MC33174PG - 44V Quad Op Amp, 1.8MHz | onsemi
MPN: MC33174PG ✓ 啟用中MC33174PG 概覽
An operational amplifier is an active semiconductor device that compares two input voltages and drives its output to amplify the difference between them. A quad operational amplifier integrates four amplifiers into one package, reducing board area and simplifying multi-channel instrumentation, sensor, audio, and control designs. The MC33174 belongs to the broader operational-amplifier hierarchy, where it functions as a voltage-feedback amplifier and ultimately as a general-purpose analog signal-conditioning IC.
The MC33174PG's major benefits include its wide 3 V to 44 V supply range, low 180 µA supply current per amplifier, and 1.8 MHz gain-bandwidth product. The 2.1 V/µs slew rate supports moderate-accuracy signal transitions without the operating characteristics of a high-speed precision amplifier. A 20 nA input-bias-current specification is particularly useful in sensor interfaces and bias-resistor networks, although the complete electrical limits should be checked against the required supply voltage and common-mode range.
The device uses quality bipolar fabrication and provides four amplifiers in the MC33171/MC33172/MC33174 operating-amplifier family. Its electrical performance is intended for general-purpose applications rather than precision instrumentation. The 14-DIP package provides a conventional through-hole footprint with 7.62 mm row spacing, making it suitable for prototyping, industrial control equipment, legacy systems, and applications where a dual-inline package is easier to assemble or inspect.
Typical uses include four-channel sensor conditioning, industrial current and voltage monitoring, audio preamplification, active filtering, relay and actuator drive, laboratory instrumentation, and embedded control boards. Because it accepts supply voltages as high as 44 V, the device can also operate in higher-voltage industrial circuits when the signal common-mode voltage, output swing, and input protection remain within the device limits.
The main design consideration is the relationship among bandwidth, supply voltage, and output swing. A gain of 10 reduces the usable bandwidth to approximately 180 kHz, so higher closed-loop gains should not be selected when wider signal bandwidth is required. Decoupling capacitors should be placed close to the supply pins, unused amplifier channels should be configured in a stable non-inverting arrangement, and input and output paths should avoid excessive capacitive loading.
This product record combines the manufacturer family information, package identification, electrical characteristics, lifecycle context, sourcing workflow, and practical guidance for evaluating the MC33174PG in a new quad-amplifier design. It also distinguishes the exact MC33174PG from package and ordering-code variations so engineers can confirm footprint compatibility before replacement.
直接替換替代品,適用於 MC33174PG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MC33174PG (相同外形與佔位) — 差異在於 Amplifier Type, Gain-Bandwidth Product, Number of Pins, Package, Slew Rate.
MC33174P
✅ 直接替換📋 參考替代品(不在目錄中)
MC33174PG 最大額定值與電氣特性
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 4 channels |
| Supply Voltage Range | 3 V to 44 V |
| Gain-Bandwidth Product | 1.8 MHz |
| Slew Rate | 2.1 V/µs |
| Supply Current per Channel | 180 µA |
| Input Bias Current | 20 nA |
| 封裝 | 14-PDIP |
| Package Row Spacing | 7.62 mm |
| 安裝類型 | Through-hole |
| 腳位數 | 14 pins |
| Technology | Bipolar |
| RoHS 狀態 | RoHS-compliant |
| Lead-Free Status | Lead-free |
MC33174PG 腳位配置
| 腳位 1 | OUT 1 — Output of amplifier 1 |
| 腳位 2 | IN- 1 — Inverting input of amplifier 1 |
| 腳位 3 | IN+ 1 — Non-inverting input of amplifier 1 |
| 腳位 4 | V- — Negative supply connection |
| 腳位 5 | IN+ 2 — Non-inverting input of amplifier 2 |
| 腳位 6 | IN- 2 — Inverting input of amplifier 2 |
| 腳位 7 | OUT 2 — Output of amplifier 2 |
| 腳位 8 | OUT 3 — Output of amplifier 3 |
| 腳位 9 | IN- 3 — Inverting input of amplifier 3 |
| 腳位 10 | IN+ 3 — Non-inverting input of amplifier 3 |
| 腳位 11 | V+ — Positive supply connection |
| 腳位 12 | IN+ 4 — Non-inverting input of amplifier 4 |
| 腳位 13 | IN- 4 — Inverting input of amplifier 4 |
| 腳位 14 | OUT 4 — Output of amplifier 4 |
典型應用
MC33174PG 適用於 6 應用s: Industrial Sensor Signal Conditioning, Current and Voltage Monitoring, Audio Preamplification, Active Filtering and Control, Lab and Test Instrumentation, Legacy Through-Hole Control Boards.
Industrial Sensor Signal Conditioning
The MC33174PG suits four-channel industrial sensor-conditioning circuits because it combines four amplifiers with a 3 V to 44 V supply range and a 20 nA input-bias current. Each channel can buffer a transducer or amplify a small differential error signal without requiring a separate amplifier package. The 1.8 MHz gain-bandwidth product supports moderate-bandwidth sensing, while the 2.1 V/µs slew rate is adequate for many process-control signals. Designers should still verify sensor output voltage, common-mode range, isolation, noise, and operating temperature before deployment. Stable reference connections, local supply bypassing, and protection against industrial transients are essential around this quad amplifier.
推薦
Current and Voltage Monitoring
The four channels in the MC33174PG can monitor multiple low-level current or voltage signals when one circuit includes a shunt amplifier, one includes a precision divider, and the remaining channels support filtering or diagnostics. Its 20 nA input-bias-current characteristic helps minimize loading of high-impedance sensor networks, and its wide supply range permits operation from industrial rails up to 44 V. Gain-bandwidth becomes approximately 180 kHz at a closed-loop gain of 10, so the design must balance measurement bandwidth against noise and accuracy. Input protection, common-mode headroom, and calibrated scaling should be evaluated for each monitored signal.
推薦
Audio Preamplification
The MC33174PG can implement four general-purpose audio preamplifier or active-filter channels in analog mixer and monitoring equipment. A gain of 10 provides an estimated bandwidth of about 180 kHz from the 1.8 MHz gain-bandwidth product, while the 2.1 V/µs slew rate is suitable for moderate audio-bandwidth waveforms. Low-noise design still requires attention to resistor selection, source impedance, supply decoupling, and output loading. The single-supply range of 3 V to 44 V allows flexible rail selection, although the audio signal must remain within the amplifier's input and output limits. Four channels also reduce the number of packages needed in a multi-zone amplifier.
推薦
Active Filtering and Control
The MC33174PG is appropriate for four active-filter or analog-control sections in industrial and embedded systems. Its 1.8 MHz gain-bandwidth product provides useful loop bandwidth for audio-frequency, sensing, and slow control applications, while the 2.1 V/µs slew rate limits large-signal performance at high frequency. Designers can allocate one channel to a low-pass filter, another to an active gain stage, and the remaining channels to error amplification or actuator control. Component tolerances in the feedback network directly affect cutoff frequency and gain, so standard 1% resistors or better should be considered. Stability should be checked with the intended load capacitance and output isolation resistor.
推薦
Lab and Test Instrumentation
Four MC33174PG channels can support laboratory and test-instrument front ends that require buffered inputs, gain stages, active filters, or output drivers in a conventional through-hole package. The 3 V to 44 V supply range accommodates both low-voltage portable equipment and higher-voltage industrial fixtures, while the 180 µA per-channel supply current helps limit power demand. For precision measurements, however, the general-purpose offset and noise characteristics must be considered against the required accuracy. A quad package also simplifies channel matching and reduces wiring complexity, although analog ground and return paths should be arranged carefully to avoid injecting measurement errors.
推薦
Legacy Through-Hole Control Boards
The MC33174PG is well suited to legacy through-hole control boards where a 14-DIP footprint and conventional analog design are priorities. Its four channels can implement error amplifiers, comparators, drivers, and signal-conditioning stages without requiring multiple amplifier packages. The 7.62 mm row spacing and through-hole construction simplify hand assembly, prototype rework, and inspection compared with fine-pitch surface-mount devices. When updating an existing board, verify the exact pin functions, supply limits, and any obsolete suffix requirements before fitting. Add local bypass capacitors and input protection appropriate to the board environment, especially when the amplifier drives relays, solenoids, or long external wiring.
推薦
推薦產品摘要
工程參考資料,適用於 MC33174PG — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MC33174P | MC33174N |
|---|---|---|---|
| Package | 14-PDIP | 14-PDIP | 14-PDIP |
| Brand | onsemi | onsemi | onsemi |
| Number of Amplifiers | 4 | 4 | 4 |
| Supply Voltage Range | 3 V to 44 V | 3 V to 44 V | 3 V to 44 V |
| Gain-Bandwidth Product | 1.8 MHz | 1.8 MHz | 1.8 MHz |
| Slew Rate | 2.1 V/µs | 2.1 V/µs | 2.1 V/µs |
| Supply Current per Channel | 180 µA | 180 µA | 180 µA |
| Input Bias Current | 20 nA | 20 nA | 20 nA |
| Technology | Bipolar | Bipolar | Bipolar |
| Ordering-Suffix Qualification | PG suffix | P suffix; qualification requires confirmation | N suffix; qualification requires confirmation |
主要差異化特點
- Four general-purpose amplifiers in one through-hole package (對比MC33174P)
- Wide single-supply operating range (對比MC33174N)
- Balanced bandwidth, slew rate, and supply current (對比MC33174P)
設計說明
Place the supply bypass capacitor close to pins 11 and 4 and return its ground end directly to the board ground plane. Although the device consumes approximately 180 µA per channel, four channels can draw roughly 720 µA before output-current effects are considered. Validate the selected supply against the 3 V to 44 V range and ensure that input common-mode and output-swing requirements remain satisfied at the minimum and maximum supply voltages.
Do not assume that every amplifier can slew a large output step at its full 1.8 MHz small-signal bandwidth. The maximum practical frequency is also constrained by the 2.1 V/µs slew rate and output-current capability. For example, a 1 V full-scale output requires approximately 476 ns to slew. Check gain, signal amplitude, load current, and output-voltage headroom together rather than selecting the bandwidth specification alone.
Use the 14-pin DIP footprint with a 7.62 mm row spacing and verify the manufacturer's package drawing before layout release. Keep high-impedance input traces short, guard them against switching-node and relay-drive traces, and avoid routing output feedback loops through areas containing fast digital or switching signals. If the output drives a long cable or capacitive load, add an isolation resistor at the amplifier output to reduce oscillation risk.
An unused amplifier channel must not be left with floating inputs. Connect its output to its inverting input and its non-inverting input to a suitable reference, normally ground for a single-supply design, while confirming that the reference lies within the input common-mode range. This stable configuration minimizes offset movement, oscillation, and noise coupling into adjacent channels.
合規資訊
The exact MC33174PG listing identifies the device as RoHS-compliant and lead-free. The onsemi family page states that the MC33171/MC33172/MC33174 series is specified over industrial and automotive temperature ranges; exact AEC-Q100 qualification for the PG ordering code should be confirmed from the ordering table.