MC14051BF 8:1 Analog Multiplexer, 280 Ohm, 16-Pin SOIC | onsemi
MPN: MC14051BF ✓ 啟用中MC14051BF 概覽
An analog multiplexer is an interface IC that routes multiple signal sources to a common output or distributes one signal among multiple destinations. The MC14051B family uses CMOS-style bilateral switches, allowing analog signals to be handled across the operating supply range. In multiplex mode, three select inputs determine which of the eight channels connects to the common terminal. In demultiplex mode, the common terminal drives the selected channel, depending on the external circuit configuration and signal direction.
The MC14051BF provides low ON impedance and very low OFF leakage current. The manufacturer describes the MC14051B, MC14052B, and MC14053B as digitally controlled analog switches, with the MC14051B implementing an SP8T solid-state switch. The low switching resistance is useful when connecting higher-impedance sensors, measurement inputs, or low-frequency control signals to a shared analog-to-digital converter or instrumentation amplifier.
Because the common and channel terminals are bilateral switch paths, the device can be used for signal multiplexing, signal distribution, and circuit isolation. The three select inputs are decoded internally to select one of eight channels. Designers should ensure that select transitions do not create unacceptable transients when the connected signals can change rapidly, and they should account for off-channel leakage and parasitic capacitance when precision measurements are required.
The MC14051BF is identified by onsemi with an operating temperature range of -55 °C to +125 °C in distributor listings and a 16-pin SO EIAJ package. The device is commonly used with 3 V, 5 V, 12 V, and 18 V supply systems. Its broad supply range and CMOS control interface make it suitable for industrial instrumentation, test and measurement, communication interfaces, audio routing, and embedded control systems.
For PCB implementation, place the device close to the multiplexed signal source and the receiving circuit to minimize trace capacitance and analog crosstalk. Keep the common and channel routing reasonably short, provide a stable supply connection, and observe the manufacturer’s input voltage limits. The select logic should be driven by compatible CMOS logic and changed only after considering the signal states present on the connected channels. This page summarizes the manufacturer’s device description, distributor specifications, package information, application considerations, and verified replacement references for MC14051BF evaluation.
直接替換替代品,適用於 MC14051BF — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MC14051BDR2G
✅ 直接替換📋 參考替代品(不在目錄中)
MC14051BDG
✅ 直接替換📋 參考替代品(不在目錄中)
MC14051BFEL
✅ 直接替換📋 參考替代品(不在目錄中)
MC14051BF 規格
| Device Type | 8:1 analog multiplexer and demultiplexer |
| Switch Configuration | SP8T |
| Number of Channels | 8 channels |
| ON Resistance | 280 ohm |
| Supply Voltage Range | 3 V to 18 V |
| Control Inputs | 3 binary select inputs |
| Signal Type | Analog or digital |
| Switch Direction | Bilateral analog switching |
| 工作溫度範圍 | -55 °C to +125 °C |
| 封裝 | 16-pin SO EIAJ |
| 安裝類型 | Surface mount |
| Technology | CMOS analog switch |
| ON Impedance | Low ON impedance |
| OFF Leakage Current | Very low OFF leakage current |
| Lead-Free Packaging | Pb-free packages available |
| Pin-for-Pin Compatibility | Pin-for-pin replacement for CD4051, CD4052, and CD4053 families |
| Data Sheet Publication Number | MC14051B/D |
MC14051BF 腳位配置
| 腳位 1 | IN3 — Analog input/output channel 3 |
| 腳位 2 | IN0 — Analog input/output channel 0 |
| 腳位 3 | IN1 — Analog input/output channel 1 |
| 腳位 4 | IN2 — Analog input/output channel 2 |
| 腳位 5 | VEE — Negative analog supply or ground reference |
| 腳位 6 | IN7 — Analog input/output channel 7 |
| 腳位 7 | IN6 — Analog input/output channel 6 |
| 腳位 8 | IN5 — Analog input/output channel 5 |
| 腳位 9 | S2 — Binary select input 2 |
| 腳位 10 | S1 — Binary select input 1 |
| 腳位 11 | S0 — Binary select input 0 |
| 腳位 12 | IN4 — Analog input/output channel 4 |
| 腳位 13 | COM — Common analog input/output terminal |
| 腳位 14 | IN8 — Analog input/output channel 8 |
| 腳位 15 | VSS — Negative digital supply or ground reference |
| 腳位 16 | VDD — Positive supply voltage |
典型應用
MC14051BF 適用於 6 應用s: Multiplexed Sensor Front End, Data Acquisition and Test Systems, Industrial Control Signal Routing, Communication Signal Multiplexing, Audio and Low-Frequency Signal Selection, Portable and Battery-Powered Instruments.
Multiplexed Sensor Front End
The MC14051BF can route up to eight sensor outputs to one common analog input, reducing the number of ADC channels required in a measurement system. Its approximately 280 ohm ON resistance is practical when sensor and amplifier impedances are substantially higher, while the 3 V to 18 V supply range supports both low-voltage and industrial systems. Place the multiplexer near the sensor inputs, use short traces, and select the channel long enough for the ADC and associated filter to settle. If source impedance approaches the switch resistance, add a high-input-impedance buffer and include the switch's contribution to gain error in the calibration.
推薦
Data Acquisition and Test Systems
MC14051BF is suitable for instrument front ends that must sample multiple inputs with one ADC or measurement amplifier. The 8:1 arrangement and three binary select controls provide a straightforward channel-selection interface, while low OFF leakage helps isolate unselected sources. Designers should budget acquisition time for switching and filtering, use a consistent reference for all channels, and account for approximately 280 ohm ON resistance in the input network. Short common-terminal routing and guarded unused channels reduce leakage and crosstalk in precision measurements.
推薦
Industrial Control Signal Routing
The MC14051BF can select among eight analog control or feedback signals in industrial equipment while operating from a 3 V to 18 V supply. Its low ON impedance makes it useful for routing signals from transducers and conditioning stages into a common controller input. The wide -55 °C to +125 °C range supports demanding industrial environments, but system designers must still control ground offsets, protect external lines from transients, and prevent select transitions from creating control glitches. Use pull resistors where a defined select state is required during reset.
推薦
Communication Signal Multiplexing
MC14051BF can route one of eight low-frequency analog or logic signals through a common channel for communication equipment with controlled timing. Its SP8T arrangement and three select inputs simplify address decoding, while the approximately 280 ohm ON resistance is suitable when line drivers and receivers use impedances well above 300 ohm. Keep the selected path short and maintain a continuous ground reference to limit coupling. For high-speed signals, verify switching time, bandwidth, charge injection, and capacitance against the manufacturer's electrical characteristics before using this device.
推薦
Audio and Low-Frequency Signal Selection
The MC14051BF can select among eight audio-band or other low-frequency sources when the source impedance is high enough that the approximately 280 ohm ON resistance causes acceptable attenuation. It is useful in source-selection circuits, test fixtures, and compact analog routing systems. Keep the common path short, maintain low ground bounce, and avoid routing signals near high-current switching nodes. If the switch resistance would create audible level loss or channel imbalance, add a low-noise buffer rather than forcing the multiplexer to drive a low-impedance load.
推薦
Portable and Battery-Powered Instruments
MC14051BF is useful in low-power portable instruments that need to monitor multiple analog channels without providing a dedicated front end for every source. Its ability to operate from a 3 V supply supports compatibility with low-voltage embedded systems, although the device is a conventional CMOS analog switch rather than a power-optimized analog switch. Evaluate leakage over the intended measurement interval and confirm whether a lower-leakage device is preferable for battery-powered electrochemical or high-impedance sensors. Firmware should also avoid changing the selected channel until prior conversions are complete.
推薦
推薦產品摘要
工程參考資料,適用於 MC14051BF — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MC14051BDR2G | MC14051BDG | MC14051BFEL |
|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi |
| Package | 16-pin SO EIAJ | 16-pin SO EIAJ | 16-pin SO EIAJ | 16-pin SO EIAJ |
| Multiplexer Configuration | 8:1 SP8T | 8:1 SP8T | 8:1 SP8T | 8:1 SP8T |
| Number of Select Inputs | 3 binary inputs | 3 binary inputs | 3 binary inputs | 3 binary inputs |
| Signal Type | Analog or digital | Analog or digital | Analog or digital | Analog or digital |
| Switch Topology | Bilateral CMOS analog switch | Bilateral CMOS analog switch | Bilateral CMOS analog switch | Bilateral CMOS analog switch |
| CD4051 Pin Compatibility | Pin-for-pin replacement family | MC14051B family | MC14051B family | MC14051B family |
主要差異化特點
- Eight-channel analog selection in a standard 16-pin package (對比MC14051BDR2G)
- Direct same-manufacturer sourcing path (對比MC14051BDG)
- Family-level compatibility with CD4051 designs (對比MC14051BFEL)
設計說明
Do not treat the 280 ohm ON resistance as negligible when the selected source has a high impedance. The switch and surrounding network form a voltage divider, and the resistor itself adds thermal noise. For precision measurements, use source and load impedances much higher than 280 ohm, or place a low-noise, high-impedance buffer after the common terminal. Also allow the ADC sample-and-hold circuit and antialiasing filter to settle after each channel change.
Route the COM terminal and the eight channel terminals with short, direct traces and maintain a continuous ground plane beneath and around the device. Avoid sharing narrow paths with switching-power nodes or digital clocks. Place any input filtering close to the pins that it protects, and use a defined select state during reset through appropriate pull resistors. These layout practices reduce parasitic capacitance, coupling, and startup transients that can affect low-level analog measurements.
Estimate the acquisition sequence as switch-selection time plus amplifier-settling time plus ADC-sampling time. The MC14051BF is suitable for many low-frequency multiplexing tasks, but its bandwidth, channel capacitance, charge injection, and switching-time characteristics must be checked before using it for fast signals. At higher frequencies, preserve impedance continuity, minimize loop area, and consider a dedicated high-speed analog switch with lower ON resistance and controlled charge injection.
Supply VDD and the analog and digital return pins according to the manufacturer datasheet, paying particular attention to VEE in systems that use split or negative analog supplies. Decouple the supply pins locally and keep the common signal ground reference continuous. Do not apply signal voltages to pins unless the complete electrical characteristic table confirms that the selected condition is valid. The listed 3 V to 18 V operating range is a device boundary, not permission to exceed absolute maximum ratings.
合規資訊
The manufacturer datasheet states that Pb-free packages are available. Separate RoHS, REACH, halogen-free, and conflict-minerals classifications were not identified in the cited product information, so those fields remain unknown. AEC-Q100 is not applicable to this general-purpose interface IC.