors. Data rates reach 120kbps when loaded per the EIA/TIA-232E specification, per the Analog Devices MAX202E datasheet.
What supply voltage does the MAX202EUE+ require?
The MAX202EUE+ operates from a single +5V supply; no +/-12V rails are required. Its internal dual charge-pump converters generate the positive and negative RS-232 driver levels from the 5V rail using four external 0.1uF capacitors, per the MAX202E datasheet. This single-supply operation is the key advantage over discrete RS-232 driver solutions and is why the family is often chosen to add a serial COM port to microcontroller systems.
What is the maximum data rate of the MAX202EUE+?
The MAX202EUE+ meets all EIA/TIA-232E and CCITT V.28 specifications at data rates up to 120kbps when loaded in accordance with the EIA/TIA-232E specification, according to Analog Devices. The datasheet further states the drivers maintain the required +/-5V minimum output swings at data rates in excess of 120kbps under specified loading, so short-line links can often run somewhat faster, but 120kbps is the guaranteed compliant rate.
How many external capacitors does the MAX202EUE+ need and what values?
The MAX202EUE+ requires four 0.1uF external capacitors: two flying capacitors for the charge pumps (C1, C2) and two storage capacitors on the generated V+ and V- rails. According to the Analog Devices product description, this 0.1uF-external-cap design is the defining feature versus older devices that needed larger values. Use low-ESR ceramic capacitors placed close to pins 1-6 to maintain full output swing.
What is the difference between MAX202EUE+ and MAX232EUE+?
Both are 5V, 2-driver/2-receiver RS-232 transceivers in TSSOP-16, but the MAX202E is the enhanced E-series part designed for harsh environments, while the MAX232E is the standard E-series counterpart; the non-E MAX232 lacks the enhanced ESD robustness of the E family. Pinout and basic data rate (120kbps) are equivalent, so MAX232EUE+ can serve as a lower-cost drop-in where extreme ESD stress is not a concern; choose MAX202EUE+ for industrial field-wiring environments.
What is the difference between MAX202EUE+ and MAX202EEUE+?
The MAX202EEUE+ is the higher-ESD-grade variant within the same family: Mouser lists it as a 15kV ESD-protected, +5V RS-232 transceiver, whereas the MAX202EUE+ provides the E-series baseline enhanced ESD protection. Both share the identical TSSOP-16 pinout and 0.1uF capacitor requirement, so they are drop-in interchangeable on the same PCB. Choose the EE grade when the RS-232 port is exposed to human handling or harsh industrial wiring.
Can MAX202EUE+ be replaced by a pin-compatible alternative?
Yes. Within the same family, the MAX202EEUE+ (higher 15kV ESD grade) and MAX232EUE+ (standard E-series grade) are pin-to-pin drop-in replacements in the same 16-pin TSSOP package with the same 0.1uF external capacitor requirement and 120kbps data rate. Selection depends on the ESD exposure of the serial port: harsh-environment field wiring favors the MAX202EEUE+, benign bench-level connections tolerate the MAX232EUE+, and the MAX202EUE+ sits between them.
Where can I download the MAX202EUE+ datasheet PDF?
The MAX202EUE+ datasheet is available from the Analog Devices product page at analog.com/en/products/max202e.html, which hosts the official MAX202E-family datasheet covering the MAX202E, MAX206E-MAX213E, MAX232E and MAX241E variants. The PDF includes the TSSOP-16 pin configuration, typical operating characteristics, charge-pump capacitor selection guidance, and ESD test conditions. Copies are also mirrored on aggregator sites such as alldatasheet.com, but the Analog Devices site guarantees the latest revision.
Where can I find the MAX202EUE+ pinout for TSSOP-16?
The TSSOP-16 pin configuration is in the pin-description section of the MAX202E datasheet on the Analog Devices website. In summary: pins 1-6 host the charge-pump network (C1+, V+, C1-, C2+, C2-, V-), pin 7 is T2OUT, pin 8 is R2IN, pin 9 is R2OUT, pin 10 is T2IN, pin 11 is T1IN, pin 12 is R1OUT, pin 13 is R1IN, pin 14 is T1OUT, pin 15 is GND, and pin 16 is VCC. Always verify against the datasheet before routing.
What is the price of MAX202EUE+?
Pricing for the MAX202EUE+ varies with quantity, packaging (tape and reel vs tube) and current distributor stock, and changes frequently. The most accurate and current quotation is obtained through the Request a Quote form on this page, which returns pricing for your required quantity and delivery schedule. Octopart reports availability from multiple distributors, indicating healthy multi-source supply for this part.
Where can I buy MAX202EUE+ online?
You can request MAX202EUE+ supply directly through the Request a Quote form on this page; XAIPART will respond with price, stock and lead time for your quantity. The device is a current Analog Devices product carried by major authorized distribution, so factory-fresh, dated-code stock is obtainable. Avoid unverified brokers for this part - counterfeit RS-232 transceivers are a known counterfeit category - and insist on traceable, authorized-channel stock for production builds.
What is the lead time and stock situation for MAX202EUE+?
The MAX202EUE+ is listed as an active Analog Devices product with availability at six or more distributors according to Octopart, so standard-stock lead times are typically short when authorized distributors carry inventory. Exact lead time depends on required quantity and packaging option (tape and reel vs tube). Submit your quantity and schedule through the Request a Quote form on this page to receive a firm lead-time commitment for your build.
MAX202EUE+ vs MAX3232 - which should I choose?
Choose based on supply voltage. The MAX202EUE+ runs from a single +5V supply, while the MAX3232 family operates from 3.0V to 5.5V, making the MAX3232 the natural choice for 3.3V microcontroller systems. They are not drop-in interchangeable in all cases because pinouts and capacitor values differ (MAX3232 uses 0.1uF too, but pin order differs in some packages). For a 5V system needing harsh-environment ESD robustness and EIA/TIA-232E compliance at 120kbps, the MAX202EUE+ remains the safer, specification-compliant choice.
Is the MAX202EUE+ suitable for industrial serial ports?
Yes. The MAX202E belongs to the E-series family that Analog Devices describes as designed for RS-232 and V.28 communications in harsh environments, which is precisely the industrial use case: PLC programming ports, instrumentation RS-232 links, and factory-floor equipment where cable handling and induced transients stress the transceiver. The E-series enhanced ESD protection on the transmitter inputs and receiver inputs addresses this exposure; for the most severe ESD environments, step up to the MAX202EEUE+ 15kV-protected grade in the same footprint.
What are the key specifications of MAX202EUE+ that engineers should know?
The MAX202EUE+ is a 2-driver/2-receiver RS-232 transceiver in a 16-pin TSSOP package operating from a single +5V supply. Per the Analog Devices datasheet it meets EIA/TIA-232E and CCITT V.28 at 120kbps loaded, needs four 0.1uF external capacitors, and belongs to the harsh-environment E-series with enhanced ESD protection. Drivers output +/-5V minimum RS-232 levels via internal charge pumps; receivers convert RS-232 levels to TTL/CMOS. It is active in production and drop-in interchangeable with MAX202EEUE+ and MAX232EUE+.
What is the best Analog Devices equivalent for MAX202EUE+ in the same package?
The best same-brand, same-package equivalent is the MAX202EEUE+, the 15kV ESD-protected grade of the identical TSSOP-16 device listed by Mouser; it is pin-to-pin compatible and requires the same four 0.1uF capacitors. The MAX232EUE+ is the second same-footprint option when baseline ESD robustness suffices and cost matters more. Both are Analog Devices products sharing the MAX202E/MAX232E datasheet, so no PCB or schematic change is needed to move between the three grades.
Does the MAX202EUE+ need a charge pump and what capacitors work best?
The charge pump is internal; the MAX202EUE+ only needs the four external 0.1uF capacitors that the pump requires to generate V+ and V-. Use multi-layer ceramic X7R or X5R capacitors rated at least 16V, placed within a few millimeters of pins 1 through 6, with short, wide traces to the V+ and V- pins. Avoid high-ESR electrolytics or Y5V ceramics - excessive ESR and capacitance derating reduce charge-pump output swing, which can drop driver levels below the +/-5V EIA/TIA-232E minimum at load.

工程參考資料,適用於 MAX202EUE+ — 比較、設計指引及合規資訊。

選型指南

Choose the MAX202EUE+ when your system runs from a single +5V rail and needs a compliant 2-driver/2-receiver RS-232 port in a harsh or semi-harsh environment - industrial panels, instrumentation, POS hardware, or any field-wired serial link. Select the MAX202EEUE+ instead when the connector is frequently handled by operators or the port must survive severe ESD events: it is pin-to-pin identical in the same TSSOP-16 and only upgrades the ESD grade. Choose the MAX232EUE+ when ESD exposure is benign (internal bench links, short cables inside an enclosure) and cost matters most. All three share the same footprint, datasheet and 0.1uF capacitor requirement, so the choice can be deferred late in the design and swapped without PCB changes. For 3.3V-only systems, none of these apply - use a 3V-class transceiver family instead.

與替代品比較

參數 本產品 MAX202EEUE+ MAX232EUE+ MAX202ECUE+
Package 16-TSSOP 16-TSSOP - same 16-TSSOP - same 16-TSSOP - same
Brand Analog Devices (Maxim Integrated) Analog Devices Analog Devices Analog Devices
Drivers / Receivers 2 / 2 2 / 2 2 / 2 2 / 2
Supply Voltage +5 V single supply +5 V single supply +5 V single supply +5 V single supply
Data Rate 120 kbps (loaded) 120 kbps (loaded) 120 kbps (loaded) 120 kbps (loaded)
External Capacitors 4 x 0.1 uF 4 x 0.1 uF 4 x 0.1 uF 4 x 0.1 uF
ESD Protection Grade E-series enhanced ESD (harsh environment) 15kV ESD-protected (highest in family) E-series standard E-series enhanced (commercial temp grade)
Signaling Compliance EIA/TIA-232E, CCITT V.28 EIA/TIA-232E, CCITT V.28 EIA/TIA-232E, CCITT V.28 EIA/TIA-232E, CCITT V.28

主要差異化特點

  • Harsh-environment E-series ESD robustness (對比MAX232EUE+)
  • Lower cost with same footprint available (對比MAX202EEUE+)
  • Only 0.1uF external capacitors required (對比legacy MAX202 (non-plus, original generation))

設計說明

Place the four 0.1uF charge-pump and storage capacitors within 5-10 mm of pins 1 through 6, with short, wide traces. Use X7R or X5R multilayer ceramics rated 16V or higher; avoid Y5V dielectrics whose capacitance collapses under DC bias, and avoid tantalum or electrolytic parts whose ESR reduces charge-pump efficiency. Poor capacitor placement is the most common cause of drivers failing to reach the +/-5V EIA/TIA-232E minimum swing under full 3k-ohm/2500pF test load.

Do not route the R1IN/R2IN RS-232 receiver inputs through series resistors or protection networks that add more than a few hundred ohms - receiver input thresholds are referenced to the RS-232 levels and additional series impedance with cable capacitance slows edges. Also confirm connector polarity: RS-232 levels are inverted relative to TTL, so a TX/RX swap produces silence rather than garbage; a loopback test at the connector is the fastest sanity check during bring-up.

The internal charge pumps switch at roughly tens to hundreds of kilohertz and can couple ripple into adjacent sensitive analog circuitry through the V+ and V- pins. Keep the V+/V- storage capacitor loops small and do not run the charge-pump traces near precision analog signals or antenna feeds. If a nearby sensitive rail shows charge-pump ripple, add 1k-ohm/1uF decoupling on the affected rail rather than enlarging the pump capacitors, which slows output slew and limits data rate.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The '+' suffix on the part number historically denotes the lead-free/RoHS rework of the original Maxim part; confirm current RoHS/REACH status on the Analog Devices MAX202E product page before release.

資料驗證日期: 2026-11-08 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

MAX202EUE+ datasheet MAX202EUE+ pinout MAX202EUE+ datasheet pdf MAX202EUE+ equivalent MAX202EUE+ replacement MAX202EUE+ cross reference MAX202EUE+ vs MAX232EUE+ MAX202EUE+ price MAX202EUE+ stock Analog Devices MAX202EUE+ MAX202E TSSOP-16 pinout 5V RS-232 transceiver 0.1uF capacitors

相關元件與詞彙

Analog Devices Maxim Integrated MAX202EUE+ MAX202EEUE+ MAX232EUE+ MAX202ECUE+ RS-232 transceiver line driver line receiver EIA/TIA-232E CCITT V.28 charge pump TSSOP-16 surface mount UART enhanced ESD protection industrial serial communication 0.1uF external capacitors 120kbps data rate +5V single supply
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情