Analog Devices

MAX349EPN+ - 8:1 Low-Voltage MUX | Analog Devices

MPN: MAX349EPN+ ✓ 啟用中
+2.7 V to +16 V Vdss 100 pA Id 100 ohm Rds(on) 18-pin DIP (PDIP) Package
MOQ: 1 |

MAX349EPN+ 概覽

Analog Devices MAX349EPN+ is a serially controlled, low-voltage 8-channel multiplexer with a maximum on-resistance of 100 ohm, packaged in an 18-pin DIP. It supports dual 4-channel multiplexing, bidirectional signal conduction, break-before-make switching, and a fail-safe disconnect function. Its operating temperature range is -40°C to +85°C, while the stated supply-voltage limits cover +2.7 V to +16 V and -8 V to -2.7 V.

An analog multiplexer is an interface IC that connects multiple signal paths to a shared output through digitally controlled switches. The MAX349 belongs to the analog-switch and multiplexer hierarchy within interface semiconductors. By selecting one of eight input channels for a common terminal, it reduces the number of signal lines and external routing required in data-acquisition, measurement, and control systems. The dual 4-channel architecture supports differential-style routing while retaining an 8:1 multiplexing mode.

Key characteristics include a maximum on-resistance of 100 ohm, 300 ns and 400 ns stated switching-time figures, 8 pF channel capacitance, and 100 pA off leakage. The MAX349EPN+ is specified for both positive and negative supply rails. Positive operation extends from +2.7 V to +16 V, while negative operation extends from -8 V to -2.7 V. Its bidirectional analog channels allow signals to pass in either direction, making the device suitable for routed analog buses rather than only one-way output selection.

The serially controlled interface reduces the number of control traces required compared with a conventional parallel-address multiplexer. Its 18-PDIP package has a stated 7.62 mm body width and is compatible with through-hole assembly. Because each selected channel contributes resistance and capacitance, the device is best suited to low- and moderate-frequency analog signals where switching time and on-resistance are compatible with the measurement bandwidth. The MAX349EPN+ also specifies break-before-make operation and fail-safe disconnect behavior for controlled signal routing.

Typical uses include multiplexed sensor acquisition, laboratory measurement interfaces, industrial control signal routing, communication-channel selection, and compact test systems that must route several analog inputs through a shared conversion or processing chain. The -40°C to +85°C range supports industrial-temperature equipment, while the lead-free-compatible DIP format suits through-hole prototypes and legacy-style controller boards.

Designers should account for the 100 ohm maximum channel resistance, 8 pF capacitance, and stated switching times when setting source impedance, bandwidth, settling time, and gain expectations. Confirm signal amplitudes against the positive or negative supply rails, and use the manufacturer pin-description table when assigning PCB nets and connector routing.

This page combines the MAX349EPN+ operating limits, package details, verified drop-in comparison, application guidance, and PCB-focused design notes to support component selection and implementation. It also distinguishes the electrically similar MAX349CPN+ temperature option from a true cross-brand replacement.

直接替換替代品,適用於 MAX349EPN+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

MAX349CPN+

✅ 直接替換
📦 18-PDIP
Same 18-pin DIP footprint, 8-channel multiplexing, and 100 ohm maximum on-resistance; the operating-temperature grade differs, with MAX349EPN+ specified from -40°C to +85°C

📋 參考替代品(不在目錄中)

MAX349EPN+ 規格

Multiplexer Configuration 8:1
Number of Circuits 1 circuit
Dual Mode Configuration Dual 4:1
Maximum On-Resistance 100 ohm
Positive Supply Voltage Range +2.7 V to +16 V
Negative Supply Voltage Range -8 V to -2.7 V
工作溫度範圍 -40°C to +85°C
Channel Capacitance 8 pF
Off Leakage Current 100 pA
Stated Switching Time 300 ns
Additional Stated Switching Time 400 ns
Signal Conduction Bidirectional
Switching Sequence Break-before-make
Disconnect Feature Fail-safe disconnect
Control Interface Serial control
封裝 18-pin DIP (PDIP)
Package Body Width 7.62 mm
RoHS 狀態 Compliant

MAX349EPN+ 7.62 mm 腳位配置指南

MAX349EPN+(7.62 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

MAX349EPN+ 的 7.62 mm 封裝腳位圖

無詳細腳位定義資料: MAX349EPN+.

請參閱 資料表 以查看完整腳位配置。

典型應用

MAX349EPN+ 適用於 6 應用s: Multiplexed Sensor Acquisition, Laboratory Data Acquisition, Industrial Signal Routing, Communication Channel Selection, Test and Measurement Interfaces, Control Signal Multiplexing.

🧩

Multiplexed Sensor Acquisition

The MAX349EPN+ can route up to eight sensor signals through a shared analog measurement channel when the system uses the 8:1 configuration. Its 100 ohm maximum on-resistance is manageable for many moderate-impedance sensors, while the 8 pF channel capacitance affects source loading and settling behavior. Use the dual 4-channel mode when paired or complementary sensor outputs are more convenient. The -40°C to +85°C operating range supports industrial measurement equipment, and the 18-PDIP format simplifies through-hole assembly.

🖥️

Laboratory Data Acquisition

The MAX349EPN+ is useful in laboratory acquisition systems that must share one analog input among several sensors or conditioned channels. Its serial control architecture reduces the number of address traces required on a controller board, while the bidirectional channels support flexible signal routing. The 300 ns and 400 ns stated switching figures, combined with 8 pF capacitance, must be included in the acquisition settling plan. The -40°C to +85°C rating also allows use in temperature-controlled test equipment.

🏭

Industrial Signal Routing

The MAX349EPN+ can route low-level analog signals among measurement and control sections within industrial equipment. Its 8:1 structure is valuable where a shared input must connect to multiple sensor lines, while the dual 4-channel arrangement supports grouped routing. Positive operation from +2.7 V to +16 V and negative operation from -8 V to -2.7 V provide flexibility across common signal domains. Engineers should verify common-mode limits and the 100 ohm maximum on-resistance against their amplifier input network.

🌐

Communication Channel Selection

The MAX349EPN+ can select one of eight low-frequency analog channels for a communication or line-interface subsystem. Bidirectional conduction permits use where the selected path must carry traffic in either direction, and serial control limits the required control-bus wiring. The device is best matched to low-to-moderate-bandwidth signals because its 100 ohm maximum channel resistance and 8 pF capacitance can attenuate or slow higher-rate nodes. Verify logic levels, signal amplitude, and switching timing before assigning it to a data path.

🔧

Test and Measurement Interfaces

The MAX349EPN+ fits test-interface boards that distribute several conditioned analog inputs to a shared measuring channel. Serial control allows the instrument controller to select routes without consuming a large parallel address bus. Its -40°C to +85°C range supports commercial and industrial test environments, and the through-hole 18-pin package is convenient for prototype instrumentation. For accuracy-sensitive measurements, account for the 100 ohm maximum on-resistance and include the 8 pF capacitance when choosing source impedance and amplifier settling time.

⚡

Control Signal Multiplexing

The MAX349EPN+ can consolidate multiple low-level control or feedback signals into one routed channel in an embedded control system. The 8:1 mode increases routing flexibility, while dual 4-channel operation can organize paired signal groups. Because the channels are bidirectional and support break-before-make operation, the device is appropriate for controlled bus sharing. The serial-control requirement needs a suitable host interface and correct timing, and the selected signal amplitude must remain compatible with the chosen positive or negative supply rails.

推薦產品摘要

MAX349EPN Same MAX349 family and 18-PDIP device configuration 用於: Multiplexed Sensor Acquisition, Laboratory Data Acquisition, Industrial Signal Routing, Communication Channel Selection, Test and Measurement Interfaces, Control Signal Multiplexing MAX349CPN+ Close 18-PDIP multiplexer alternative with a different temperature grade 用於: Multiplexed Sensor Acquisition, Laboratory Data Acquisition, Industrial Signal Routing, Communication Channel Selection, Test and Measurement Interfaces, Control Signal Multiplexing
What is the MAX349EPN+?
The MAX349EPN+ is a serially controlled, low-voltage analog multiplexer with one 8:1 circuit and a dual 4-channel configuration. According to the manufacturer datasheet, it provides eight bidirectional channels, a maximum on-resistance of 100 ohm, and operation from +2.7 V to +16 V or -8 V to -2.7 V. The device is housed in an 18-pin DIP package and is intended for multiplexed analog signal routing.
What are the key specifications of MAX349EPN+ that engineers should know?
The MAX349EPN+ combines an 8:1 or dual 4-channel architecture with 100 ohm maximum on-resistance and bidirectional analog channels. Its documented operating ranges include +2.7 V to +16 V, -8 V to -2.7 V, and -40°C to +85°C. Additional characteristics include 8 pF channel capacitance, 100 pA off leakage, 300 ns and 400 ns stated switching-time figures, break-before-make operation, and an 18-PDIP package.
What is the on-resistance of MAX349EPN+?
The MAX349EPN+ has a maximum on-resistance of 100 ohm. This figure applies to each selected analog path and should be included when calculating signal attenuation, especially with a high-impedance measurement circuit. The manufacturer datasheet also identifies the device as a low-voltage CMOS multiplexer with bidirectional channels, so the effective source impedance can add directly to the 100 ohm channel resistance.
What supply voltage range does MAX349EPN+ support?
The MAX349EPN+ supports a positive supply range of +2.7 V to +16 V and a negative supply range of -8 V to -2.7 V. These operating limits allow the multiplexer to route signals referenced to positive or negative rails. Keep all connected analog voltages within the applicable supply domain and include the channel resistance and switching transient when evaluating signal margin.
Where can I download the MAX349EPN+ datasheet PDF?
The MAX349EPN+ datasheet can be opened through the Maxim Integrated PDF landing page listed in the data sources for this product. The manufacturer document identifies the device as a serially controlled, low-voltage 8-channel or dual 4-channel multiplexer. Use the pin-description table and electrical-characteristics section when assigning connector nets, selecting interface levels, and confirming switching behavior.
Where can I find the MAX349EPN+ pinout?
The MAX349EPN+ uses an 18-pin DIP package, but a pin-number-to-signal table is not reproduced on this product page. Use the manufacturer datasheet pin-description table when assigning PCB traces. The documented package is 18-PDIP with a stated 7.62 mm body width, and the device includes a serial control interface, common analog terminals, supply connections, and analog signal pins.
MAX349EPN+ vs MAX349CPN+ - which is better for industrial equipment?
The MAX349EPN+ is the better choice when the design must operate across the documented -40°C to +85°C range. The MAX349CPN+ is an electrically similar 18-pin DIP alternative, but its full operating-temperature specification must be checked in its datasheet. Both use the same 8:1 low-voltage multiplexer format and have a documented maximum on-resistance of 100 ohm.
What is the difference between MAX349EPN+ and MAX349CPN+?
The principal documented distinction is the operating-temperature grade: MAX349EPN+ is specified from -40°C to +85°C, while the MAX349CPN+ requires its own temperature limits to be checked before substitution. The comparison data identifies both as 8-channel multiplexers in 18-pin DIP packages with 100 ohm maximum on-resistance. Confirm control timing, supply limits, and every pin assignment before approving a replacement.
When should I choose MAX349EPN+ over MAX349CPN+?
Choose MAX349EPN+ when the multiplexer must operate from -40°C to +85°C, as specified for the target device. Choose MAX349CPN+ only when its documented temperature range, control timing, and supply characteristics satisfy the application. Because both devices use an 18-pin DIP format, the package alone is not enough to establish interchangeability; verify the complete pin description and operating limits.
Is MAX349EPN+ suitable for multiplexed sensor acquisition?
The MAX349EPN+ is suitable for low- and moderate-bandwidth sensor-acquisition systems that use an 8:1 or dual 4-channel arrangement. Its 100 ohm maximum on-resistance, 8 pF capacitance, and stated 300 ns and 400 ns switching-time figures must be included in the settling-time and signal-loss budget. Bias the sensor output appropriately and verify the common-mode range against the selected supply configuration.
What can replace MAX349EPN+?
The MAX349CPN+ is the clearest drop-in candidate because it is listed as an 18-pin DIP, 8-channel, 100 ohm multiplexer. Its temperature grade differs from the -40°C to +85°C MAX349EPN+ specification, so it should be selected only where its own limits are acceptable. No verified cross-brand, same-package equivalent was identified, and a general cross-reference tool should not be treated as proof of pin compatibility.
Can MAX349CPN+ replace MAX349EPN+ without a PCB change?
The MAX349CPN+ can use the same 18-pin DIP footprint, but a PCB change is not the only qualification requirement. Verify pin functions, serial-control timing, supply ranges, switching characteristics, and temperature grade against the manufacturer datasheets before production use. Its 8-channel, 100 ohm characteristics make it a close electrical match, while the temperature specification is the key distinction from MAX349EPN+.
Where can I buy MAX349EPN+ and check its lead time?
Use the Request a Quote form on this page to ask about MAX349EPN+ availability, current lead time, and order handling. The Request a Quote form is the appropriate channel for a quotation without relying on stale catalog pricing. For engineering planning, confirm the 18-PDIP package, -40°C to +85°C operating range, and lead-free ordering designation before releasing the production BOM.
What is the price of MAX349EPN+?
Use the Request a Quote form on this page for the current MAX349EPN+ quotation because catalog prices and availability change with market conditions and order quantity. The form allows the exact 18-PDIP orderable MPN, MAX349EPN+, to be included in the request. Engineers should also verify the -40°C to +85°C temperature grade and required production quantity before placing the order.
Is MAX349EPN+ in stock and what is the lead time?
Current stock and lead time for MAX349EPN+ should be requested through the Request a Quote form on this page. State the required quantity, date code requirements, and whether full tubes are acceptable. The product is an 18-pin DIP device rated from -40°C to +85°C, so procurement should avoid unqualified substitutions that may not preserve its temperature coverage.
Is there a cross-brand drop-in equivalent for MAX349EPN+?
No verified cross-brand drop-in equivalent was identified for the MAX349EPN+. A true replacement would need the same 18-pin DIP footprint, compatible serial-control interface, comparable 8-channel multiplexing, and equivalent electrical and timing behavior. The closest documented candidate is the MAX349CPN+ from the same manufacturer; it should be qualified against the original requirements rather than assumed to be interchangeable.

工程參考資料,適用於 MAX349EPN+ — 比較、設計指引及合規資訊。

選型指南

Choose MAX349EPN+ when the design requires a serially controlled 8:1 or dual 4-channel analog multiplexer in an 18-pin DIP package and must operate from -40°C to +85°C. Its 100 ohm maximum on-resistance, 8 pF capacitance, and stated switching figures make it most appropriate for low- and moderate-bandwidth signals rather than high-impedance precision paths without careful settling analysis. The MAX349CPN+ is the closest documented drop-in candidate because it shares the 18-pin DIP package and core 8-channel, 100 ohm characteristics; select it when its temperature grade and timing specifications meet the application. No verified cross-brand same-package equivalent was identified. Before approving any substitution, compare the complete pin descriptions, serial-control timing, supply configuration, channel capacitance, leakage, and operating-temperature limits rather than relying on package type alone.

與替代品比較

參數 本產品 MAX349CPN+
Brand Analog Devices Analog Devices
Package 18-PDIP 18-pin DIP
Multiplexer Configuration 8:1 / dual 4:1 8-channel / dual 4-channel
Maximum On-Resistance 100 ohm 100 ohm maximum
Signal Conduction Bidirectional Bidirectional
Control Interface Serial control Serial control

主要差異化特點

  • Extended industrial temperature specification (對比MAX349CPN+)
  • Matching 18-pin DIP footprint (對比MAX349CPN+)
  • Dual 8:1 and 4:1 channel organization (對比MAX349CPN+)

設計說明

Include the 100 ohm maximum channel resistance in the signal-path budget and ensure the downstream amplifier or converter presents sufficient input impedance. The 8 pF channel capacitance can create an RC settling penalty with high source resistance. For a repeated channel scan, allow the 300 ns and 400 ns stated switching figures to settle before sampling the selected channel.

Use the manufacturer pin-description table to assign the serial-control, common-terminal, supply, and analog-channel nets because a 18-pin DIP footprint alone does not confirm every function. Keep analog traces away from clock and control routing where possible, provide local supply bypassing according to the manufacturer layout guidance, and route each analog path consistently to minimize coupling and crosstalk.

Choose either the +2.7 V to +16 V positive operating domain or the -8 V to -2.7 V negative operating domain as required by the routed signals. Do not assume that both supply ranges apply simultaneously to one operating configuration. Check signal amplitude, control-logic levels, and absolute maximum limits against the manufacturer electrical-characteristics tables before energizing the device.

Do not substitute the MAX349CPN+ without reviewing its temperature grade and complete timing specifications. Although both devices use an 18-pin DIP format, the MAX349EPN+ is specified for -40°C to +85°C. Also avoid assuming that a generic multiplexer with the same pin count is interchangeable; the serial-control timing, common terminals, supply arrangement, and analog-channel behavior must all match.

合規資訊

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

RoHS compliance is identified for MAX349EPN+. The automotive qualification, REACH, halogen-free, lead-free, and conflict-minerals statuses are not stated in the cited product information.

資料驗證日期: 2026-11-14 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

MAX349EPN+ datasheet MAX349EPN+ pinout MAX349EPN+ datasheet pdf MAX349EPN+ equivalent MAX349EPN+ replacement MAX349EPN+ cross reference MAX349EPN+ vs MAX349CPN+ MAX349EPN+ 18-DIP multiplexer MAX349EPN+ 8:1 analog mux Analog Devices MAX349EPN+ MAX349EPN+ price MAX349EPN+ stock

相關元件與詞彙

Analog Devices MAX349EPN+ MAX349EPN MAX349CPN+ analog multiplexer analog switch interface IC semiconductor 8:1 multiplexer dual 4:1 multiplexer serial control bidirectional analog channel break-before-make fail-safe disconnect on-resistance channel capacitance off leakage 18-PDIP DIP package through-hole package RoHS industrial electronics data acquisition signal routing
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情