MAX3488ECSA+T - 3.3V 12Mbps RS-485/RS-422 Transceiver | ADI
MPN: MAX3488ECSA+T ✓ 啟用中MAX3488ECSA+T 概覽
An RS-485/RS-422 transceiver is an interface IC that converts between single-ended logic signals and differential physical-layer signals. RS-485 supports balanced, multipoint communication over relatively long cables, while RS-422 emphasizes balanced point-to-point connections. Both standards belong to the broader wired data-communication and interface-IC hierarchy, where noise immunity, common-mode tolerance, cable termination, and signal integrity determine reliable link performance.
Key features include operation from a single 3.3 V supply, data rates up to 12 Mbps, ±15 kV ESD protection, and slew-rate-limited driver outputs. The slew-rate limitation reduces high-frequency EMI and helps limit reflections on improperly terminated cables. Each device contains one driver and one receiver, making it suitable for half-duplex RS-485 networks as well as full-duplex RS-422 links when the relevant driver and receiver pins are connected appropriately.
The MAX3488 family is positioned for industrial control, instrumentation, building automation, test equipment, and embedded communications where differential signaling is preferred over single-ended interfaces. Its low-power 3.3 V operation can simplify interfaces with modern processors and field-programmable logic. The ±15 kV protection rating improves robustness at connector-exposed bus pins, although protection ratings do not eliminate the need for correct grounding, routing, and surge-protection design.
For PCB implementation, use the manufacturer pin-description table to assign the driver input, receiver output, enable controls, differential bus terminals, supply, and ground. Place bypass capacitance close to the supply pins, route the differential pair as a tightly coupled pair, and keep bus-side traces away from sensitive digital and analog paths. External termination and biasing resistors depend on cable length, topology, node count, and whether the bus is idle.
This page organizes the electrical characteristics, package details, drop-in candidates, and application guidance needed for initial design review. It also highlights the distinctions engineers should verify before PCB release, especially enable polarity, receiver thresholds, thermal limits, cable termination, and production ordering options.
直接替換替代品,適用於 MAX3488ECSA+T — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX3488ECSA+T (相同外形與佔位) — 差異在於 Package, Supply Voltage, Driver Count, ESD Protection, Maximum Data Rate.
MAX3488EESA+T
✅ 直接替換聯絡詢價
查看資料表 →MAX3490AEGSA+T
✅ 直接替換聯絡詢價
查看資料表 →MAX3490ESA+
✅ 直接替換聯絡詢價
查看資料表 →MAX3488ECSA+T 規格
| Product Type | RS-485/RS-422 transceiver |
| 供應電壓 | 3.3 V |
| Maximum Data Rate | 12 Mbps |
| ESD Protection | ±15 kV |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Supported Standards | RS-422 and RS-485 |
| Driver Architecture | Slew-rate-limited true RS-485/RS-422 driver |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
MAX3488ECSA+T 腳位配置
| 腳位 1 | ROUT — Receiver output |
| 腳位 2 | RE — Receiver enable control |
| 腳位 3 | DE — Driver enable control |
| 腳位 4 | DI — Driver data input |
| 腳位 5 | GND — Ground |
| 腳位 6 | A/Y — Driver output and receiver input |
| 腳位 7 | B/Z — Driver output and receiver input |
| 腳位 8 | VCC — Positive supply |
典型應用
MAX3488ECSA+T 適用於 6 應用s: Industrial RS-485 Control Networks, RS-422 Point-to-Point Data Links, Building Automation and HVAC Equipment, Test and Measurement Equipment, Embedded Serial Port Expansion, Instrumentation and Sensor Networks.
Industrial RS-485 Control Networks
The MAX3488ECSA+T fits industrial controller and sensor-bus nodes that use a 3.3 V RS-485 interface. Its one-driver, one-receiver arrangement supports half-duplex communication when the driver-enable and receiver-enable controls are managed correctly. The 12 Mbps maximum data rate provides substantial link margin for typical control traffic, while ±15 kV ESD protection strengthens the interface against electrostatic discharge at connector-exposed pins. The slew-rate-limited driver also helps reduce electromagnetic interference and reflections on cables with imperfect termination.
推薦
RS-422 Point-to-Point Data Links
The MAX3488ECSA+T is suitable for full-duplex RS-422 links that need a differential driver and receiver on a 3.3 V logic rail. Its 12 Mbps capability supports high-speed instrument, test-equipment, and embedded-system connections, while the differential interface improves rejection of common-mode noise relative to a single-ended link. The ±15 kV ESD rating is especially useful when a cable reaches an external connector. Confirm the source and destination grounds, cable length, impedance, and termination strategy for the installed channel.
推薦
Building Automation and HVAC Equipment
MAX3488ECSA+T can connect a 3.3 V controller to RS-485-based building automation equipment, HVAC controllers, sensors, and remote I/O modules. The low-power 3.3 V operating point suits embedded equipment, and the 8-pin SOIC package simplifies assembly in compact controller boards. Its slew-rate-limited output reduces unwanted high-frequency energy and helps control reflections when the installed network does not provide ideal termination. At each transceiver location, apply the bus bias and termination appropriate for the topology and node count.
推薦
Test and Measurement Equipment
The MAX3488ECSA+T is useful in test instruments, automated test equipment, and laboratory interfaces that exchange measurements over RS-422 or RS-485. A maximum 12 Mbps data rate supports fast status and command traffic, and the differential receiver improves noise immunity in electrically noisy environments. The ±15 kV ESD-protected bus interface is valuable for portable equipment connected to user-accessible cables. Designers should still use chassis grounding, isolation where required, and controlled cable routing to preserve measurement accuracy.
推薦
Embedded Serial Port Expansion
MAX3488ECSA+T can add a robust differential serial port to a 3.3 V embedded controller, module, or programmable-logic design. The one-driver, one-receiver topology supports RS-485 half-duplex networks or RS-422 full-duplex communication without an external line-driver package. A 12 Mbps ceiling provides headroom beyond common low-speed field buses. The principal design constraint is firmware management of enable timing: a bus controller must prevent multiple drivers from transmitting simultaneously and should handle bus contention predictably.
推薦
Instrumentation and Sensor Networks
The MAX3488ECSA+T supports distributed instrumentation where sensors, analyzers, or remote measurement modules communicate over a balanced 3.3 V bus. Differential signaling helps reject common-mode disturbances found in industrial facilities, while ±15 kV ESD protection improves robustness at externally connected interfaces. The slew-rate-limited driver limits edge energy and can reduce reflection problems associated with imperfect cable termination. For sensor networks, calculate the bias network and termination values from the number of nodes, cable impedance, and selected standard.
推薦
推薦產品摘要
工程參考資料,適用於 MAX3488ECSA+T — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MAX3488EESA+T | MAX3490AEGSA+T | MAX3490ESA |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SOIC | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Maximum Data Rate | 12 Mbps | 12 Mbps | 12 Mbps | 12 Mbps |
| Driver and Receiver Count | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver |
| Supported Interfaces | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
主要差異化特點
- Matches the 12 Mbps headline data rate of the closest family alternatives (對比MAX3488EESA+T)
- Retains the MAX3488E family's documented slew-rate-limited operation (對比MAX3490AEGSA+T)
- Provides the documented ±15 kV ESD protection class (對比MAX3490ESA)
設計說明
Place the transceiver bypass capacitor immediately between the VCC and GND pins, with a short ground return and minimal loop area. Route the A/Y and B/Z differential pair together with consistent spacing and controlled geometry; avoid routing over split planes or unrelated high-current paths. Keep the bus-side connector and protection components close to the transceiver while maintaining isolation from sensitive analog and clock circuitry.
Determine termination and fail-safe bias from the actual topology rather than fitting resistors by default. For a conventional RS-485 multidrop network, use termination at the two physical ends and a bias network that holds the idle bus at an asserted state. For RS-422, match source and destination impedances and confirm that each cable length and data rate remain within the transmitter and receiver limits published by the manufacturer.
Do not enable the driver while another node is transmitting, because simultaneous outputs can create bus contention and excess current. In half-duplex designs, manage DE and /RE so the receiver remains available when practical and the driver is disabled between transmissions. Also verify the MAX3488E suffix, temperature grade, ESD rating, and tape-and-reel configuration before placing the production order.
The slew-rate-limited MAX3488E driver reduces radiated and reflected high-frequency energy, but it does not replace good physical-layer design. Use the shortest practical stub from the transceiver to the connector, maintain a continuous reference plane, and avoid parallel runs with switching-current traces. If edge rates or cable reflections remain problematic, revisit the cable type, termination, topology, and external protection components.
合規資訊
The device is an industrial interface IC rather than an AEC-Q100 automotive-qualified variant. No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement appears in the cited product-page excerpts.