MCP6021-E/SN - 10MHz RRIO Op Amp | Microchip Technology
MPN: MCP6021-E/SN ✓ 啟用中MCP6021-E/SN 概覽
An operational amplifier, or op amp, is an analog signal-conditioning IC that compares an input voltage with a feedback-derived reference and amplifies the difference. The MCP6021 belongs to the general-purpose amplifier hierarchy: operational amplifier, voltage-feedback amplifier, analog IC, and semiconductor. Its combination of moderate bandwidth, low noise, low power consumption, and flexible input/output ranges makes it useful for sensor buffers, audio paths, active filters, and low-power data-acquisition front ends.
Key features include a 10 MHz gain-bandwidth product, input-voltage noise of 8.7 nV/√Hz, typical input offset voltage below 0.5 mV, and total harmonic distortion plus noise of 0.00053%. The single amplifier supports supply voltages from 2.5 V to 5.5 V and consumes less than 1.35 mA quiescent current according to the family datasheet. These characteristics support compact designs where both signal-chain bandwidth and operating efficiency are important.
The MCP6021 uses Microchip's CMOS analog technology to provide low bias current, high open-loop gain, high-speed operation, and rail-to-rail output swing. Rail-to-rail input operation reduces the restriction imposed by common-mode input limits, while the output stage can approach either supply rail under suitable load conditions. The 10 MHz bandwidth is sufficient for many audio, filtering, buffering, and general instrumentation tasks without requiring a high-current, high-speed amplifier.
Typical applications include portable sensor interfaces, microphone and audio preamplification, active analog filters, battery-powered instruments, and low-voltage industrial control systems. The low-noise specification is valuable when amplifying weak signals, while the approximately 1 mA operating current helps extend battery life in portable equipment. The rail-to-rail input and output behavior also simplifies circuits that operate across most of the available supply range.
When using the MCP6021-E/SN, preserve the unity-gain stability conditions of the selected gain configuration and route feedback components to minimize parasitic capacitance. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should remain away from high-current switching paths. Stable operation also depends on keeping the output within its linear range and accounting for input and output common-mode behavior.
This product record combines manufacturer specifications, package and pin information, sourcing guidance, and practical circuit considerations. It also identifies same-family drop-in alternatives for PCB reuse and organizes the important differences into a direct engineering comparison, supporting faster component selection without replacing the need to review the manufacturer datasheet.
直接替換替代品,適用於 MCP6021-E/SN — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MCP6021R-E/SN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6022-E/SN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6023-E/SN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6021-E/SN 最大額定值與電氣特性
| Amplifier Type | Single-circuit general-purpose operational amplifier |
| Gain-Bandwidth Product | 10 MHz |
| Input Noise Density | 8.7 nV/√Hz |
| Typical Operating Current | 1.0 mA |
| Maximum Quiescent Current | Less than 1.35 mA |
| Input Offset Voltage | Less than 0.5 mV typical |
| Supply Voltage Range | 2.5 V to 5.5 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Total Harmonic Distortion Plus Noise | 0.00053% |
| Technology | CMOS |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| Number of Amplifiers | 1 |
MCP6021-E/SN 腳位配置
| 腳位 1 | NC — Not connected |
| 腳位 2 | -IN — Inverting input |
| 腳位 3 | +IN — Non-inverting input |
| 腳位 4 | V- — Negative supply or ground connection |
| 腳位 5 | V+ — Positive supply connection |
| 腳位 6 | OUT — Amplifier output |
| 腳位 7 | NC — Not connected |
| 腳位 8 | NC — Not connected |
典型應用
MCP6021-E/SN 適用於 6 應用s: Portable Sensor Signal Conditioning, Microphone and Audio Preamplification, Active Analog Filtering, Battery-Powered Instrumentation, Industrial Control and Data Acquisition, General-Purpose Voltage Buffer.
Portable Sensor Signal Conditioning
The MCP6021-E/SN fits low-voltage sensor front ends because its rail-to-rail input stage accepts signals near the supply limits while the 10 MHz gain-bandwidth product supports responsive buffering. With a 2.5 V to 5.5 V supply and approximately 1.0 mA typical operating current, it helps preserve battery life in portable instruments. Place the amplifier close to the sensor or transducer, use short traces, and select a gain that preserves amplifier stability. The 8.7 nV/√Hz noise specification is valuable for weak sensor outputs, while the input offset voltage below 0.5 mV typical helps reduce DC error after calibration.
推薦
Microphone and Audio Preamplification
The MCP6021-E/SN is appropriate for microphone buffers and low-level audio preamplifiers because it combines 8.7 nV/√Hz input noise with 0.00053% THD+N. Its 10 MHz bandwidth is substantially wider than the audible band, allowing the closed-loop gain to be set without bandwidth becoming the limiting factor. Use conventional non-inverting or inverting amplifier arrangements and verify output swing into the microphone bias and downstream load. The rail-to-rail input stage is especially useful in 2.5 V to 5.5 V systems where the sensor or microphone signal may occupy much of the available voltage range.
推薦
Active Analog Filtering
The MCP6021-E/SN can implement first- and higher-order active filters where a 10 MHz gain-bandwidth product provides useful closed-loop bandwidth beyond the signal of interest. Its low-noise operation improves the filter's contribution to small-signal signal-to-noise ratio, while approximately 1.0 mA typical operating current limits the impact on portable power budgets. Select resistor and capacitor values against the required closed-loop gain, and confirm the intended compensation or stability configuration. Component tolerances and the amplifier's input-voltage noise directly affect filter accuracy and output noise, so both should be included in the design calculation.
推薦
Battery-Powered Instrumentation
The MCP6021-E/SN suits low-power instrumentation because it operates from 2.5 V to 5.5 V while consuming less than 1.35 mA quiescent current, with a typical operating current of 1.0 mA. The 10 MHz bandwidth permits measurement channels to amplify signals beyond narrow sensor-bandwidth requirements, and the 8.7 nV/√Hz noise specification supports precision-oriented designs. Use low-leakage input protection components, avoid unnecessary bias currents, and evaluate the complete measurement chain because reference accuracy, resistor noise, and ADC input loading can dominate final performance.
推薦
Industrial Control and Data Acquisition
The MCP6021-E/SN can condition low-level analog signals in industrial control and data-acquisition systems where a compact, low-power amplifier is required. Rail-to-rail input operation increases usable signal span, while the 0.00053% THD+N specification supports low-distortion acquisition. A 10 MHz gain-bandwidth product also provides margin for filtering and higher-bandwidth sensor interfaces. Design the layout to separate sensitive inputs from switching nodes, provide local supply decoupling, and confirm the exact operating-temperature rating for the selected ordering code before deploying the amplifier in industrial equipment.
推薦
General-Purpose Voltage Buffer
The MCP6021-E/SN works as a unity-gain voltage buffer when the source has high impedance and the following stage requires lower output impedance. Its rail-to-rail input and output behavior covers most of a low-voltage signal range, and the 10 MHz bandwidth provides more capability than a basic precision buffer. Check the output load and capacitive-drive limits before using the device as a direct replacement for a wider-bandwidth buffer. Place input, feedback, and decoupling connections so that parasitic capacitance does not alter the intended closed-loop response or stability margin.
推薦
推薦產品摘要
工程參考資料,適用於 MCP6021-E/SN — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP6021R-E/SN | MCP6022-E/SN | MCP6023-E/SN |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Number of Amplifiers | 1 | 1 | 2 | 2 |
| Gain-Bandwidth Product | 10 MHz | 10 MHz | 10 MHz | 10 MHz |
| Input Noise Density | 8.7 nV/√Hz | 8.7 nV/√Hz | 8.7 nV/√Hz | 8.7 nV/√Hz |
| Supply Voltage Range | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Special Feature | None | Rail-to-rail output stage | Dual amplifier | Dual amplifier with Chip Select |
主要差異化特點
- Uses only one amplifier channel in the 8-pin SOIC footprint (對比MCP6022-E/SN)
- Simplifies designs that do not require the MCP6021R rail-to-rail output stage (對比MCP6021R-E/SN)
- Avoids the unused-channel and control-pin overhead of the selectable dual amplifier (對比MCP6023-E/SN)
設計說明
Place the supply-decoupling capacitor directly between pins 4 and 5, with a short and low-inductance return path. Keep the non-inverting input trace short and away from the output and supply routes. The MCP6021-E/SN is a high-frequency 10 MHz device, so PCB resistance and inductance can create measurable supply noise or oscillation even when the schematic appears correct.
Do not assume that rail-to-rail input operation permits an input exactly at or beyond either supply rail. Maintain the datasheet's input and output common-mode limits, including restrictions associated with output current. In amplifier designs, also verify that the selected closed-loop gain is stable with the feedback network, source impedance, and parasitic capacitance present on the assembled board.
For low-level sensor signals, use a guarding and grounding strategy that minimizes leakage from PCB contamination and from adjacent digital or switching circuits. The amplifier's 8.7 nV/√Hz input noise is a device specification, but the total input-referred noise also includes resistor noise, source impedance, bandwidth, and leakage current. These effects must be evaluated together when designing a precision measurement front end.
The MCP6021-E/SN operates from 2.5 V to 5.5 V and has a typical operating current of 1.0 mA. Use a regulator with adequate low-voltage stability and check its behavior at light load, where supply current is minimal. The amplifier's operating current is only one part of the power budget; sensor biasing, pull-up networks, ADC leakage, and regulator quiescent current can materially affect battery life.
合規資訊
Compliance declarations are not stated in the manufacturer pages or distributor records used for this product record. The -E/SN ordering code includes an extended-temperature variant, but AEC-Q100 qualification must not be inferred from that temperature designation.