MC14016BD - 4-Channel 400Ω Analog Switch | onsemi | Signal Control
MPN: MC14016BD ✓ 啟用中MC14016BD 概覽
A CMOS analog switch is a voltage-controlled semiconductor device that connects or isolates signal paths with low on-state resistance and high off-state impedance. The MC14016B family belongs to the analog switch and multiplexer hierarchy within interface ICs. Four physically independent switches permit one control signal to route each of four signal channels, while the bidirectional construction allows signal flow in either direction when the corresponding switch is enabled.
The monolithic MC14016BD combines P-channel and N-channel MOS enhancement-mode devices. Its principal advantages include a 1:1 multiplexing configuration, four independent switch sections, operation across a 3 V to 18 V supply range, and a compact 14-pin SOIC package. Because the switches can handle analog as well as digital signals, the device is useful when a system must route sampled, sensed, or conditioned signals without permanently connecting every channel to the same bus.
Signal integrity depends on control timing, output loading, switch charge injection, and the impedance of the connected source. The 400 Ω on resistance is appropriate for moderate-impedance switching rather than low-loss RF distribution. Control inputs should be driven only when signal levels remain within the device's valid input and output ranges, and unused control and signal pins should be connected according to the manufacturer's recommended application information.
Typical uses include analog signal gating, frequency choppers, modulators and demodulators, multiplexed measurement paths, and CMOS logic interfaces. The part is especially relevant to industrial control, instrumentation, sensor multiplexing, and communication circuitry where several low-frequency or moderate-frequency signals must be selected by logic control.
For PCB design, place the device close to the signals it routes and keep return paths continuous to reduce coupling between adjacent channels. Decoupling capacitors should be placed at the power pins according to the manufacturer datasheet, and control traces should be routed away from sensitive analog inputs. This page combines the manufacturer specifications with application guidance, package details, sourcing information, and drop-in replacement considerations for faster engineering review.
直接替換替代品,適用於 MC14016BD — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MC14066B
✅ 直接替換📋 參考替代品(不在目錄中)
CD4016B
✅ 直接替換📋 參考替代品(不在目錄中)
CD4066B
✅ 直接替換📋 參考替代品(不在目錄中)
HC4016
✅ 直接替換📋 參考替代品(不在目錄中)
MC14016BFELG
✅ 直接替換📋 參考替代品(不在目錄中)
MC14016BD 最大額定值與電氣特性
| Product Type | Quad analog switch / quad multiplexer |
| Number of Switch Circuits | 4 circuits |
| Multiplexer Configuration | 1:1 |
| On-State Resistance | 400 Ω |
| Supply Voltage Range | 3 V to 18 V |
| Switch Type | Bilateral CMOS analog switch |
| Switch Architecture | P-channel and N-channel MOS enhancement-mode devices |
| Signal Routing | 1:1 |
| 腳位數 | 14 pins |
| 封裝 | 14-pin SOIC |
| 安裝類型 | Surface mount |
| Signal Type | Analog or digital |
| Input ESD Protection | Not provided on inputs and outputs |
MC14016BD 腳位配置
| 腳位 1 | OUT A — Common terminal for switch A |
| 腳位 2 | IN A — Normally closed terminal for switch A |
| 腳位 3 | IN B — Normally closed terminal for switch B |
| 腳位 4 | OUT B — Common terminal for switch B |
| 腳位 5 | OUT C — Common terminal for switch C |
| 腳位 6 | IN C — Normally closed terminal for switch C |
| 腳位 7 | IN D — Normally closed terminal for switch D |
| 腳位 8 | OUT D — Common terminal for switch D |
| 腳位 9 | CONTROL D — Control input for switch D |
| 腳位 10 | CONTROL C — Control input for switch C |
| 腳位 11 | CONTROL B — Control input for switch B |
| 腳位 12 | CONTROL A — Control input for switch A |
| 腳位 13 | VSS — Negative supply terminal |
| 腳位 14 | VDD — Positive supply terminal |
典型應用
MC14016BD 適用於 6 應用s: Analog Sensor Channel Multiplexing, Signal Gating and Instrumentation, Chopper and Modulator Circuits, Industrial Control Signal Routing, CMOS Logic Interface and Signal Isolation, Test and Measurement Signal Selection.
Analog Sensor Channel Multiplexing
The MC14016BD suits multiplexed sensor acquisition because its four independent bilateral switches can select analog or digital signals while the stated on-state resistance is 400 Ω. Place the device close to the sensor interface and account for that resistance when sizing buffers and converters. The 1:1 architecture supports four channels without sharing a switching node, while the 3 V to 18 V supply range permits operation from low-voltage sensor systems through conventional CMOS control rails.
推薦
Signal Gating and Instrumentation
MC14016BD can gate up to four moderate-impedance signals in front of an instrumentation amplifier, measurement amplifier, or data-conversion input. Its bilateral construction supports controlled signal paths for calibration, range selection, or isolation of inactive inputs. Because the on-state resistance is 400 Ω, design the source impedance so the switch does not dominate measurement accuracy, and evaluate control transients for sensitive high-impedance nodes.
推薦
Chopper and Modulator Circuits
The four independently controlled switches in MC14016BD can form the switching elements of chopper, modulator, and demodulator arrangements. Each section can conduct signals in either direction, allowing the same package to support alternate current paths or phase-sensitive switching. The 400 Ω path resistance must be included in insertion-loss and impedance calculations, and clock-like control transitions should be timed so they do not overlap intended signal intervals.
推薦
Industrial Control Signal Routing
MC14016BD is applicable in industrial control systems that route low-frequency analog command or feedback signals between logic-controlled stages. Its 3 V to 18 V operating range supports multiple CMOS supply arrangements, and the 14-pin SOIC package simplifies assembly on conventional control boards. Ensure that switched signals remain within the valid common-mode range, provide defined levels to unused control inputs, and isolate long external wiring from sensitive analog routing.
推薦
CMOS Logic Interface and Signal Isolation
The MC14016BD can implement logic-controlled isolation paths for both digital and analog signals using its four bilateral switch sections. When disabled, each section provides high off-state isolation; when enabled, it provides a nominal 400 Ω connection. Design the receiving gate and driver so their input currents, voltage thresholds, and leakage remain compatible with the switch characteristics, and avoid interpreting the off condition as an infinite impedance.
推薦
Test and Measurement Signal Selection
MC14016BD can select test, reference, or calibration signals in a compact measurement front end. The four-section arrangement allows several inputs to share one downstream converter or amplifier while independent controls establish the selected route. The 400 Ω on resistance may require an input buffer for high-accuracy measurements, and charge injection should be evaluated when low-level signals are switched. Place the device near the acquisition circuitry to minimize additional parasitic capacitance.
推薦
推薦產品摘要
工程參考資料,適用於 MC14016BD — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MC14066B | CD4016B | CD4066B | HC4016 | MC14016BFELG |
|---|---|---|---|---|---|---|
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Brand | onsemi | onsemi | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Function | Quad bilateral switch / quad multiplexer | Quad bilateral switch / quad multiplexer | Quad bilateral switch | Quad bilateral switch | High-speed CMOS quad bilateral switch | Quad bilateral switch / quad multiplexer |
| Number of Switch Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Signal Type | Analog or digital | Analog or digital | Analog or digital | Analog or digital | Analog or digital | Analog or digital |
| Replacement Qualification | Primary device | Same-family option when lower on resistance is required | Manufacturer-documented pin-for-pin replacement | Manufacturer-documented pin-for-pin replacement | High-speed CMOS option | Related ordering option |
主要差異化特點
- Four independently controlled bilateral sections (對比MC14066B)
- Documented cross-family replacement path (對比CD4016B)
- Straightforward 3 V to 18 V CMOS operation (對比HC4016)
設計說明
Treat the 400 Ω on-state resistance as part of the signal path rather than as a negligible interconnect. Estimated example: a source impedance of 1 kΩ combined with 400 Ω of switch resistance creates approximately 400 Ω of total series resistance and can attenuate the signal by about 29% relative to an unloaded source. Use the actual source impedance and load in the system calculation, and add a buffer when accuracy, drive current, or impedance matching requires it.
Place the MC14016BD close to the multiplexer or acquisition node and route each switched signal with a continuous ground reference. Keep control traces away from sensitive analog nets, particularly because the manufacturer notes that improved transfer-characteristic designs can have increased parasitic coupling capacitance. Decouple VDD and VSS according to the manufacturer application guidance, and avoid long parallel routes between active and inactive switch sections.
Do not apply a signal or control voltage outside the absolute maximum and recommended operating limits. The manufacturer warns that the inputs and outputs do not include ESD protection, so use external protection and handling procedures when long cables, exposed connectors, or human-accessible circuits are involved. Also define every unused control input at a valid logic level instead of allowing it to float.
Route the four bilateral switch paths so that disabled channels cannot unintentionally couple energy into the selected channel. Maintain consistent ground connections, minimize stub lengths, and place high-impedance nodes away from control and switching edges. If switching low-level signals, evaluate charge injection and control-edge settling before defining the acquisition timing window.
合規資訊
The onsemi MC14016B datasheet states that the device inputs and outputs do not have ESD protection. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified for this ordering code.