Analog Devices

MAX232AEWE+ - 200kb/s Dual RS-232 Transceiver | Analog Devices

MPN: MAX232AEWE+ ✓ 啟用中
+5 V Vdss 16-pin SOIC Package
MOQ: 1 |

MAX232AEWE+ 概覽

The Analog Devices MAX232AEWE+ is a +5 V-powered, 2/2 full-duplex RS-232 transceiver with a maximum data rate of 200 kb/s, housed in a 16-pin SOIC package measuring 0.295 inch, or 7.50 mm, in body width. It integrates two RS-232 drivers and two receivers for translating between TTL/CMOS logic levels and bipolar RS-232 signal levels.

An RS-232 transceiver is an interface IC that bridges modern digital logic and the voltage-defined RS-232 serial bus. Its transmitter converts low-voltage logic signals into RS-232-compatible levels, while its receiver converts RS-232 inputs back into logic-compatible signals. Within the broader semiconductor hierarchy, the MAX232AEWE+ is an interface IC, a line-driver and receiver device, and a single-supply communications transceiver.

The principal feature set includes two driver channels, two receiver channels, full-duplex operation, a +5 V supply, and operation up to 200 kb/s. These characteristics make it suitable for equipment that needs bidirectional serial connectivity without implementing separate level-shifting circuits for each direction. The SOIC-16 form factor also supports conventional surface-mount PCB assembly.

MAX232A devices use Maxim's RS-232 interface architecture to support EIA/TIA-232E and V.28/V.24-style communications interfaces. The MAX232AEWE+ operates from a single +5 V rail, allowing the logic-side system to use the same supply as many conventional embedded controllers. Its integrated transmitter and receiver functions make pin and component planning simpler than a discrete bidirectional level-shifter arrangement.

Typical applications include serial service ports, data-acquisition equipment, industrial controllers, test-and-measurement instruments, and embedded systems that exchange RS-232 commands or data with a host computer. The 200 kb/s maximum rate supports legacy serial links while remaining suitable for moderate-throughput control and monitoring traffic. Firmware must configure the host and peripheral for the same baud rate, framing, parity, and handshaking method.

PCB design should place charge-pump and interface capacitors close to their specified pins, maintain short return paths, and provide suitable protection for exposed external cables. Signal integrity and ESD performance depend on connector placement, grounding, transmission-line geometry, and the protection network rather than on the IC alone.

This product page consolidates the MAX232AEWE+ electrical identity, package information, verified cross-reference options, application guidance, and practical PCB considerations to support faster component selection and first-board bring-up.

直接替換替代品,適用於 MAX232AEWE+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: MAX232AEWE+ (相同外形與佔位) — 差異在於 Package, Interface Standard, Logic Compatibility, Product Type, RoHS Status.

Analog Devices
Package: 16-SOIC (NSOIC, narrow body, 0.154" / 3.90 mm width)
RoHS Status: Compliant
比較對象 MAX232AEWE+ →
Maxim Integrated
Package: 16-SOIC
Interface Standard: EIA/TIA-232E, V.28, V.24
Product Type: RS-232 dual transceiver
比較對象 MAX232AEWE+ →
Analog Devices
Package: 16-pin wide SOIC
Interface Standard: RS-232; EIA/TIA-232E and V.28/V.24 family application
Logic Compatibility: CMOS/TTL-compatible digital interface
比較對象 MAX232AEWE+ →

MAX232AESE+

✅ 直接替換
Maxim Integrated
📦 16-SOIC (0.295", 7.50 mm width)
RS-232 dual transceiver · 2 drivers · 2 receivers · 4.5 V to 5.5 V · +5 V · EIA/TIA-232E, V.28, V.24 · 2/2 full-duplex RS-232 · Enhanced CMOS

聯絡詢價

查看資料表 →

MAX232ACSE+T

✅ 直接替換
Analog Devices
📦 16-SOIC (0.295", 7.50 mm width)
RS-232 Transceiver (2 Driver / 2 Receiver) · 200 kbps · 4.5 V to 5.5 V · 2 · 2 · Full · ±30 V (HBM ESD tolerance on RS-232 inputs) · 0 °C to +70 °C (C grade)

聯絡詢價

查看資料表 →

MAX232EWE+

✅ 直接替換 ⚠️ 規格未經驗證
Analog Devices
📦 16-SOIC (0.295", 7.50 mm width)
Dual RS-232 transceiver · RS-232 · 4.5 V to 5.5 V · 5 V · 2 channels · 2 channels · 120 kbps · CMOS

聯絡詢價

查看資料表 →

MAX232CWE+

✅ 直接替換 ⚠️ 規格未經驗證
Analog Devices
📦 16-SOIC (0.295", 7.50 mm width)
RS-232 line driver/receiver transceiver · 4.5 V to 5.5 V · 2 · 2 · RS-232; EIA/TIA-232E and V.28/V.24 family application · Dual RS-232 transmitter · Dual RS-232 receiver · CMOS/TTL-compatible digital interface

聯絡詢價

查看資料表 →

HIN232ACBNZ-T

✅ 直接替換
📦 16-SOIC (0.295", 7.50 mm width)
Cross-brand +5 V 2/2 RS-232 transceiver in a 16-pin SOIC; data-rate and electrical-limit differences must be confirmed against the Renesas datasheet.

📋 參考替代品(不在目錄中)

HIN232ECBZ-T

✅ 直接替換
📦 16-SOIC (0.295", 7.50 mm width)
Cross-brand +5 V 2/2 RS-232 transceiver in a 16-pin SOIC; supply limits, slew rate, and temperature grade require direct comparison.

📋 參考替代品(不在目錄中)

MAX232AEWE+ 規格

Driver Count 2 drivers
Receiver Count 2 receivers
Transceiver Configuration 2/2 full-duplex
Interface Standard RS-232
供應電壓 +5 V
Maximum Data Rate 200 kb/s
封裝 16-pin SOIC
Package Body Width 7.50 mm
Package Body Length 0.295 inch
腳位數 16 pins
安裝類型 Surface mount
Logic Compatibility TTL/CMOS logic interface
RoHS 狀態 unknown
REACH Status unknown

MAX232AEWE+ 0.295 inch 腳位配置指南

MAX232AEWE+(0.295 inch 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

MAX232AEWE+ 的 0.295 inch 封裝腳位圖

無詳細腳位定義資料: MAX232AEWE+.

請參閱 資料表 以查看完整腳位配置。

典型應用

MAX232AEWE+ 適用於 6 應用s: Industrial serial control, Test and measurement instruments, Data acquisition equipment, Embedded serial adapters, Instrument service ports, Point-of-sale and peripheral interfaces.

🏭

Industrial serial control

The MAX232AEWE+ fits industrial equipment that requires a legacy RS-232 service or control port alongside a +5 V digital controller. Its two drivers and two receivers support two communication directions in one 16-pin SOIC, while the 200 kb/s rate covers command exchanges, configuration traffic, and periodic status data. Place the transceiver between the controller UART and the DB9 or terminal connector, then use the manufacturer-recommended charge-pump capacitors. External protection is essential when the cable leaves the controlled enclosure because ESD and surge events occur at the connector rather than inside the logic domain.

🔧

Test and measurement instruments

The MAX232AEWE+ is useful in test and measurement instruments that expose a serial command interface to a legacy host computer. Its 200 kb/s maximum rate supports parameter requests, calibration data, and instrument-status reporting, while the 2/2 full-duplex arrangement permits simultaneous command transmission and response reception. The +5 V supply architecture simplifies integration with control logic operating from the same rail. Keep the interface ground adjacent to the receiver return path, and route the connector-side traces away from sensitive analog and high-impedance measurement circuits to minimize coupling.

📊

Data acquisition equipment

The MAX232AEWE+ can bridge a controller or measurement module to a host using the RS-232 protocol. Two receiver channels allow status or handshake inputs to reach the controller, while two driver channels support outgoing commands and data. The device operates from +5 V and supports links up to 200 kb/s, making it appropriate for moderate-rate acquisition control rather than continuous high-bandwidth transfer. Use local decoupling as specified in the MAX232A datasheet, and terminate or bias unused inputs according to the manufacturer's recommendations to prevent noise-induced transitions.

🖥️

Embedded serial adapters

The MAX232AEWE+ suits compact embedded adapters that expose a legacy serial connector to a modern controller. Its 16-pin SOIC package saves board area compared with separate transmitter and receiver ICs, while the integrated 2/2 arrangement simplifies signal routing. The +5 V rail and 200 kb/s capability are compatible with control, logging, and configuration links. Avoid placing the connector-side interface directly beside switching regulators or fast digital clocks; instead, keep copper paths short and use a protected connector interface designed for the external cable environment.

🔌

Instrument service ports

The MAX232AEWE+ provides a practical interface for service and diagnostic ports on programmable instruments. A service computer can send configuration commands through one driver while the instrument returns measurements or fault status through a receiver, and the second pair supports additional control signals. Its 200 kb/s maximum data rate is suitable for configuration and diagnostic traffic. Firmware should use consistent baud, parity, stop-bit, and flow-control settings, while hardware should include connector-level surge and ESD protection because the external RS-232 cable is the primary electrical threat.

🧩

Point-of-sale and peripheral interfaces

The MAX232AEWE+ can connect peripherals that retain an RS-232 control port to a +5 V embedded controller. Typical uses include configuration exchanges, receipt or ticket-device commands, and status monitoring rather than high-throughput data transfer. The two transmitters and two receivers provide enough channels for common handshake and data arrangements within one 16-pin SOIC. Validate the peripheral's electrical levels and connector polarity before production, and add cable-side protection where the RS-232 port is accessible by users or connected to long external leads.

推薦產品摘要

MAX232AESE Pin-compatible 2/2 RS-232 transceiver option 用於: Industrial serial control, Data acquisition equipment, Embedded serial adapters HIN232ACBNZ-T Cross-manufacturer RS-232 transceiver option 用於: Industrial serial control, Instrument service ports MAX232ACSE Same-family RS-232 interface option 用於: Test and measurement instruments, Instrument service ports MAX232EWE+ Analog Devices 用於: Test and measurement instruments, Point-of-sale and peripheral interfaces HIN232ECBZ-T Cross-brand RS-232 interface candidate 用於: Data acquisition equipment MAX232CWE+ Analog Devices 用於: Embedded serial adapters, Point-of-sale and peripheral interfaces
What is the MAX232AEWE+?
The MAX232AEWE+ is a +5 V-powered RS-232 interface IC containing two drivers and two receivers in a 16-pin SOIC package. According to the Analog Devices MAX232A product page and manufacturer datasheet, it supports bidirectional serial communication at rates up to 200 kb/s. The device is intended for systems that need to connect TTL/CMOS logic to a conventional RS-232 port without separate level-shifting circuitry.
What is the data rate of the MAX232AEWE+?
The MAX232AEWE+ supports a maximum serial data rate of 200 kb/s. The 200 kb/s figure comes from the manufacturer part data and is appropriate for legacy RS-232 control, diagnostic, configuration, and instrumentation links. Actual application throughput will also depend on the UART baud-rate divisor, character framing, protocol overhead, latency, and the connected host software.
How many RS-232 drivers and receivers does the MAX232AEWE+ contain?
The MAX232AEWE+ contains two RS-232 drivers and two receivers, giving it a 2/2 transceiver configuration. The manufacturer describes the device as a dual transmitter and receiver for RS-232 interfaces. This allows two independent signal directions to be implemented in one 16-pin package while retaining a single +5 V supply architecture.
What package does the MAX232AEWE+ use?
The MAX232AEWE+ uses a 16-pin SOIC package with a body width of 0.295 inch, equivalent to 7.50 mm. The package is identified as 16-SOIC in the manufacturer ordering information and is intended for conventional surface-mount assembly. Verify the land pattern against the wide-body SOIC footprint in the manufacturer package drawing before releasing the PCB.
Where can I download the MAX232AEWE+ datasheet PDF?
The MAX232AEWE+ datasheet can be obtained through the Analog Devices MAX232A product page at https://www.analog.com/en/products/max232a.html. The product page provides the manufacturer documentation and ordering information for the MAX232A family. Use the MAX232A datasheet to confirm pin assignments, recommended capacitors, electrical characteristics, and the ordering code corresponding to the 16-pin wide SOIC package.
Where can I find the MAX232AEWE+ pinout?
The MAX232AEWE+ pinout is documented in the MAX232A manufacturer datasheet under the pin-description and package-information sections. The device uses a 16-pin SOIC outline, but PCB assignments should be taken directly from the package drawing rather than inferred from another MAX232 package. Pay particular attention to supply, ground, charge-pump capacitor, driver-output, and receiver-input connections.
Where can I buy MAX232AEWE+ and check its current lead time?
Use the Request a Quote form on this page to request MAX232AEWE+ availability, lead time, order quantity, and a current quotation. The request should include the exact MAX232AEWE+ ordering code and the required delivery destination. This avoids relying on stale catalog availability and allows the manufacturer channel to confirm the production and distribution status for your quantity.
What is the current price of MAX232AEWE+?
The current MAX232AEWE+ quotation is generated through the Request a Quote form on this page. Submit the exact part number, desired quantity, target package format, and delivery location for a current response. Price and availability can change with quantity and market conditions, so request the quotation at the same time as your production schedule is confirmed.
Is the MAX232AEWE+ in stock?
Stock for MAX232AEWE+ should be confirmed through the Request a Quote form on this page because inventory changes by quantity, date, and delivery region. Include your required order quantity, date-code preference, and destination country in the request. The manufacturer product family remains actively documented for new RS-232 interface designs.
What is the best drop-in replacement for MAX232AEWE+?
The MAX232AESE is the closest same-manufacturer drop-in candidate identified for MAX232AEWE+ because it retains the 16-pin SOIC interface and equivalent 2/2 RS-232 transceiver arrangement. HIN232ACBNZ-T is a cross-manufacturer option for designs that confirm its pinout and electrical limits. Always compare the complete manufacturer datasheet before replacing an existing design.
Can MAX232AESE replace MAX232AEWE+?
The MAX232AESE can serve as a drop-in candidate for MAX232AEWE+ because cross-reference information identifies consistent terminals and package dimensions and describes the devices as functionally equivalent. The Analog Devices datasheet remains the controlling document for supply limits, electrical characteristics, temperature range, and capacitor requirements. Confirm those parameters against your operating conditions before production release.
MAX232AEWE+ vs MAX232AESE — which is better for a legacy serial port?
The MAX232AEWE+ and MAX232AESE are closely matched choices for a legacy serial port because both implement a 2/2 RS-232 transceiver in a 16-pin SOIC format and support operation up to 200 kb/s. Choose the ordering code whose temperature grade and production suffix match your assembly and procurement requirements. Confirm the exact manufacturer ordering table for qualification and lifecycle status.
When should I choose MAX232AEWE+ over MAX232ACSE?
Choose the MAX232AEWE+ when its specific ordering code matches your required temperature grade, qualification, and sourcing conditions. Choose the MAX232ACSE only after confirming that its electrical characteristics, pin assignment, package details, and operating-temperature limits satisfy the design. The devices are functionally close, so procurement grade and exact datasheet revision are usually the decisive factors.
Is MAX232AEWE+ suitable for industrial serial equipment?
The MAX232AEWE+ is suitable for industrial serial equipment when the selected ordering grade covers the required ambient temperature and the interface remains inside its rated electrical limits. Its two drivers, two receivers, +5 V supply, and 200 kb/s rate suit equipment-control and data-acquisition links. Add external surge and ESD protection for cables that leave the enclosure.
What are the key specifications of MAX232AEWE+ that engineers should know?
The key MAX232AEWE+ specifications are two RS-232 drivers, two receivers, a 2/2 full-duplex arrangement, +5 V operation, a 200 kb/s maximum data rate, and a 16-pin SOIC package with a 7.50 mm body width. According to the manufacturer datasheet and product page, the device combines bidirectional serial conversion in one surface-mount package. Detailed electrical limits and recommended external components should be taken from the exact MAX232A documentation.
What can replace MAX232AEWE+?
MAX232AESE is a direct same-manufacturer replacement candidate for MAX232AEWE+, while MAX232ACSE offers another close MAX232A-family option in a 16-pin SOIC. Cross-manufacturer choices include HIN232ACBNZ-T and HIN232ECBZ-T, subject to package and pin verification. The MAX232AEWE+ remains preferable when exact ordering-code continuity, qualification records, and known configuration matter.

工程參考資料,適用於 MAX232AEWE+ — 比較、設計指引及合規資訊。

選型指南

Choose the MAX232AEWE+ when maintaining an established +5 V, 16-pin SOIC RS-232 design and minimizing changes to the schematic, PCB, and approved component list are the priorities. Its two drivers, two receivers, full-duplex operation, and 200 kb/s rate cover typical control, diagnostic, and service-port requirements. MAX232AESE is the closest same-manufacturer drop-in candidate when its exact temperature grade and ordering information meet the design; MAX232ACSE should be selected only after checking the relevant MAX232A ordering characteristics. MAX232EWE+ and MAX232CWE+ can be useful for existing MAX232-family platforms, but family-specific enable or shutdown behavior may require schematic review. HIN232ACBNZ-T or HIN232ECBZ-T can support second sourcing after their pinouts, electrical limits, temperature grades, and external-capacitor requirements are verified against the Renesas datasheet.

與替代品比較

參數 本產品 MAX232AESE MAX232ACSE MAX232EWE+ MAX232CWE+ HIN232ACBNZ-T HIN232ECBZ-T
Brand Analog Devices Analog Devices Analog Devices Maxim Integrated Maxim Integrated Renesas Electronics Renesas Electronics
Package 16-SOIC (0.295", 7.50 mm width) 16-SOIC (0.295", 7.50 mm width) 16-SOIC (0.295", 7.50 mm width) 16-SOIC (0.295", 7.50 mm width) 16-SOIC (0.295", 7.50 mm width) 16-SOIC (0.295", 7.50 mm width) 16-SOIC (0.295", 7.50 mm width)
Driver and Receiver Count 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers
Interface Standard RS-232 RS-232 RS-232 RS-232 RS-232 RS-232 RS-232
Supply Voltage +5 V +5 V +5 V +5 V +5 V +5 V +5 V
Transceiver Configuration 2/2 full-duplex 2/2 full-duplex 2/2 full-duplex 2/2 full-duplex 2/2 full-duplex 2/2 full-duplex 2/2 full-duplex

主要差異化特點

  • Combines two drivers and two receivers in one 16-pin SOIC (對比MAX232AESE)
  • Single +5 V interface architecture (對比HIN232ACBNZ-T)
  • Supports a 200 kb/s RS-232 data rate (對比MAX232CWE+)

設計說明

Route the MAX232AEWE+ close to the connector and logic interface rather than scattering the level-shifting path across the board. Keep the charge-pump capacitor connections and supply traces short, use the package footprint specified by the manufacturer, and provide a continuous ground reference beneath the device. This reduces switching-current loop area and helps prevent connector-side transients from coupling into sensitive logic.

Do not assume that a 16-SOIC footprint alone proves compatibility. Compare every MAX232A ordering code for temperature grade, shutdown or enable behavior, receiver thresholds, data rate, supply limits, and external-capacitor requirements. Before substituting a candidate, update the schematic symbols and verify the PCB land pattern, especially for any wide-body versus narrow-body SOIC package.

Place connector protection and the transceiver in a deliberate signal path: logic pins toward the digital circuitry and driver or receiver pins toward the connector. Route the return conductor with the signal path, avoid sharing narrow ground traces between the interface and switching converters, and add an external ESD or surge network where the cable is exposed. The IC alone does not protect the port from external cable transients.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The MAX232A family supports RS-232 communications interfaces, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact ordering code. AEC-Q100 is not applicable to this commercial interface IC.

相關搜尋

MAX232AEWE+ datasheet MAX232AEWE+ datasheet pdf MAX232AEWE+ pinout MAX232AEWE+ equivalent MAX232AEWE+ replacement MAX232AEWE+ cross reference MAX232AEWE+ price MAX232AEWE+ stock Analog Devices MAX232AEWE+ MAX232AEWE+ 16-SOIC pinout MAX232AEWE+ vs MAX232AESE MAX232AEWE+ RS-232 application circuit

相關元件與詞彙

Analog Devices Maxim Integrated MAX232AEWE+ MAX232A MAX232AESE MAX232ACSE MAX232EWE+ MAX232CWE+ HIN232ACBNZ-T HIN232ECBZ-T RS-232 RS-232 transceiver interface IC line driver line receiver full-duplex transceiver TTL logic CMOS logic 16-SOIC SOIC family surface-mount package 200 kb/s EIA/TIA-232E V.28 V.24
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情