MCP6033-E/MC - 10 kHz Low-Power RRIO Op Amp | Microchip
MPN: MCP6033-E/MC ✓ Hoạt độngMCP6033-E/MC Tóm tắt
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages while providing high input impedance and low output impedance. Operational amplifiers form the general-purpose building blocks of the linear amplifier category, which belongs to the broader amplifier IC and signal-conditioning hierarchy. Their common uses include signal buffering, sensor amplification, active filtering, current-to-voltage conversion, and low-level analog signal conditioning.
The MCP6033 combines low power consumption with precision-oriented characteristics. Its rail-to-rail input stage accepts signals approaching the supply rails, while rail-to-rail output operation provides useful output swing near both rail limits. The 1.8 V minimum operating supply supports low-voltage systems, while its 18 V maximum rating provides headroom for higher-voltage industrial designs. A Chip Select pin provides an additional path for reducing power consumption when the amplifier is not needed.
The MCP6033 is intended for low-bandwidth applications where energy efficiency and compactness matter more than high slew rate or wideband gain. The listed maximum input offset voltage is 150 µV, and the 10 kHz gain-bandwidth product is suitable for precision buffers, slow sensor paths, and low-frequency active filters. Its small 8-DFN exposed-pad package also requires careful PCB layout and thermal management.
Typical uses include portable sensor interfaces, battery-powered instrumentation, industrial control signals, low-frequency filter stages, and embedded analog measurement systems. The low quiescent current is particularly useful in systems where the amplifier remains connected to a supply while its output is disabled through the Chip Select function.
Designers should preserve the exposed-pad connection to the PCB ground plane and place input, output, supply, and decoupling connections to minimize leakage, oscillation, and signal-integrity problems. Stable operation also depends on following the manufacturer recommendations for external capacitance, output loading, and gain configuration.
This page combines manufacturer-device positioning with package, pricing, replacement, comparison, and practical design guidance. It also explains the functional choices among MCP6033-family Chip Select variants so engineers can distinguish otherwise similar ordering codes before placing a part on a board.
Bộ thay thế dễ dàng lắp đặt cho MCP6033-E/MC — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với MCP6033-E/MC (cùng hình factor và footprint) — khác nhau ở Package, Quiescent Current, Temperature Grade.
MCP6031-E/MC
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →MCP6032-E/MC
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MCP6034-E/MC
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MCP6031-I/MC
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MCP6032-I/MC
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MCP6034-I/MC
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
MCP6033-E/MC Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single general-purpose precision operational amplifier |
| Number of Channels | 1 channel |
| Gain-Bandwidth Product | 10 kHz |
| Minimum Operating Supply Voltage | 1.8 V |
| Maximum Supply Voltage | 18 V |
| Điện áp yên tĩnh | Less than 1 µA |
| Input Type | Rail-to-rail |
| Kiểu đầu ra | Rail-to-rail |
| Maximum Input Offset Voltage | 150 µV |
| Chip Select | Yes |
| Hộp | 8-DFN, 2 x 3 mm |
| Package Height | 0.9 mm |
| Thermal Pad | Exposed pad |
| Kiểu lắp đặt | Surface mount |
| Temperature Grade | E temperature grade |
| Trạng thái RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Hướng dẫn cấu hình chân MCP6033-E/MC 0.9 mm
Cấu hình chân cho MCP6033-E/MC (0.9 mm gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho MCP6033-E/MC.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MCP6033-E/MC phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Interfaces, Portable Industrial Measurement, Low-Frequency Active Filters, Precision Signal Buffering, Data-Acquisition Front Ends, Low-Power Control and Monitoring.
Battery-Powered Sensor Interfaces
The MCP6033-E/MC fits low-power sensor front ends that operate from a 1.8 V rail and require low standby consumption. Its less-than-1 µA quiescent current limits continuous overhead, while rail-to-rail input and output operation allows the amplifier to work with a restricted signal range near the supply rails. Place the device between the sensor and an ADC input to provide buffering and gain without introducing a high quiescent load. The 10 kHz gain-bandwidth product suits slow temperature, pressure, or position signals, but it is not intended for high-speed waveform amplification.
Được đề xuất
Portable Industrial Measurement
The MCP6033-E/MC supports portable industrial instruments that combine slow sensor measurement with strict power budgets. Its 18 V maximum supply rating provides compatibility with industrial supply transients and test equipment, while the 1.8 V minimum supply supports compact low-voltage sections of the system. The single-amplifier 8-DFN package conserves board area, and the Chip Select pin can reduce power consumption when a measurement channel is inactive. Designers should use a stable reference, maintain input common-mode voltage within the rail-to-rail operating region, and verify offset behavior across the required temperature range.
Được đề xuất
Low-Frequency Active Filters
MCP6033-E/MC can implement first- and second-order active filters for slowly varying industrial or sensor signals. Its 10 kHz gain-bandwidth product provides loop gain above the intended filter cutoff, while low quiescent current is valuable in continuously powered monitoring systems. Rail-to-rail input and output operation also improves usable signal range in low-voltage designs. Because the amplifier is intended for precision and low-bandwidth service rather than high slew rate, component tolerances, capacitor selection, and output loading should be evaluated to maintain the desired cutoff and stability.
Được đề xuất
Precision Signal Buffering
The MCP6033-E/MC is appropriate for buffering high-impedance sensor nodes before digitization. Rail-to-rail input behavior accommodates signals approaching either supply rail, and the listed maximum input offset voltage of 150 µV helps preserve small-signal accuracy. The amplifier's low quiescent current is especially useful in instrument chains that must remain connected to the supply continuously, while Chip Select can provide an additional control mechanism for duty-cycled measurements. The relatively narrow 10 kHz bandwidth makes this a better fit for temperature, pressure, strain, and chemical-sensor signals than for communications or audio-rate waveforms.
Được đề xuất
Data-Acquisition Front Ends
MCP6033-E/MC can condition a low-level analog channel before a precision converter in a compact data-acquisition system. Its 1.8 V minimum supply supports low-power converter environments, and the 2 x 3 mm 8-DFN package leaves room for dense analog routing. The device can buffer an external sensor or drive a moderate input impedance without the higher current demand of a wideband amplifier. System designers should use short traces, maintain a clean ground reference, follow the exposed-pad layout guidance, and verify that the selected ADC's sampling rate does not exceed the amplifier's intended bandwidth class.
Được đề xuất
Low-Power Control and Monitoring
The MCP6033-E/MC is useful in control and monitoring circuits where the signal changes slowly but system standby power must remain low. Its less-than-1 µA quiescent current helps limit continuous consumption, and the Chip Select pin supports explicit power-state control in multichannel equipment. The 10 kHz bandwidth is more than adequate for setpoint interfaces, slow feedback loops, and status-signal conditioning. When using the amplifier in feedback, verify loop stability and the effect of output capacitance. For new layouts, connect the exposed pad as directed by the manufacturer and place supply bypassing close to the device.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MCP6033-E/MC — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MCP6031-E/MC | MCP6032-E/MC | MCP6034-E/MC | MCP6031-I/MC | MCP6032-I/MC | MCP6034-I/MC |
|---|---|---|---|---|---|---|---|
| Package | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFFN (2 x 3 mm) | 8-DFN (2 x 3 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Number of Channels | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| Gain-Bandwidth Product | 10 kHz | 10 kHz | 10 kHz | 10 kHz | 10 kHz | 10 kHz | 10 kHz |
| Minimum Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Maximum Supply Voltage | 18 V | 18 V | 18 V | 18 V | 18 V | 18 V | 18 V |
| Quiescent Current | Less than 1 µA | Less than 1 µA | Less than 1 µA | Less than 1 µA | Less than 1 µA | Less than 1 µA | Less than 1 µA |
| Maximum Input Offset Voltage | 150 µV | 150 µV | 150 µV | 150 µV | 150 µV | 150 µV | 150 µV |
| Input and Output Operation | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
Bảo phân biệt quan trọng
- Low-power operation combined with a wide supply range (vsMCP6071T-E/OT)
- Chip Select supports explicit power-state management (vsMCP6031-E/MC)
- Compact exposed-pad package supports dense analog layouts (vsNE5532D8R2G)
Ghi chú thiết kế
Follow the manufacturer land pattern and route the exposed pad to a low-impedance ground plane. Place the input and output traces away from switching nodes and keep the feedback loop compact. Because the MCP6033-E/MC is intended for low-bandwidth precision applications, slow signals remain well behaved when supply bypassing, grounding, and output routing are controlled.
The Chip Select pin provides an additional mechanism for reducing power consumption when the amplifier output is not required. Define its logic levels and state transitions in the system controller, and account for control-pin leakage when calculating standby power. Confirm the selected MCP6033-family member has the required Chip Select polarity and thresholds before updating the firmware or schematic.
Do not treat rail-to-rail input and output operation as unlimited output swing. The usable range still depends on load current, output-capacitance limits, common-mode behavior, and supply voltage. Verify these conditions in the manufacturer datasheet, especially when operating at 1.8 V or driving a load that includes cable capacitance or downstream switching input.
Thông tin tuân thủ
No specific compliance declarations were identified for this ordering code in the cited product information.