MAX349EPN+ - 8:1 Low-Voltage MUX | Analog Devices
料号: MAX349EPN+ ✓ 量产中MAX349EPN+ 概述
An analog multiplexer is an interface IC that connects multiple signal paths to a shared output through digitally controlled switches. The MAX349 belongs to the analog-switch and multiplexer hierarchy within interface semiconductors. By selecting one of eight input channels for a common terminal, it reduces the number of signal lines and external routing required in data-acquisition, measurement, and control systems. The dual 4-channel architecture supports differential-style routing while retaining an 8:1 multiplexing mode.
Key characteristics include a maximum on-resistance of 100 ohm, 300 ns and 400 ns stated switching-time figures, 8 pF channel capacitance, and 100 pA off leakage. The MAX349EPN+ is specified for both positive and negative supply rails. Positive operation extends from +2.7 V to +16 V, while negative operation extends from -8 V to -2.7 V. Its bidirectional analog channels allow signals to pass in either direction, making the device suitable for routed analog buses rather than only one-way output selection.
The serially controlled interface reduces the number of control traces required compared with a conventional parallel-address multiplexer. Its 18-PDIP package has a stated 7.62 mm body width and is compatible with through-hole assembly. Because each selected channel contributes resistance and capacitance, the device is best suited to low- and moderate-frequency analog signals where switching time and on-resistance are compatible with the measurement bandwidth. The MAX349EPN+ also specifies break-before-make operation and fail-safe disconnect behavior for controlled signal routing.
Typical uses include multiplexed sensor acquisition, laboratory measurement interfaces, industrial control signal routing, communication-channel selection, and compact test systems that must route several analog inputs through a shared conversion or processing chain. The -40°C to +85°C range supports industrial-temperature equipment, while the lead-free-compatible DIP format suits through-hole prototypes and legacy-style controller boards.
Designers should account for the 100 ohm maximum channel resistance, 8 pF capacitance, and stated switching times when setting source impedance, bandwidth, settling time, and gain expectations. Confirm signal amplitudes against the positive or negative supply rails, and use the manufacturer pin-description table when assigning PCB nets and connector routing.
This page combines the MAX349EPN+ operating limits, package details, verified drop-in comparison, application guidance, and PCB-focused design notes to support component selection and implementation. It also distinguishes the electrically similar MAX349CPN+ temperature option from a true cross-brand replacement.
直接替换替代料: MAX349EPN+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MAX349CPN+
✅ 直接替换📋 参考替代料(不在目录中)
MAX349EPN+ 规格参数
| Multiplexer Configuration | 8:1 |
| Number of Circuits | 1 circuit |
| Dual Mode Configuration | Dual 4:1 |
| Maximum On-Resistance | 100 ohm |
| Positive Supply Voltage Range | +2.7 V to +16 V |
| Negative Supply Voltage Range | -8 V to -2.7 V |
| 工作温度范围 | -40°C to +85°C |
| Channel Capacitance | 8 pF |
| Off Leakage Current | 100 pA |
| Stated Switching Time | 300 ns |
| Additional Stated Switching Time | 400 ns |
| Signal Conduction | Bidirectional |
| Switching Sequence | Break-before-make |
| Disconnect Feature | Fail-safe disconnect |
| Control Interface | Serial control |
| 封装 | 18-pin DIP (PDIP) |
| Package Body Width | 7.62 mm |
| RoHS 状态 | Compliant |
MAX349EPN+ 7.62 mm 引脚配置指南
MAX349EPN+(7.62 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX349EPN+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX349EPN+ 适用于 6 应用s: Multiplexed Sensor Acquisition, Laboratory Data Acquisition, Industrial Signal Routing, Communication Channel Selection, Test and Measurement Interfaces, Control Signal Multiplexing.
Multiplexed Sensor Acquisition
The MAX349EPN+ can route up to eight sensor signals through a shared analog measurement channel when the system uses the 8:1 configuration. Its 100 ohm maximum on-resistance is manageable for many moderate-impedance sensors, while the 8 pF channel capacitance affects source loading and settling behavior. Use the dual 4-channel mode when paired or complementary sensor outputs are more convenient. The -40°C to +85°C operating range supports industrial measurement equipment, and the 18-PDIP format simplifies through-hole assembly.
推荐
Laboratory Data Acquisition
The MAX349EPN+ is useful in laboratory acquisition systems that must share one analog input among several sensors or conditioned channels. Its serial control architecture reduces the number of address traces required on a controller board, while the bidirectional channels support flexible signal routing. The 300 ns and 400 ns stated switching figures, combined with 8 pF capacitance, must be included in the acquisition settling plan. The -40°C to +85°C rating also allows use in temperature-controlled test equipment.
推荐
Industrial Signal Routing
The MAX349EPN+ can route low-level analog signals among measurement and control sections within industrial equipment. Its 8:1 structure is valuable where a shared input must connect to multiple sensor lines, while the dual 4-channel arrangement supports grouped routing. Positive operation from +2.7 V to +16 V and negative operation from -8 V to -2.7 V provide flexibility across common signal domains. Engineers should verify common-mode limits and the 100 ohm maximum on-resistance against their amplifier input network.
推荐
Communication Channel Selection
The MAX349EPN+ can select one of eight low-frequency analog channels for a communication or line-interface subsystem. Bidirectional conduction permits use where the selected path must carry traffic in either direction, and serial control limits the required control-bus wiring. The device is best matched to low-to-moderate-bandwidth signals because its 100 ohm maximum channel resistance and 8 pF capacitance can attenuate or slow higher-rate nodes. Verify logic levels, signal amplitude, and switching timing before assigning it to a data path.
推荐
Test and Measurement Interfaces
The MAX349EPN+ fits test-interface boards that distribute several conditioned analog inputs to a shared measuring channel. Serial control allows the instrument controller to select routes without consuming a large parallel address bus. Its -40°C to +85°C range supports commercial and industrial test environments, and the through-hole 18-pin package is convenient for prototype instrumentation. For accuracy-sensitive measurements, account for the 100 ohm maximum on-resistance and include the 8 pF capacitance when choosing source impedance and amplifier settling time.
推荐
Control Signal Multiplexing
The MAX349EPN+ can consolidate multiple low-level control or feedback signals into one routed channel in an embedded control system. The 8:1 mode increases routing flexibility, while dual 4-channel operation can organize paired signal groups. Because the channels are bidirectional and support break-before-make operation, the device is appropriate for controlled bus sharing. The serial-control requirement needs a suitable host interface and correct timing, and the selected signal amplitude must remain compatible with the chosen positive or negative supply rails.
推荐
推荐产品汇总
工程参考数据: MAX349EPN+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX349CPN+ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 18-PDIP | 18-pin DIP |
| Multiplexer Configuration | 8:1 / dual 4:1 | 8-channel / dual 4-channel |
| Maximum On-Resistance | 100 ohm | 100 ohm maximum |
| Signal Conduction | Bidirectional | Bidirectional |
| Control Interface | Serial control | Serial control |
关键差异点
- Extended industrial temperature specification (对比 MAX349CPN+)
- Matching 18-pin DIP footprint (对比 MAX349CPN+)
- Dual 8:1 and 4:1 channel organization (对比 MAX349CPN+)
设计说明
Include the 100 ohm maximum channel resistance in the signal-path budget and ensure the downstream amplifier or converter presents sufficient input impedance. The 8 pF channel capacitance can create an RC settling penalty with high source resistance. For a repeated channel scan, allow the 300 ns and 400 ns stated switching figures to settle before sampling the selected channel.
Use the manufacturer pin-description table to assign the serial-control, common-terminal, supply, and analog-channel nets because a 18-pin DIP footprint alone does not confirm every function. Keep analog traces away from clock and control routing where possible, provide local supply bypassing according to the manufacturer layout guidance, and route each analog path consistently to minimize coupling and crosstalk.
Choose either the +2.7 V to +16 V positive operating domain or the -8 V to -2.7 V negative operating domain as required by the routed signals. Do not assume that both supply ranges apply simultaneously to one operating configuration. Check signal amplitude, control-logic levels, and absolute maximum limits against the manufacturer electrical-characteristics tables before energizing the device.
Do not substitute the MAX349CPN+ without reviewing its temperature grade and complete timing specifications. Although both devices use an 18-pin DIP format, the MAX349EPN+ is specified for -40°C to +85°C. Also avoid assuming that a generic multiplexer with the same pin count is interchangeable; the serial-control timing, common terminals, supply arrangement, and analog-channel behavior must all match.
合规信息
RoHS compliance is identified for MAX349EPN+. The automotive qualification, REACH, halogen-free, lead-free, and conflict-minerals statuses are not stated in the cited product information.