MCP3422A5-E/SN - 18-Bit Dual-Channel Delta-Sigma ADC
MPN: MCP3422A5-E/SN ✓ 啟用中MCP3422A5-E/SN 概覽
An ADC converts an analog voltage into a digital value for measurement, control, or data logging. The MCP3422 belongs to the delta-sigma ADC class, which uses continuous-time sampling and digital filtering to deliver high resolution and low noise. Within the signal-chain hierarchy, it sits between sensors or front-end circuits and a digital controller, combining an analog measurement function with an I²C interface.
The two differential input channels support measurement of bipolar signals around the selected conversion gain. An on-board precision 2.048 V reference establishes the differential input range of ±2.048 V. Differential operation rejects common-mode voltage, while the 18-bit converter resolution supports high-resolution measurements in sensors, industrial controls, and instrumentation. The A5 variant is identified in product listings as a 4 sps delta-sigma ADC.
The MCP3422 architecture integrates the converter, on-board reference, input channels, and digital control into one compact IC. Conversion data is transferred over the two-wire serial interface, reducing the number of connections required between the analog measurement section and a host controller. Its single-supply operation also simplifies systems that use either 3.3 V or 5 V logic and analog rails. Configuration and measurement sequencing are handled through the device command interface rather than separate programming pins.
Typical uses include bridge or ratiometric sensor measurement, industrial process monitoring, low-frequency instrumentation, portable data acquisition, and embedded control systems with slow-changing analog inputs. The differential inputs are especially useful when the measured quantity appears as a small voltage superimposed on a larger common-mode voltage. The 4 sps conversion rate is appropriate for temperature, pressure, load, and position measurements rather than high-bandwidth waveform acquisition.
Designers should apply input filtering and carefully observe the differential input range, because the 2.048 V reference also determines the usable signal span. Place input and reference components near the device, provide a clean supply connection, and route I²C signals away from sensitive analog inputs. Verify the conversion rate and digital timing against the required control-loop interval before fixing the system sampling schedule.
This page combines manufacturer specifications, package information, pricing availability, selectable drop-in alternatives, and application-focused design guidance. It also provides practical context for choosing the A5 speed grade, planning the analog front end, and evaluating replacement options without changing the 8-pin SOIC footprint.
直接替換替代品,適用於 MCP3422A5-E/SN — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP3422A5-E/SN (相同外形與佔位) — 差異在於 Conversion Rate, Operating Temperature Range, Resolution.
MCP3422A2-E/SN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP3422A0-E/SN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP3422A4-E/SN
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MCP3422A6-E/SN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP3422-E/SN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP3422A5-E/SN 最大額定值與電氣特性
| Converter Type | Delta-sigma ADC |
| 解析度 | 18 bit |
| Input Channels | 2 channels |
| Input Architecture | Differential inputs |
| Conversion Rate | 4 sps |
| On-Board Reference Voltage | 2.048 V |
| Differential Input Range | +/-2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Supply Type | Single supply |
| Serial Interface | Two-wire I2C-compatible interface |
| 工作溫度範圍 | -40 °C to +125 °C |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| Automotive Classification | Automotive |
MCP3422A5-E/SN 8-pin soic 腳位配置指南
MCP3422A5-E/SN(8-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP3422A5-E/SN.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP3422A5-E/SN 適用於 6 應用s: Industrial Pressure and Temperature Monitoring, Load Cell and Bridge Sensor Interface, Battery-Powered Portable Instrumentation, Precision Analog Signal Acquisition, Automotive Sensor Interface, Environmental and IoT Sensor Nodes.
Industrial Pressure and Temperature Monitoring
The MCP3422A5-E/SN fits industrial pressure, temperature, and process-monitoring systems whose sensor outputs change slowly enough for its 4 sps conversion rate. Two differential channels allow the controller to monitor related variables without adding another ADC package. The 18-bit conversion resolution preserves fine numerical detail, while the on-board 2.048 V reference provides a stable measurement basis over the ±2.048 V differential input range. Place input protection and anti-alias networks ahead of the converter, keep the analog traces short, and decouple the 2.7 V to 5.5 V supply close to the IC. For pressure loops with strict latency requirements, compare the timing of the A5 grade against a faster family option before finalizing the acquisition schedule.
推薦
Load Cell and Bridge Sensor Interface
The MCP3422A5-E/SN is appropriate for load-cell, strain-gauge, and resistive bridge measurements where the useful signal is small and differential. Its two differential input channels provide matched signal paths for bridge excitation and measurement arrangements, while 18-bit resolution improves the numerical granularity of the converted result. The on-board 2.048 V reference can support ratiometric behavior when the bridge excitation is referenced appropriately. Because the device converts at 4 sps, it is best suited to static force readings, slow loading events, and periodic production checks rather than vibration analysis. Use low-noise excitation, shielded analog routing, and differential input filtering to prevent environmental interference from degrading the measurement.
推薦
Battery-Powered Portable Instrumentation
The MCP3422A5-E/SN supports portable measurement instruments that need high-resolution readings from low-frequency sensor channels while operating from a 2.7 V to 5.5 V supply. The two-channel differential architecture limits the number of analog packages required in a compact design, and the two-wire serial interface reduces wiring between the measurement front end and an embedded controller. Its 4 sps conversion rate is suitable for periodic readings from gas, environmental, or wearable sensors where energy use is more important than rapid waveform capture. During layout, isolate the I²C bus from analog inputs, provide local supply bypassing, and disable or power-gate unused analog paths when the system supports it for longer battery life.
推薦
Precision Analog Signal Acquisition
The MCP3422A5-E/SN can be used for slow precision signal acquisition when the application requires 18-bit numerical resolution and differential input measurement rather than wideband sampling. Its two channels allow simultaneous or sequential observation of two related analog quantities, and the 2.048 V on-board reference establishes a convenient input span of ±2.048 V differentially. The 4 sps rate makes the device appropriate for temperature, position, voltage, and environmental monitoring. Engineers should design the front end around the converter's differential range, account for offset and gain calibration, and avoid routing high-energy switching nodes close to the input pins. A digital filter can improve noise performance when the updated result is needed less frequently than the raw conversion cadence.
推薦
Automotive Sensor Interface
The MCP3422A5-E/SN is associated with automotive-class applications and can support slow-changing vehicle sensor measurements when its operating range of -40 °C to +125 °C satisfies the design requirement. Two differential channels are useful for pressure, position, temperature, and other ratiometric or bridge-derived quantities, while 18-bit resolution supports detailed result representation. The 4 sps conversion rate fits periodic vehicle monitoring rather than high-bandwidth safety dynamics. Engineers must still verify qualification, EMC, transient protection, and fault-tolerance requirements for the complete automotive subsystem. Use robust input conditioning and isolation where required, and confirm the appropriate automotive qualification status before production release.
推薦
Environmental and IoT Sensor Nodes
The MCP3422A5-E/SN fits environmental sensor nodes that periodically measure low-frequency inputs such as humidity, ambient temperature, soil potential, or light levels. The two differential channels reduce the need for separate converter packages, while the I²C-compatible interface supports connection to a low-power embedded controller. Its 18-bit result scale and 2.048 V on-board reference provide useful measurement granularity in compact systems. Because the converter operates at 4 sps, average repeated readings when additional noise rejection is needed rather than treating it as a high-speed oscilloscope channel. Keep analog filtering close to the device, provide stable supply bypassing, and use a ground layout that prevents sensor return currents from flowing through the converter's reference and input paths.
推薦
推薦產品摘要
工程參考資料,適用於 MCP3422A5-E/SN — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP3422A2-E/SN | MCP3422A0-E/SN | MCP3422A4-E/SN | MCP3422A6-E/SN | MCP3422-E/SN |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Resolution | 18 bit | Up to 18 bit | Up to 18 bit | Up to 18 bit | Up to 18 bit | 16 bit |
| Input Channels | 2 differential channels | 2 differential channels | 2 differential channels | 2 differential channels | 2 differential channels | 2 differential channels |
| Conversion Rate | 4 sps | 3.75 sps | 15 sps | 1.25 sps | 15 sps | 3.75 sps |
| On-Board Reference | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V |
| Differential Input Range | +/-2.048 V | +/-2.048 V | +/-2.048 V | +/-2.048 V | +/-2.048 V | +/-2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Serial Interface | Two-wire I2C-compatible | Two-wire I2C-compatible | Two-wire I2C-compatible | Two-wire I2C-compatible | Two-wire I2C-compatible | Two-wire I2C-compatible |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C |
主要差異化特點
- Balanced resolution and conversion interval (對比MCP3422A4-E/SN)
- Higher resolution than the base family grade (對比MCP3422-E/SN)
- More suitable timing for responsive periodic acquisition (對比MCP3422A2-E/SN)
- Lower conversion demand than the 15 sps A0 grade (對比MCP3422A0-E/SN)
設計說明
Route the two differential input pairs as closely matched, parallel traces where practical, and keep them away from switching nodes, relay contacts, and the I²C clock line. Differential symmetry helps preserve common-mode rejection, while short traces reduce susceptibility to capacitive pickup and conversion error. Connect input filtering components directly beside the corresponding ADC pins and maintain a continuous ground return so analog currents do not share a path with the digital interface.
Place the supply bypass capacitor next to the MCP3422A5-E/SN power pin and provide a low-impedance return to the device ground. The converter operates from 2.7 V to 5.5 V, but the selected rail still needs adequate headroom during reference and converter activity. Avoid routing sensor excitation current through the analog ground region, and decouple any upstream regulator near the ADC rather than relying on capacitance located elsewhere on the board.
Do not treat the 4 sps A5 conversion rate as a general-purpose waveform acquisition speed. The device is better suited to temperature, pressure, strain, and other low-frequency measurements where a periodic result is sufficient. Confirm differential input polarity, the ±2.048 V range established by the on-board reference, and the controller's conversion-completion timing. Using the wrong family speed grade can alter the expected sample interval even though the 8-pin SOIC footprint remains the same.
For noisy sensor nodes, average multiple converted results or use the converter's digital filtering options when the application can tolerate additional latency. Add passive input filtering only after checking its effect on settling and conversion timing. Maintain a quiet reference path, avoid sharing high-current returns near the analog pins, and isolate the I²C bus from analog inputs. This is particularly important when the MCP3422A5-E/SN is mounted near a switching supply or display connector.
合規資訊
A listing describes the MCP3422A5-E/SN as automotive, but no specific AEC-Q100 qualification status or other compliance declaration is stated. Confirm all environmental and material-compliance requirements with the manufacturer before production release.