Analog Devices

MAX3232ECPE+ - ±15kV ESD RS-232 Transceiver | Analog Devices

MPN: MAX3232ECPE+ ✓ 啟用中
3.0V to 5.5V Vdss Down to 10nA Id 16-pin PDIP Package
MOQ: 1 |

MAX3232ECPE+ 概覽

The MAX3232ECPE+ from Analog Devices is a dual RS-232 transceiver designed for low-voltage serial interfaces, with two transmit channels, two receive channels, and integrated charge-pump circuitry. It operates from a 3.0V to 5.5V supply, supports data rates up to 1Mbps, and is specified for ±15kV ESD protection on the RS-232 connection pins. The device is packaged in a 16-pin PDIP package.

An RS-232 transceiver is an interface IC that translates logic-level UART signals into RS-232 voltage levels and converts incoming RS-232 signals back to logic levels. The MAX3232 belongs to the broader RS-232 interface family, supporting communication between modern microcontrollers, computers, industrial controllers, and legacy serial equipment. Its integrated charge pump generates the positive and negative voltage rails required by the RS-232 transmitter outputs.

Key features include a 3.0V to 5.5V operating supply range, operation at data rates up to 1Mbps, low-power operation, and enhanced electrostatic-discharge protection. The MAX3232ECPE+ is identified as a true RS-232 transceiver, and the manufacturer describes the MAX3232 family as compatible with the MAX232 family in pin, package, and function for supported variants.

The MAX3232ECPE+ is suitable for systems that need dual-channel RS-232 connectivity without using a higher-voltage supply for the interface. The internal charge-pump design allows the device to operate from a single low-voltage supply while producing the bipolar voltage levels expected by RS-232 receivers. The maximum specified data rate of 1Mbps supports high-speed asynchronous serial links where cable length, termination, and signal integrity are properly controlled.

Typical applications include industrial control equipment, data acquisition systems, instrumentation, point-of-sale terminals, service interfaces, and embedded systems that communicate with RS-232 peripherals. The dual-driver and dual-receiver arrangement supports either two independent transmit paths, two independent receive paths, or a combination of full-duplex RS-232 links.

PCB layout should keep the charge-pump capacitors and the RS-232 connector-side protection network close to the device. The DIP package is suitable for prototyping, legacy industrial equipment, and through-hole industrial control boards where a surface-mount package is not required. Before production use, verify the complete pin assignment, recommended capacitor values, ESD layout, and operating limits against the manufacturer datasheet.

直接替換替代品,適用於 MAX3232ECPE+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: MAX3232ECPE+ (相同外形與佔位) — 差異在於 Maximum Data Rate, Mounting Type, Supply Voltage Range, ESD Protection, Interface Standard.

Maxim Integrated
Maximum Data Rate: 1 Mbps
Mounting Type: Through Hole
Supply Voltage Range: 3.0 V to 5.5 V
比較對象 MAX3232ECPE+ →
Analog Devices
Maximum Data Rate: 1 Mbps
Mounting Type: Surface mount
Supply Voltage Range: 3.0 V to 5.5 V
比較對象 MAX3232ECPE+ →
Analog Devices
Maximum Data Rate: Up to 1Mbps
Interface Standard: True RS-232
比較對象 MAX3232ECPE+ →

MAX3232CPE+

✅ 直接替換
Maxim Integrated
📦 16-PDIP
RS-232 transceiver · 2 · 2 · 3.0 V to 5.5 V · 1 Mbps · 4 x 0.1 uF · True RS-232 · TTL/CMOS

聯絡詢價

查看資料表 →

MAX3232ECPE

✅ 直接替換
📦 16-PDIP
Same MAX3232E 16-PDIP transceiver and ±15kV ESD rating, differing only in the ordering suffix and associated qualification details.

📋 參考替代品(不在目錄中)

MAX3232ECPE+ 規格

Product Type Dual RS-232 transceiver
Number of Transmit Channels 2
Number of Receive Channels 2
Supply Voltage Range 3.0V to 5.5V
Maximum Data Rate 1Mbps
ESD Protection ±15kV
Low-Power Supply Current Down to 10nA
RS-232 Standard True RS-232
Package Type 16-pin PDIP
安裝類型 Through-hole
Charge Pump Dual charge-pump circuit

MAX3232ECPE+ 16-pin pdip 腳位配置指南

MAX3232ECPE+(16-pin pdip 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

MAX3232ECPE+ 的 16-pin pdip 封裝腳位圖

無詳細腳位定義資料: MAX3232ECPE+.

請參閱 資料表 以查看完整腳位配置。

典型應用

MAX3232ECPE+ 適用於 6 應用s: Industrial serial control, Data acquisition systems, Point-of-sale and service terminals, Embedded serial instrumentation, RS-232 test and measurement interface, Legacy equipment refurbishment.

🏭

Industrial serial control

The MAX3232ECPE+ is suitable for industrial controllers that must communicate with RS-232 test equipment, service ports, or legacy machinery. Its two transmitters and two receivers can support two serial links or one full-duplex channel, while the 3.0V to 5.5V operating range fits both 3.3V and 5V control platforms. Operation up to 1Mbps provides useful performance margin for short industrial links. The ±15kV ESD rating is valuable where cables connect to exposed service connectors, although the enclosure, grounding, and surge strategy must still be engineered for the installation.

📟

Data acquisition systems

The MAX3232ECPE+ can bridge a modern controller to RS-232 data-acquisition instruments that retain legacy serial interfaces. The dual-channel arrangement allows separate transmit and receive paths or two instrument connections when the protocol permits. Its low-voltage 3.0V to 5.5V operation simplifies integration with embedded controllers, while the integrated charge pump supplies the bipolar levels required for true RS-232 communication. For laboratory and production-floor use, place the transceiver close to the connector and follow the manufacturer’s recommended capacitor and protection layout.

🖥️

Point-of-sale and service terminals

The MAX3232ECPE+ fits point-of-sale controllers, peripheral interfaces, and service terminals that communicate with RS-232 equipment through a wired connector. Two drivers and two receivers provide flexible channel allocation, while the maximum 1Mbps rate supports common asynchronous serial protocols. The 3.0V to 5.5V supply range reduces the need for a dedicated high-voltage interface supply, and the E-series ±15kV ESD protection adds robustness at externally accessible ports. Correct grounding and cable-length limits remain essential for dependable field operation.

🔧

Embedded serial instrumentation

The MAX3232ECPE+ allows an embedded controller to communicate with legacy oscilloscopes, printers, meters, and service equipment that use RS-232. Because the transceiver runs from 3.0V to 5.5V, it can sit beside a low-voltage processor without a separate high-voltage supply. Its integrated charge pump simplifies the interface and supports data rates up to 1Mbps. The 16-pin PDIP format is particularly convenient for prototype boards and legacy through-hole assemblies, while a surface-mount MAX3232E family option can be considered for newer compact products.

📊

RS-232 test and measurement interface

The MAX3232ECPE+ is appropriate for test and measurement equipment that must communicate with older RS-232 controllers, fixtures, or analyzers. The dual receiver and dual driver organization can support bidirectional instrumentation or two independent serial ports. Operation up to 1Mbps is useful for short bench links, while the integrated charge pump eliminates the need for external switched-capacitor inverter components. For reliable measurements, use a qualified RS-232 cable, maintain a common ground where appropriate, and keep the transceiver and connector routing away from high-energy switching nodes.

🔧

Legacy equipment refurbishment

The MAX3232ECPE+ is useful when repairing or upgrading equipment that originally used a MAX3232-family RS-232 interface in a 16-pin PDIP footprint. Its dual-transmitter, dual-receiver arrangement and true RS-232 operation preserve the role of the original interface while allowing the surrounding controller to operate from 3.0V to 5.5V. The E-series ±15kV ESD protection is useful during repeated cable connection in service environments. Before installation, verify pin orientation, required charge-pump capacitors, connector shielding, and the complete operating-temperature range.

What is the MAX3232ECPE+?
The MAX3232ECPE+ is a dual RS-232 transceiver with two transmit channels, two receive channels, and integrated charge-pump circuitry. Analog Devices lists the MAX3232 family as operating from 3.0V to 5.5V, supporting data rates up to 1Mbps, and providing true RS-232 operation. The MAX3232ECPE+ is supplied in a 16-pin PDIP package. According to the manufacturer product page, the MAX3232 family also provides pin, package, and functional compatibility with the MAX232 family for applicable variants.
What is the operating voltage of MAX3232ECPE+?
The MAX3232ECPE+ operates from a 3.0V to 5.5V supply. According to the Analog Devices MAX3232 product page, the family is designed for low-power operation from a single low-voltage rail, while the internal charge-pump circuit generates the bipolar voltage levels required by RS-232 transmitters. This makes the device suitable for modern 3.3V and 5V systems that must communicate with conventional RS-232 equipment.
What is the maximum data rate of MAX3232ECPE+?
The MAX3232ECPE+ supports RS-232 operation up to 1Mbps. Analog Devices specifies the MAX3232 family as a true RS-232 transceiver with operation up to 1Mbps, allowing the device to serve both conventional asynchronous serial ports and higher-speed industrial or instrument-control links. Actual usable distance and signal integrity depend on cable characteristics, baud rate, grounding, connector quality, and the surrounding circuit.
Does MAX3232ECPE+ have ESD protection?
Yes, the MAX3232ECPE+ provides ±15kV ESD protection on the RS-232 connection pins. The manufacturer describes the MAX3232E family as including enhanced electrostatic-discharge protection for the serial-port connection pins, including ground. ESD protection is intended to improve transient immunity, but it does not eliminate the need for good connector placement, grounding, shielding, and system-level surge protection.
What are the key specifications of MAX3232ECPE+ that engineers should know?
The MAX3232ECPE+ is a 16-pin PDIP dual RS-232 transceiver with two drivers, two receivers, a 3.0V to 5.5V supply range, operation up to 1Mbps, and ±15kV ESD protection. According to the Analog Devices MAX3232 product page, it uses an integrated dual charge-pump circuit to support true RS-232 signal levels from a single low-voltage supply. The package is through-hole, making it especially useful for legacy and industrial equipment.
Where can I download the MAX3232ECPE+ datasheet PDF?
The official MAX3232 datasheet is available through the Analog Devices product page at https://www.analog.com/en/products/max3232.html. The manufacturer page identifies the current data-sheet revision and provides the MAX3232 family documentation. Search for MAX3232ECPE+ on that page to review the electrical characteristics, truth tables, charge-pump capacitor recommendations, ESD information, and the complete 16-pin PDIP pin description.
Where can I find the MAX3232ECPE+ pinout?
The MAX3232ECPE+ pinout is documented in the pin-description section of the manufacturer MAX3232 data sheet. The device uses a 16-pin PDIP package, with the complete pin numbering and signal assignments available in the official Analog Devices documentation. Use the package drawing and pin-description table together when assigning PCB traces, particularly for the charge-pump capacitor connections and the RS-232 driver and receiver pins.
What is the difference between MAX3232ECPE+ and MAX3232CPE+?
The MAX3232ECPE+ is the E-series version with ±15kV ESD protection, while MAX3232CPE+ is the C-series variant listed with the same 16-PDIP format and dual RS-232 function. The verified listing describes MAX3232CPE+ as a 2/2 full-RS-232 transceiver, while the MAX3232ECPE+ listing identifies the E-series device. Both use a 3.0V to 5.5V supply and support operation up to 1Mbps according to the manufacturer family information.
Is MAX3232ECPE+ pin compatible with MAX3232CPE+?
The MAX3232ECPE+ and MAX3232CPE+ are listed with the same 16-PDIP package and the same 2/2 full-RS-232 transceiver configuration. Their principal documented distinction is the E-series ESD-protection specification of ±15kV, while the C-series is the lower-protection variant. Check the manufacturer pin descriptions and all electrical limits before substituting one for the other, particularly ESD requirements and application-specific system constraints.
Can MAX3232ECPE+ replace MAX3232ECPE?
The MAX3232ECPE+ and MAX3232ECPE represent the E-series 16-pin PDIP version with the plus-qualified ordering suffix. The verified product listings identify both as MAX3232E dual RS-232 transceivers with ±15kV ESD protection. The MAX3232ECPE+ can therefore be considered for an equivalent MAX3232ECPE position when the required package, temperature range, qualification, and ordering configuration are confirmed from the manufacturer documentation.
What is the best drop-in replacement for MAX3232ECPE+?
The MAX3232CPE+ is the closest same-package alternative listed for the MAX3232ECPE+, because both use a 16-PDIP 2/2 full-RS-232 transceiver configuration. The key difference is the E-series ±15kV ESD protection of the MAX3232ECPE+, compared with the C-series variant. Use the Request a Quote form on this page to confirm exact sourcing, and review the manufacturer data sheet before using it where the higher ESD rating is functionally required.
What can replace MAX3232ECPE+ in an RS-232 design?
The MAX3232CPE+ is a same-package replacement candidate because the verified listings identify it as a 16-PDIP dual full-RS-232 transceiver in the same MAX3232 family. The MAX3232ECPE+ offers the documented ±15kV ESD-protected E-series specification, so the substitution should be checked against the original design's ESD and system-protection requirements. Additional direct replacements should be qualified from the relevant manufacturer pin and parameter documentation.
When should I choose MAX3232ECPE+ over MAX3232CPE+?
Choose the MAX3232ECPE+ when the design benefits from the documented ±15kV ESD protection of the E-series version. The MAX3232CPE+ remains attractive for a conventional 16-PDIP RS-232 design where the full operating envelope matches and its protection specification is adequate. Both parts use the same broad transceiver arrangement, so the decisive factors are the complete electrical limits, ESD requirement, operating-temperature range, lifecycle status, and availability.
Is MAX3232ECPE+ suitable for industrial control and instrumentation?
The MAX3232ECPE+ is suitable for many industrial-control and instrumentation interfaces because it combines a 3.0V to 5.5V supply range, dual RS-232 channels, operation up to 1Mbps, and ±15kV ESD protection. Its 16-pin PDIP package is convenient for through-hole industrial boards and legacy equipment. Final suitability depends on the enclosure, cable length, grounding strategy, surge environment, and required operating-temperature range.
Where can I buy MAX3232ECPE+ and what is the lead time?
Use the Request a Quote form on this page to ask for current MAX3232ECPE+ availability, unit pricing, minimum order quantity, and lead time. The verified product listings show the exact MPN in 16-PDIP configuration, but they do not establish a stable customer-facing stock or lead-time commitment. A direct quote also allows packaging and shipment requirements to be confirmed against the intended application.
How much does MAX3232ECPE+ cost and is it in stock?
Current price and stock status for the MAX3232ECPE+ should be requested through the Request a Quote form on this page because commercial terms can change with quantity, packaging, and market conditions. The exact 16-PDIP part is listed in the verified distributor and manufacturer results, but those results do not provide a reliable, uniform stock commitment across channels. Use the quote request to obtain current availability, MOQ, and lead time.
How should MAX3232ECPE+ be used with a microcontroller UART?
Connect the microcontroller UART TX and RX signals to the MAX3232ECPE+ receiver and driver logic inputs, while using the other RS-232 channel pair for a second serial link when needed. The charge-pump capacitors must be connected exactly as shown in the manufacturer application circuit, and the RS-232 connector side should use the recommended protection and signal-routing arrangement. The device can operate from 3.0V to 5.5V and supports rates up to 1Mbps.

工程參考資料,適用於 MAX3232ECPE+ — 比較、設計指引及合規資訊。

選型指南

Choose the MAX3232ECPE+ for a 16-PDIP design that requires the documented ±15kV ESD protection, a 3.0V to 5.5V supply, and RS-232 operation up to 1Mbps. It is particularly suitable for industrial, service, and legacy-equipment interfaces where cables may be connected repeatedly. The MAX3232CPE+ can be considered for the same 16-PDIP transceiver position when its protection rating meets the system requirement and the remaining electrical limits are acceptable. The MAX3232ECPE is the closest E-series ordering alternative with the same core functionality, but the plus-qualified part should be used when that qualification and ordering designation are required. For new compact surface-mount designs, MAX3232ECDR or MAX3232CDBR provide a different mechanical option and therefore are not direct PCB drop-ins for the PDIP target. Always verify pinout, temperature range, ESD requirements, and charge-pump component values before substitution.

與替代品比較

參數 本產品 MAX3232CPE+ MAX3232ECPE
Package 16-PDIP 16-PDIP 16-PDIP
Brand Analog Devices Analog Devices Analog Devices
Transceiver Configuration 2 transmitters and 2 receivers 2 transmitters and 2 receivers 2 transmitters and 2 receivers
Supply Voltage Range 3.0V to 5.5V 3.0V to 5.5V family range 3.0V to 5.5V family range
Maximum Data Rate 1Mbps 1Mbps family range 1Mbps family range
ESD Protection ±15kV C-series protection specification; detailed rating not stated in listing ±15kV
Low-Power Supply Current Down to 10nA Down to 10nA family range Down to 10nA family range
RS-232 Interface True RS-232 True RS-232 True RS-232
Mounting Type Through-hole Through-hole Through-hole
Charge Pump Dual charge-pump circuit Dual charge-pump circuit Dual charge-pump circuit

主要差異化特點

  • Documented high-level ESD protection (對比MAX3232CPE+)
  • Exact MAX3232E through-hole configuration (對比MAX3232CPE+)
  • Single low-voltage supply with integrated charge pump (對比MAX3232ECPE)

設計說明

Place the MAX3232ECPE+ charge-pump capacitors close to their designated pins and keep the associated traces short and symmetric. Route the RS-232 connector-side signals away from switching nodes and sensitive analog inputs. The connector interface should include the protection components and grounding arrangement shown in the manufacturer datasheet; good layout is particularly important when the cable leaves the enclosure.

Do not assume every MAX3232C variant has the same ESD rating as the MAX3232E variant. The MAX3232ECPE+ is specifically identified with ±15kV ESD protection, so a C-series substitution can reduce transient robustness even if the data rate and basic RS-232 function match. Verify pin assignments, ESD requirements, operating temperature, and qualification before approving a substitution.

Decouple the device supply close to its VCC and ground pins, and follow the manufacturer’s recommended charge-pump capacitor values and tolerances. The charge pump generates the bipolar RS-232 output levels internally, so adequate bypass and short capacitor connections are important for stable transmitter operation. Confirm that the source rail remains within 3.0V to 5.5V over temperature and transient conditions.

For higher baud rates, use the shortest practical cable, maintain a suitable signal ground, and keep the RS-232 traces away from clocks, power inductors, and switching-node copper. Although the family supports rates up to 1Mbps, achievable communication distance depends on cable type and the connected equipment’s RS-232 thresholds. Scope the actual connector-side waveform when commissioning a new system.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The manufacturer product page and verified product listings do not provide explicit compliance statements for this exact ordering code. The MAX3232 family description states that the E-series provides ±15kV ESD protection, but ESD protection is not an environmental-compliance qualification.

相關搜尋

MAX3232ECPE+ datasheet MAX3232ECPE+ pinout MAX3232ECPE+ datasheet pdf MAX3232ECPE+ equivalent MAX3232ECPE+ replacement MAX3232ECPE+ price MAX3232ECPE+ stock MAX3232ECPE+ 16-PDIP MAX3232ECPE+ RS-232 transceiver MAX3232ECPE+ vs MAX3232CPE+ Analog Devices MAX3232ECPE+ MAX3232ECPE+ industrial control MAX3232ECPE+ 1Mbps MAX3232ECPE+ ±15kV ESD

相關元件與詞彙

Analog Devices MAX3232ECPE+ MAX3232CPE+ MAX3232ECPE MAX3232ECDR MAX3232CDBR RS-232 transceiver RS-232 interface IC UART transceiver dual line driver dual line receiver dual charge pump 16-PDIP package through-hole package 3.0V to 5.5V supply 1Mbps data rate ±15kV ESD protection true RS-232 industrial control equipment data acquisition systems test and measurement equipment legacy serial equipment charge-pump capacitors
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情