MAX232AEWE+ - 200kb/s Dual RS-232 Transceiver | Analog Devices
MPN: MAX232AEWE+ ✓ AktifMAX232AEWE+ Genel Bakış
An RS-232 transceiver is an interface IC that bridges modern digital logic and the voltage-defined RS-232 serial bus. Its transmitter converts low-voltage logic signals into RS-232-compatible levels, while its receiver converts RS-232 inputs back into logic-compatible signals. Within the broader semiconductor hierarchy, the MAX232AEWE+ is an interface IC, a line-driver and receiver device, and a single-supply communications transceiver.
The principal feature set includes two driver channels, two receiver channels, full-duplex operation, a +5 V supply, and operation up to 200 kb/s. These characteristics make it suitable for equipment that needs bidirectional serial connectivity without implementing separate level-shifting circuits for each direction. The SOIC-16 form factor also supports conventional surface-mount PCB assembly.
MAX232A devices use Maxim's RS-232 interface architecture to support EIA/TIA-232E and V.28/V.24-style communications interfaces. The MAX232AEWE+ operates from a single +5 V rail, allowing the logic-side system to use the same supply as many conventional embedded controllers. Its integrated transmitter and receiver functions make pin and component planning simpler than a discrete bidirectional level-shifter arrangement.
Typical applications include serial service ports, data-acquisition equipment, industrial controllers, test-and-measurement instruments, and embedded systems that exchange RS-232 commands or data with a host computer. The 200 kb/s maximum rate supports legacy serial links while remaining suitable for moderate-throughput control and monitoring traffic. Firmware must configure the host and peripheral for the same baud rate, framing, parity, and handshaking method.
PCB design should place charge-pump and interface capacitors close to their specified pins, maintain short return paths, and provide suitable protection for exposed external cables. Signal integrity and ESD performance depend on connector placement, grounding, transmission-line geometry, and the protection network rather than on the IC alone.
This product page consolidates the MAX232AEWE+ electrical identity, package information, verified cross-reference options, application guidance, and practical PCB considerations to support faster component selection and first-board bring-up.
Drop-in alternatifler için MAX232AEWE+ — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller MAX232AEWE+ (aynı form faktörü ve ayağa oturma) — farklı olan Package, Interface Standard, Logic Compatibility, Product Type, RoHS Status.
MAX232AESE+
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MAX232ACSE+T
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MAX232EWE+
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MAX232CWE+
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →HIN232ACBNZ-T
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
HIN232ECBZ-T
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MAX232AEWE+ Özellikler
| Driver Count | 2 drivers |
| Receiver Count | 2 receivers |
| Transceiver Configuration | 2/2 full-duplex |
| Interface Standard | RS-232 |
| Besleme Gerilimi | +5 V |
| Maximum Data Rate | 200 kb/s |
| Paket | 16-pin SOIC |
| Package Body Width | 7.50 mm |
| Package Body Length | 0.295 inch |
| Pin Sayısı | 16 pins |
| Montaj Türü | Surface mount |
| Logic Compatibility | TTL/CMOS logic interface |
| RoHS Durumu | unknown |
| REACH Status | unknown |
MAX232AEWE+ 0.295 inch Pin Yapısı Kılavuzu
MAX232AEWE+ (0.295 inch paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: MAX232AEWE+.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
MAX232AEWE+ için uygundur 6 uygulamas: Industrial serial control, Test and measurement instruments, Data acquisition equipment, Embedded serial adapters, Instrument service ports, Point-of-sale and peripheral interfaces.
Industrial serial control
The MAX232AEWE+ fits industrial equipment that requires a legacy RS-232 service or control port alongside a +5 V digital controller. Its two drivers and two receivers support two communication directions in one 16-pin SOIC, while the 200 kb/s rate covers command exchanges, configuration traffic, and periodic status data. Place the transceiver between the controller UART and the DB9 or terminal connector, then use the manufacturer-recommended charge-pump capacitors. External protection is essential when the cable leaves the controlled enclosure because ESD and surge events occur at the connector rather than inside the logic domain.
Önerilen
Test and measurement instruments
The MAX232AEWE+ is useful in test and measurement instruments that expose a serial command interface to a legacy host computer. Its 200 kb/s maximum rate supports parameter requests, calibration data, and instrument-status reporting, while the 2/2 full-duplex arrangement permits simultaneous command transmission and response reception. The +5 V supply architecture simplifies integration with control logic operating from the same rail. Keep the interface ground adjacent to the receiver return path, and route the connector-side traces away from sensitive analog and high-impedance measurement circuits to minimize coupling.
Önerilen
Data acquisition equipment
The MAX232AEWE+ can bridge a controller or measurement module to a host using the RS-232 protocol. Two receiver channels allow status or handshake inputs to reach the controller, while two driver channels support outgoing commands and data. The device operates from +5 V and supports links up to 200 kb/s, making it appropriate for moderate-rate acquisition control rather than continuous high-bandwidth transfer. Use local decoupling as specified in the MAX232A datasheet, and terminate or bias unused inputs according to the manufacturer's recommendations to prevent noise-induced transitions.
Önerilen
Embedded serial adapters
The MAX232AEWE+ suits compact embedded adapters that expose a legacy serial connector to a modern controller. Its 16-pin SOIC package saves board area compared with separate transmitter and receiver ICs, while the integrated 2/2 arrangement simplifies signal routing. The +5 V rail and 200 kb/s capability are compatible with control, logging, and configuration links. Avoid placing the connector-side interface directly beside switching regulators or fast digital clocks; instead, keep copper paths short and use a protected connector interface designed for the external cable environment.
Önerilen
Instrument service ports
The MAX232AEWE+ provides a practical interface for service and diagnostic ports on programmable instruments. A service computer can send configuration commands through one driver while the instrument returns measurements or fault status through a receiver, and the second pair supports additional control signals. Its 200 kb/s maximum data rate is suitable for configuration and diagnostic traffic. Firmware should use consistent baud, parity, stop-bit, and flow-control settings, while hardware should include connector-level surge and ESD protection because the external RS-232 cable is the primary electrical threat.
Önerilen
Point-of-sale and peripheral interfaces
The MAX232AEWE+ can connect peripherals that retain an RS-232 control port to a +5 V embedded controller. Typical uses include configuration exchanges, receipt or ticket-device commands, and status monitoring rather than high-throughput data transfer. The two transmitters and two receivers provide enough channels for common handshake and data arrangements within one 16-pin SOIC. Validate the peripheral's electrical levels and connector polarity before production, and add cable-side protection where the RS-232 port is accessible by users or connected to long external leads.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: MAX232AEWE+ — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MAX232AESE | MAX232ACSE | MAX232EWE+ | MAX232CWE+ | HIN232ACBNZ-T | HIN232ECBZ-T |
|---|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Maxim Integrated | Maxim Integrated | Renesas Electronics | Renesas Electronics |
| Package | 16-SOIC (0.295", 7.50 mm width) | 16-SOIC (0.295", 7.50 mm width) | 16-SOIC (0.295", 7.50 mm width) | 16-SOIC (0.295", 7.50 mm width) | 16-SOIC (0.295", 7.50 mm width) | 16-SOIC (0.295", 7.50 mm width) | 16-SOIC (0.295", 7.50 mm width) |
| Driver and Receiver Count | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Interface Standard | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V | +5 V | +5 V | +5 V |
| Transceiver Configuration | 2/2 full-duplex | 2/2 full-duplex | 2/2 full-duplex | 2/2 full-duplex | 2/2 full-duplex | 2/2 full-duplex | 2/2 full-duplex |
Ana Farklılayıcılar
- Combines two drivers and two receivers in one 16-pin SOIC (karşılaştırma:MAX232AESE)
- Single +5 V interface architecture (karşılaştırma:HIN232ACBNZ-T)
- Supports a 200 kb/s RS-232 data rate (karşılaştırma:MAX232CWE+)
Tasarım Notları
Route the MAX232AEWE+ close to the connector and logic interface rather than scattering the level-shifting path across the board. Keep the charge-pump capacitor connections and supply traces short, use the package footprint specified by the manufacturer, and provide a continuous ground reference beneath the device. This reduces switching-current loop area and helps prevent connector-side transients from coupling into sensitive logic.
Do not assume that a 16-SOIC footprint alone proves compatibility. Compare every MAX232A ordering code for temperature grade, shutdown or enable behavior, receiver thresholds, data rate, supply limits, and external-capacitor requirements. Before substituting a candidate, update the schematic symbols and verify the PCB land pattern, especially for any wide-body versus narrow-body SOIC package.
Place connector protection and the transceiver in a deliberate signal path: logic pins toward the digital circuitry and driver or receiver pins toward the connector. Route the return conductor with the signal path, avoid sharing narrow ground traces between the interface and switching converters, and add an external ESD or surge network where the cable is exposed. The IC alone does not protect the port from external cable transients.
Uyumluluk Bilgisi
The MAX232A family supports RS-232 communications interfaces, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact ordering code. AEC-Q100 is not applicable to this commercial interface IC.