MCP6033-E/MC - 10 kHz Low-Power RRIO Op Amp | Microchip
MPN: MCP6033-E/MC ✓ 啟用中MCP6033-E/MC 概覽
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages while providing high input impedance and low output impedance. Operational amplifiers form the general-purpose building blocks of the linear amplifier category, which belongs to the broader amplifier IC and signal-conditioning hierarchy. Their common uses include signal buffering, sensor amplification, active filtering, current-to-voltage conversion, and low-level analog signal conditioning.
The MCP6033 combines low power consumption with precision-oriented characteristics. Its rail-to-rail input stage accepts signals approaching the supply rails, while rail-to-rail output operation provides useful output swing near both rail limits. The 1.8 V minimum operating supply supports low-voltage systems, while its 18 V maximum rating provides headroom for higher-voltage industrial designs. A Chip Select pin provides an additional path for reducing power consumption when the amplifier is not needed.
The MCP6033 is intended for low-bandwidth applications where energy efficiency and compactness matter more than high slew rate or wideband gain. The listed maximum input offset voltage is 150 µV, and the 10 kHz gain-bandwidth product is suitable for precision buffers, slow sensor paths, and low-frequency active filters. Its small 8-DFN exposed-pad package also requires careful PCB layout and thermal management.
Typical uses include portable sensor interfaces, battery-powered instrumentation, industrial control signals, low-frequency filter stages, and embedded analog measurement systems. The low quiescent current is particularly useful in systems where the amplifier remains connected to a supply while its output is disabled through the Chip Select function.
Designers should preserve the exposed-pad connection to the PCB ground plane and place input, output, supply, and decoupling connections to minimize leakage, oscillation, and signal-integrity problems. Stable operation also depends on following the manufacturer recommendations for external capacitance, output loading, and gain configuration.
This page combines manufacturer-device positioning with package, pricing, replacement, comparison, and practical design guidance. It also explains the functional choices among MCP6033-family Chip Select variants so engineers can distinguish otherwise similar ordering codes before placing a part on a board.
直接替換替代品,適用於 MCP6033-E/MC — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP6033-E/MC (相同外形與佔位) — 差異在於 Package, Quiescent Current, Temperature Grade.
MCP6031-E/MC
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MCP6032-E/MC
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6034-E/MC
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6031-I/MC
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6032-I/MC
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6034-I/MC
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6033-E/MC 最大額定值與電氣特性
| Amplifier Type | Single general-purpose precision operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 10 kHz |
| Minimum Operating Supply Voltage | 1.8 V |
| Maximum Supply Voltage | 18 V |
| 靜態電流 | Less than 1 µA |
| Input Type | Rail-to-rail |
| 輸出類型 | Rail-to-rail |
| Maximum Input Offset Voltage | 150 µV |
| Chip Select | Yes |
| 封裝 | 8-DFN, 2 x 3 mm |
| Package Height | 0.9 mm |
| Thermal Pad | Exposed pad |
| 安裝類型 | Surface mount |
| Temperature Grade | E temperature grade |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
MCP6033-E/MC 0.9 mm 腳位配置指南
MCP6033-E/MC(0.9 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP6033-E/MC.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP6033-E/MC 適用於 6 應用s: Battery-Powered Sensor Interfaces, Portable Industrial Measurement, Low-Frequency Active Filters, Precision Signal Buffering, Data-Acquisition Front Ends, Low-Power Control and Monitoring.
Battery-Powered Sensor Interfaces
The MCP6033-E/MC fits low-power sensor front ends that operate from a 1.8 V rail and require low standby consumption. Its less-than-1 µA quiescent current limits continuous overhead, while rail-to-rail input and output operation allows the amplifier to work with a restricted signal range near the supply rails. Place the device between the sensor and an ADC input to provide buffering and gain without introducing a high quiescent load. The 10 kHz gain-bandwidth product suits slow temperature, pressure, or position signals, but it is not intended for high-speed waveform amplification.
推薦
Portable Industrial Measurement
The MCP6033-E/MC supports portable industrial instruments that combine slow sensor measurement with strict power budgets. Its 18 V maximum supply rating provides compatibility with industrial supply transients and test equipment, while the 1.8 V minimum supply supports compact low-voltage sections of the system. The single-amplifier 8-DFN package conserves board area, and the Chip Select pin can reduce power consumption when a measurement channel is inactive. Designers should use a stable reference, maintain input common-mode voltage within the rail-to-rail operating region, and verify offset behavior across the required temperature range.
推薦
Low-Frequency Active Filters
MCP6033-E/MC can implement first- and second-order active filters for slowly varying industrial or sensor signals. Its 10 kHz gain-bandwidth product provides loop gain above the intended filter cutoff, while low quiescent current is valuable in continuously powered monitoring systems. Rail-to-rail input and output operation also improves usable signal range in low-voltage designs. Because the amplifier is intended for precision and low-bandwidth service rather than high slew rate, component tolerances, capacitor selection, and output loading should be evaluated to maintain the desired cutoff and stability.
推薦
Precision Signal Buffering
The MCP6033-E/MC is appropriate for buffering high-impedance sensor nodes before digitization. Rail-to-rail input behavior accommodates signals approaching either supply rail, and the listed maximum input offset voltage of 150 µV helps preserve small-signal accuracy. The amplifier's low quiescent current is especially useful in instrument chains that must remain connected to the supply continuously, while Chip Select can provide an additional control mechanism for duty-cycled measurements. The relatively narrow 10 kHz bandwidth makes this a better fit for temperature, pressure, strain, and chemical-sensor signals than for communications or audio-rate waveforms.
推薦
Data-Acquisition Front Ends
MCP6033-E/MC can condition a low-level analog channel before a precision converter in a compact data-acquisition system. Its 1.8 V minimum supply supports low-power converter environments, and the 2 x 3 mm 8-DFN package leaves room for dense analog routing. The device can buffer an external sensor or drive a moderate input impedance without the higher current demand of a wideband amplifier. System designers should use short traces, maintain a clean ground reference, follow the exposed-pad layout guidance, and verify that the selected ADC's sampling rate does not exceed the amplifier's intended bandwidth class.
推薦
Low-Power Control and Monitoring
The MCP6033-E/MC is useful in control and monitoring circuits where the signal changes slowly but system standby power must remain low. Its less-than-1 µA quiescent current helps limit continuous consumption, and the Chip Select pin supports explicit power-state control in multichannel equipment. The 10 kHz bandwidth is more than adequate for setpoint interfaces, slow feedback loops, and status-signal conditioning. When using the amplifier in feedback, verify loop stability and the effect of output capacitance. For new layouts, connect the exposed pad as directed by the manufacturer and place supply bypassing close to the device.
推薦
推薦產品摘要
工程參考資料,適用於 MCP6033-E/MC — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP6031-E/MC | MCP6032-E/MC | MCP6034-E/MC | MCP6031-I/MC | MCP6032-I/MC | MCP6034-I/MC |
|---|---|---|---|---|---|---|---|
| Package | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFFN (2 x 3 mm) | 8-DFN (2 x 3 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Number of Channels | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| Gain-Bandwidth Product | 10 kHz | 10 kHz | 10 kHz | 10 kHz | 10 kHz | 10 kHz | 10 kHz |
| Minimum Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Maximum Supply Voltage | 18 V | 18 V | 18 V | 18 V | 18 V | 18 V | 18 V |
| Quiescent Current | Less than 1 µA | Less than 1 µA | Less than 1 µA | Less than 1 µA | Less than 1 µA | Less than 1 µA | Less than 1 µA |
| Maximum Input Offset Voltage | 150 µV | 150 µV | 150 µV | 150 µV | 150 µV | 150 µV | 150 µV |
| Input and Output Operation | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
主要差異化特點
- Low-power operation combined with a wide supply range (對比MCP6071T-E/OT)
- Chip Select supports explicit power-state management (對比MCP6031-E/MC)
- Compact exposed-pad package supports dense analog layouts (對比NE5532D8R2G)
設計說明
Follow the manufacturer land pattern and route the exposed pad to a low-impedance ground plane. Place the input and output traces away from switching nodes and keep the feedback loop compact. Because the MCP6033-E/MC is intended for low-bandwidth precision applications, slow signals remain well behaved when supply bypassing, grounding, and output routing are controlled.
The Chip Select pin provides an additional mechanism for reducing power consumption when the amplifier output is not required. Define its logic levels and state transitions in the system controller, and account for control-pin leakage when calculating standby power. Confirm the selected MCP6033-family member has the required Chip Select polarity and thresholds before updating the firmware or schematic.
Do not treat rail-to-rail input and output operation as unlimited output swing. The usable range still depends on load current, output-capacitance limits, common-mode behavior, and supply voltage. Verify these conditions in the manufacturer datasheet, especially when operating at 1.8 V or driving a load that includes cable capacitance or downstream switching input.
合規資訊
No specific compliance declarations were identified for this ordering code in the cited product information.