MAX232ESE+T - 120kbps RS-232 Transceiver | Analog Devices
MPN: MAX232ESE+T ✓ 啟用中MAX232ESE+T 概覽
An RS-232 transceiver is an interface IC that combines a transmitter and receiver in one package. A line driver converts logic-level signals into differential, bipolar RS-232 signals, while a line receiver converts bipolar signals back into logic levels. The MAX232ESE+T belongs to the broader RS-232 interface transceiver category, where EIA/TIA-232E, V.28, and V.24 define the electrical behavior and communication characteristics of the interface.
The device includes two transmit channels and two receive channels in a 16-pin SOIC. According to the manufacturer product page, the MAX232E family meets EIA/TIA-232E and CCITT V.28 specifications at data rates up to 120 kbps when loaded. This makes the part suitable for legacy serial ports, industrial equipment, service interfaces, and embedded systems that retain an RS-232 connection.
The MAX232ESE+T combines a +5 V supply with on-chip charge-pump circuitry for the negative driver voltage. This integration allows the interface to operate without a separate negative supply, while the capacitive charge pump adds only a small number of external charge-pump capacitors. The E designation denotes the enhanced MAX232 family, while the suffix identifies the package, temperature option, and lead-free tape-and-reel shipping configuration.
Typical uses include RS-232 links between industrial controllers and service equipment, configuration ports on network appliances, legacy printer and instrument interfaces, and diagnostic connections on embedded systems. Designers should treat the RS-232 driver outputs as not tolerant of the negative voltages found on telephone lines, and they should provide the charge-pump and interface capacitors specified by the manufacturer.
For PCB layout, place the charge-pump capacitors and VCC bypass capacitor close to their associated device pins, and route each driver output directly to its RS-232 connector. Keep logic-side traces away from the higher-voltage driver outputs to reduce capacitive coupling and data errors, especially when long connector cables are attached.
This product page combines the manufacturer’s device description, distributor package identification, lifecycle information, replacement analysis, and practical RS-232 layout guidance. It is intended to help engineers verify electrical fit, package compatibility, sourcing requirements, and board-level implementation before committing a MAX232ESE+T to a new or existing design.
直接替換替代品,適用於 MAX232ESE+T — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX232ESE+T (相同外形與佔位) — 差異在於 Product Type, Operating Temperature Range, Interface Standard, Package, Supply Voltage.
MAX232EESE
✅ 直接替換📋 參考替代品(不在目錄中)
MAX232EIDWG4
✅ 直接替換聯絡詢價
查看資料表 →MAX232ECDWRG4
✅ 直接替換聯絡詢價
查看資料表 →MAX232CSE+T
✅ 直接替換聯絡詢價
查看資料表 →MAX202ECWE+T
✅ 直接替換聯絡詢價
查看資料表 →MAX232ESE+T 規格
| Product Type | RS-232 transceiver interface IC |
| Driver and Receiver Configuration | 2 drivers and 2 receivers |
| 供應電壓 | 4.5 V to 5.5 V |
| Maximum Data Rate | 120 kbps |
| Interface Standard | EIA/TIA-232E and CCITT V.28 |
| Supported Voltage Interface | V.28 and V.24 |
| Negative Rail Generation | On-chip capacitive voltage generator |
| 腳位數 | 16 pins |
| 封裝 | 16-pin SOIC |
| 安裝類型 | Surface mount |
| Lead-Free Status | Lead-free ordering suffix |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
| AEC-Q100 Qualification | not_applicable |
MAX232ESE+T 16-pin soic 腳位配置指南
MAX232ESE+T(16-pin soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX232ESE+T.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX232ESE+T 適用於 6 應用s: Industrial Controller Serial Port, Network Equipment Configuration Port, Test and Measurement Instrument, Legacy Printer Interface, Embedded System Debug Interface, Serial Port Expansion.
Industrial Controller Serial Port
The MAX232ESE+T is suitable for adding a legacy RS-232 service port to an industrial controller that operates from a 4.5 V to 5.5 V supply. Its two-driver and two-receiver arrangement supports bidirectional communication on one interface, while the manufacturer-rated 120 kbps rate is appropriate for configuration tools, diagnostic software, and supervisory equipment. The integrated charge-pump architecture generates the negative RS-232 voltage without requiring a separate negative rail, simplifying the power architecture. PCB implementation should preserve short charge-pump capacitor connections and isolate the bipolar driver traces from sensitive logic and sensor signals.
推薦
Network Equipment Configuration Port
The MAX232ESE+T provides a conventional RS-232 connection for configuring or servicing network equipment from a legacy terminal or service laptop. Two full RS-232 channels allow command and status traffic when the host equipment uses separate transmit and receive paths. The MAX232ESE+T supports rates up to 120 kbps, which is sufficient for configuration menus, diagnostic logs, and boot-loader interfaces. Its 16-pin SOIC package simplifies rework and footprint reuse, while the +5 V operation permits implementation alongside modern digital control logic. Connector-side surge and signal-conditioning requirements should be handled separately from the IC interface.
推薦
Test and Measurement Instrument
The MAX232ESE+T can bridge a modern instrument controller to equipment that exposes an RS-232 command or measurement port. At the maximum 120 kbps supported by the MAX232E family, the interface is well suited to short control protocols, instrument identification queries, and transfer of moderate-sized configuration or measurement blocks. The integrated charge pump means the test equipment does not need to generate a negative RS-232 supply. Designers should use the manufacturer-recommended charge-pump and bypass capacitors and keep the connector interface physically separated from sensitive analog measurement circuitry to minimize coupling.
推薦
Legacy Printer Interface
The MAX232ESE+T can provide the electrical interface between a controller and a legacy RS-232 printer or terminal. Two drivers and two receivers permit full-duplex command and status communication, and the 120 kbps capability is more than adequate for printer control and receipt-data transfer. Because the device operates from a +5 V supply and creates the required negative voltage internally, it is particularly useful for embedded controller boards that no longer provide a negative rail. The PCB should route each channel to the correct connector signal, and protection components should be selected for the actual cable environment and grounding arrangement.
推薦
Embedded System Debug Interface
The MAX232ESE+T is appropriate for a manufacturing or field-debug interface on an embedded control system. The 120 kbps interface can carry bootloader messages, diagnostic logs, firmware status, and configuration data without requiring a separate negative supply. Its 16-pin SOIC package supports compact board layouts and straightforward assembly, while the two-channel arrangement can support either one complete RS-232 port plus auxiliary signals or split communication paths. Firmware should match the serial baud rate, framing, parity, and handshake behavior to the physical connection, and production software should avoid relying on undocumented driver-enable timing.
推薦
Serial Port Expansion
The MAX232ESE+T can expand a system that already uses a UART but requires a standards-compliant RS-232 electrical interface. Connecting the UART logic signals to the MAX232 drivers and receivers creates a robust port for peripherals, service tools, or upstream control equipment. The 120 kbps operating rate supports conventional asynchronous serial communications, and the integrated charge pump reduces the power-supply complexity relative to discrete driver-receiver implementations using external negative supplies. Correct implementation requires the specified external capacitors, suitable ground references, and deliberate separation between logic-side and connector-side traces.
推薦
推薦產品摘要
工程參考資料,適用於 MAX232ESE+T — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX232EESE | MAX232EIDWG4 | MAX232ECDWRG4 | MAX232CSE+T | MAX202ECWE+T |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | 2/2 full RS-232 transceiver | 2/2 full RS-232 transceiver | MAX232E RS-232 transceiver | MAX232E RS-232 transceiver | MAX232 RS-232 transceiver | MAX202 RS-232 transceiver |
| Number of Drivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Number of Receivers | 2 | 2 | 2 | 2 | 2 | 2 |
| Number of Pins | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins |
| Negative Voltage Generation | Integrated capacitive voltage generator | Integrated capacitive voltage generator | Integrated capacitive voltage generator | Integrated capacitive voltage generator | Integrated capacitive voltage generator | Integrated capacitive voltage generator |
| Ordering Suffix | ESE+T lead-free tape-and-reel configuration | ESE without +T | EIDWG4 | ECDWRG4 | CSE+T | ECWE+T |
主要差異化特點
- Single-supply RS-232 operation (對比MAX202ECWE+T)
- Full-duplex channel count in a 16-pin SOIC (對比MAX232EESE)
- Established 120 kbps MAX232E positioning (對比MAX232CSE+T)
- Package-compatible consolidation (對比MAX232EIDWG4)
設計說明
Place the external charge-pump capacitors and the VCC bypass capacitor directly beside their associated MAX232ESE+T pins. Keep the charge-pump current loop compact, use a short ground return, and connect the bypass capacitor to the same quiet ground reference used by the device. This minimizes switching transients at the supply pins and helps preserve command integrity when the RS-232 line is active.
Separate logic-side UART traces from RS-232 connector-side driver outputs. Avoid routing driver outputs parallel to clocks, ADC inputs, or sensitive analog signals, and avoid routing beneath long connector or protection components. Where the cable interface is exposed to substantial electrostatic discharge, add a protection strategy that is compatible with the connector and ground architecture rather than relying on the transceiver alone.
Do not treat the MAX232E driver outputs as telephone-line or ±12 V tolerant. Confirm enable polarity, supply voltage, baud rate, framing, and connector signal assignments against the manufacturer datasheet before fabrication. Also verify the exact ESE and +T ordering suffix because related MAX232 and MAX202 variants can share a 16-pin SOIC outline while differing in temperature grade, qualification, or lifecycle status.
Decouple VCC at the device rather than relying on a distant regulator capacitor. The MAX232ESE+T operates from a 4.5 V to 5.5 V supply, and its charge-pump circuitry requires the external capacitors specified by the manufacturer. Keep the charge-pump capacitor loop short and provide an adequate local ground path so switching activity does not disturb nearby digital or analog circuitry.
合規資訊
The +T ordering suffix identifies the lead-free tape-and-reel configuration. RoHS, REACH, halogen-free, and conflict-minerals status were not confirmed from the cited manufacturer pages.