MCP3301T-CI/SN - 13-Bit 100 ksps Differential ADC | Microchip
MPN: MCP3301T-CI/SN ✓ 啟用中MCP3301T-CI/SN 概覽
An ADC is an analog-to-digital converter, a semiconductor that samples a continuous voltage and produces a corresponding digital code. The MCP3301 belongs to the data-converter IC hierarchy and specifically provides one differential input with 13-bit resolution. Differential operation means that the converter measures the voltage between two input nodes rather than measuring a single input relative to ground. This architecture is useful when the signal source is balanced or when common-mode noise must be rejected.
Key specifications include 13-bit resolution, a maximum conversion rate of 100 ksps, and a 4.5 V to 5.5 V supply range. The external reference can vary from 400 mV to 5 V, producing input-referred resolution between 98 µV and 1.22 mV. The SPI interface supports straightforward communication with microcontrollers, while the low-power characteristics suit portable instruments and distributed sensing nodes.
Internally, the MCP3301 uses a successive-approximation conversion process, charging an internal sample-and-hold capacitor before comparing the sampled voltage against its reference. The external reference defines the input range and therefore affects both conversion accuracy and code scaling. Designers must account for reference noise, input-source impedance, acquisition time, and SPI clock timing when interpreting the rated throughput.
Typical uses include battery-powered measurement equipment, industrial process monitoring, remote data acquisition, environmental sensors, and laboratory instruments. A differential sensor, current-sense amplifier, or low-level transducer can feed the ADC when its output voltage remains within the selected reference range. The converter is particularly appropriate where one analog channel is sufficient and low power consumption is more important than high channel count.
Place the reference and input networks close to the device, keep analog traces short, and provide a quiet reference source. Because the MCP3301 requires an external reference, reference stability can dominate the overall measurement accuracy. The 8-pin SOIC footprint simplifies assembly, but careful grounding and decoupling remain necessary to preserve the converter's low-noise performance.
This product page combines the core electrical characteristics, application guidance, comparison information, and practical design considerations needed to evaluate the MCP3301T-CI/SN for an SPI-based analog measurement design.
直接替換替代品,適用於 MCP3301T-CI/SN — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP3301T-CI/SN (相同外形與佔位) — 差異在於 Package, Converter Type, Digital Interface, Input Architecture, Resolution.
MCP3301T-BI/SN
✅ 直接替換聯絡詢價
查看資料表 →MCP3201T-CI/SN
✅ 直接替換📋 參考替代品(不在目錄中)
MCP3201T-BI/SN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP3201T-BI/MS
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP3301T-BI/MS
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MCP3301T-CI/SN 最大額定值與電氣特性
| 解析度 | 13 bits |
| Input Channels | 1 channel |
| Input Architecture | Fully differential input |
| Conversion Method | Successive approximation (SAR) |
| Maximum Conversion Rate | 100 ksps |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Reference Voltage Range | 400 mV to 5 V |
| Input-Referred Resolution | 98 µV to 1.22 mV |
| Digital Interface | SPI |
| 封裝 | 8-pin SOIC, 150 mil |
| 工作溫度範圍 | -40 °C to +85 °C |
| Power Consumption | Low power |
| Application Category | Battery-powered and remote data-acquisition systems |
| RoHS 狀態 | Compliant |
| Reference Implementation | External voltage reference |
| 安裝類型 | Surface mount |
| Converter Type | Single-channel ADC |
| Output Resolution | 13 bits |
MCP3301T-CI/SN 腳位配置
| 腳位 1 | CS — Chip-select input for the SPI serial interface |
| 腳位 2 | DIN — Serial data input for conversion commands |
| 腳位 3 | DOUT — Serial data output carrying the conversion result |
| 腳位 4 | VSS — Negative supply and ground connection |
| 腳位 5 | VREF+ — Positive reference-voltage input |
| 腳位 6 | VIN- — Negative differential analog input |
| 腳位 7 | VIN+ — Positive differential analog input |
| 腳位 8 | VDD — Positive supply-voltage input |
典型應用
MCP3301T-CI/SN 適用於 6 應用s: Battery-Powered Data Acquisition, Industrial Process Monitoring, Remote Environmental Sensing, Precision Current Measurement, Laboratory Instrument Front End, Portable Measurement Instrument.
Battery-Powered Data Acquisition
The MCP3301T-CI/SN fits battery-powered data-acquisition equipment because it combines a 13-bit resolution with low-power operation and a single differential analog channel. A microcontroller can initiate each conversion over SPI and read the result without operating multiple simultaneous input channels. The 4.5 V to 5.5 V supply range makes the device appropriate for regulated 5 V systems. External reference design, sensor excitation, and display or radio electronics should be evaluated separately because the ADC is only one element of the complete acquisition chain.
推薦
Industrial Process Monitoring
The MCP3301T-CI/SN is suitable for industrial process monitoring when a single low-level differential signal must be digitized close to the sensor or transmitter. Its fully differential input can accept the voltage difference between VIN+ and VIN-, reducing sensitivity to common-mode disturbance when the source is balanced. The 100 ksps maximum rate supports fast sampling, while 13-bit resolution gives more code levels than a 12-bit converter. Choose the external reference and input range to match the transducer output, and maintain the specified supply voltage.
推薦
Remote Environmental Sensing
The MCP3301T-CI/SN supports remote environmental sensing systems that measure one differential sensor signal while operating from a local 5 V supply. A bridge, thermocouple interface, or low-level pressure sensor can drive the differential inputs, and the MCU can read the 13-bit result through SPI. Low-power characteristics help manage overall instrument energy, but the external reference and sensor interface also need low-power states. Because the device has one input channel, multiplexed or simultaneous multi-channel measurement requires additional external switching or converters.
推薦
Precision Current Measurement
The MCP3301T-CI/SN can digitize the output of a current-sense amplifier when the amplifier provides a differential signal. The 13-bit resolution provides 8192 nominal code levels, while the fully differential input is well matched to shunt-amplifier outputs. The reference voltage determines the measurable span, so it should be selected without clipping normal current peaks. Input filtering, amplifier settling, and SPI timing must be coordinated to preserve accuracy at the maximum conversion rate of 100 ksps.
推薦
Laboratory Instrument Front End
The MCP3301T-CI/SN is useful in a laboratory instrument front end when one precision analog channel must be converted for digital processing. The adjustable 400 mV to 5 V external reference supports both millivolt-level instrumentation and wider input ranges. The ADC's 13-bit result can feed calibration, curve fitting, or control algorithms over SPI. Accuracy is ultimately determined by reference stability, analog front-end noise, grounding, and calibration rather than resolution alone, so evaluate those elements together.
推薦
Portable Measurement Instrument
The MCP3301T-CI/SN fits portable measurement instruments where a compact 8-pin SOIC converter can replace a larger or more complex data-acquisition implementation. Its single differential input simplifies analog routing, while the SPI interface allows connection to a compact microcontroller. The converter can reach 100 ksps, but portable instruments often operate at a lower rate to reduce energy use and improve rejection of high-frequency noise. The external reference should be shutdown with the system when battery life is critical.
推薦
推薦產品摘要
工程參考資料,適用於 MCP3301T-CI/SN — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP3301T-BI/SN | MCP3201T-CI/SN | MCP3201T-BI/SN |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-pin SOIC, 150 mil | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Resolution | 13 bits | 13 bits | 12 bits | 12 bits |
| Input Channels | 1 channel | 1 channel | 1 channel | 1 channel |
| Input Architecture | Fully differential | Fully differential | Differential | Differential |
| Conversion Method | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) | Successive approximation (SAR) |
| Digital Interface | SPI | SPI | SPI | SPI |
| External Reference | Required; 400 mV to 5 V | External reference | External reference | External reference |
主要差異化特點
- Higher conversion resolution within the same SPI SOIC architecture (對比MCP3201T-CI/SN)
- Same 13-bit conversion core and package family (對比MCP3301T-BI/SN)
- Differential measurement in a compact 8-pin package (對比ADS7818)
設計說明
Route VREF+, VREF-, VIN+, and VIN- as short analog traces, and place the reference bypass capacitor close to the VREF+ and VREF- pins. Keep SPI lines away from the input and reference nodes to reduce capacitive coupling. A continuous ground plane under the converter and a quiet return path for the analog signals provide a lower-impedance connection between the input source, reference, and converter.
Decouple VDD locally with ceramic capacitors selected for the supply rail and place them close to the converter. Because the ADC has an external reference, treat the reference source as part of the measurement chain rather than an optional support circuit. Reference noise and supply ripple can appear directly in the conversion result. Use separate filtering or a dedicated reference buffer when the reference source also serves noisy loads.
Do not assume the 13-bit code count guarantees 13 effective bits of real-world accuracy. Source impedance, acquisition time, reference stability, input noise, and PCB leakage can reduce usable resolution. For slow-changing measurements, average multiple samples and apply digital filtering; for fast signals, verify that the source settles before sampling and that SPI timing conforms to the Microchip Technology datasheet.
Use a fully differential input arrangement whenever the source can provide balanced outputs. This reduces sensitivity to common-mode voltage and noise present equally on VIN+ and VIN-. If the source is single-ended, bias it correctly within the input range and account for the ADC's differential architecture. Avoid grounding one input arbitrarily because that changes the usable signal span and may prevent the converter from utilizing its full code range.
合規資訊
RoHS compliance is indicated for MCP3301T-CI/SN. No specific AEC-Q100 qualification, REACH declaration, halogen-free designation, or conflict-minerals statement was identified for this exact orderable device.