MCP6044-I/SL - 14 kHz Quad CMOS Op Amp | Microchip
MPN: MCP6044-I/SL ✓ 啟用中MCP6044-I/SL 概覽
An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, filter, buffer, or compare small voltage signals. The quad configuration places four amplifiers in one package, reducing board area in designs that require multiple independent analog channels. Within the power-management and signal-processing hierarchy, the MCP6044 belongs to the CMOS operational-amplifier family, where rail-to-rail operation, low supply current, and low offset voltage are important characteristics for portable instrumentation.
Key features include a 14 kHz gain-bandwidth product, a typical operating current of 600 nA, and a less-than-3 mV offset voltage. The manufacturer specifies less than 1 uA maximum quiescent current per amplifier and operation from a single supply as low as 1.4 V. Rail-to-rail input capability permits the input common-mode voltage to approach the supply limits, while rail-to-rail output swing improves usable output range in low-voltage systems. These attributes make the part suitable for sensor conditioning, current sensing, low-frequency filtering, and general-purpose buffering.
The MCP6044 uses Microchip's advanced CMOS technology to provide low bias current, high open-loop gain, and high-speed operation relative to other micropower amplifiers. Its 14 kHz gain-bandwidth product is appropriate for low-frequency precision and instrumentation applications rather than high-speed waveform or signal-integrity workloads. Because each amplifier is independent, users can configure the four channels for different functions, such as a transimpedance stage, an active filter, an instrumentation amplifier, or four voltage followers, while observing common supply and grounding requirements.
Typical applications include low-power process-control loops, portable sensor interfaces, wearable-device signal paths, low-current measurement circuits, and low-voltage data-acquisition systems. A sensor front end can use one channel for amplification and another for buffering or filtering. An industrial measurement system can use the four channels to condition multiple inputs while keeping the power budget low. In each case, the 600 nA typical operating current helps preserve battery life, while the 1.4 V minimum supply supports compact low-energy systems.
Designers should verify signal bandwidth and closed-loop stability against the 14 kHz gain-bandwidth product, check common-mode and output limits over the full supply range, and provide adequate bypass capacitance close to the supply pins. Stable operation with capacitive loads requires careful gain selection and output isolation. The industrial temperature suffix identifies the specified qualification option, but the manufacturer datasheet should be used for the exact temperature limits and electrical tolerances.
This product page consolidates the manufacturer's principal operating characteristics, package information, drop-in family alternatives, and practical analog-design guidance. It supports engineers comparing the MCP6044-I/SL with nearby Microchip variants and designing low-power, rail-to-rail signal-conditioning circuits without changing the 14-lead SOIC footprint.
直接替換替代品,適用於 MCP6044-I/SL — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP6044-I/SL (相同外形與佔位) — 差異在於 Package, Typical Operating Current.
MCP6044-E/SL
✅ 直接替換聯絡詢價
查看資料表 →MCP6044T-I/SL
✅ 直接替換📋 參考替代品(不在目錄中)
MCP6044T-E/SL
✅ 直接替換📋 參考替代品(不在目錄中)
MCP6044-I/SL 最大額定值與電氣特性
| Amplifier Type | Quad CMOS operational amplifier |
| Number of Amplifiers | 4 circuits |
| Gain-Bandwidth Product | 14 kHz |
| Typical Operating Current | 600 nA |
| Maximum Quiescent Current per Amplifier | Less than 1 uA |
| Minimum Single-Supply Voltage | 1.4 V |
| Maximum Supply Voltage | 6 V |
| Input Operating Mode | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Typical Offset Voltage | Less than 3 mV |
| Typical Slew Rate | 0.003 V/us |
| Open-Loop Gain | High open-loop gain |
| Bias Current | Low bias current |
| 封裝 | 14-lead SOIC |
| 安裝類型 | Surface mount |
MCP6044-I/SL 14-lead soic 腳位配置指南
MCP6044-I/SL(14-lead soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP6044-I/SL.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP6044-I/SL 適用於 6 應用s: Low-Power Sensor Signal Conditioning, Battery-Powered Portable Instruments, Industrial Process-Control Loops, Wearable Device Analog Front Ends, Low-Voltage Data Acquisition, Precision Current and Voltage Monitoring.
Low-Power Sensor Signal Conditioning
The MCP6044-I/SL fits sensor front ends that must amplify small signals without exhausting a limited power budget. Its 600 nA typical operating current, less-than-3 mV typical offset voltage, and rail-to-rail input operation support measurements from sensors operating near the supply rails. Place the amplifier between the sensor and an ADC, use a gain appropriate for the 14 kHz gain-bandwidth product, and bypass the supply close to the device. The advantage is a four-channel package that can amplify, filter, or buffer several low-frequency sensor signals while remaining compatible with operation from a supply as low as 1.4 V.
推薦
Battery-Powered Portable Instruments
MCP6044-I/SL is appropriate for portable instruments that combine several analog channels with a constrained battery budget. A typical operating current of 600 nA and a maximum quiescent current below 1 uA per amplifier reduce the continuous load, while the 1.4 V minimum supply supports low-voltage energy sources and compact regulators. Four independent channels can handle excitation buffering, signal amplification, active filtering, and output buffering. Design the gain and settling requirements around the 14 kHz gain-bandwidth product and include the complete signal path in the battery-current calculation.
推薦
Industrial Process-Control Loops
The four rail-to-rail amplifier channels in MCP6044-I/SL support low-frequency industrial process-control and measurement circuits. The device can condition multiple sensor outputs, provide active filtering, or form gain stages around a controller input. Its less-than-3 mV typical offset voltage helps preserve small-signal accuracy, while the 14 kHz gain-bandwidth product covers slow process signals. Confirm the amplifier's common-mode behavior and output swing at the actual supply voltage, and keep high-energy switching loops physically separated from sensitive analog traces.
推薦
Wearable Device Analog Front Ends
MCP6044-I/SL suits wearable electronics that require multiple low-power analog functions in a small area. Four channels can amplify biometric or motion-sensor signals, implement crossover or smoothing filters, and buffer inputs to a mixed-signal controller. Rail-to-rail inputs and outputs improve signal utilization in compact single-supply systems, and the 600 nA typical operating current supports power-conscious operation. The 14 kHz bandwidth is suitable for many physiological and inertial signals, but gain, noise, and settling requirements must be checked for each channel before choosing passive-component values.
推薦
Low-Voltage Data Acquisition
MCP6044-I/SL can serve as the analog front end in a compact low-voltage data-acquisition system. Four channels can buffer multiplexed sensor inputs, implement anti-alias filtering, or provide programmable gain ahead of an ADC. Rail-to-rail input and output capability allows operation close to the supply limits, while the 1.4 V minimum supply supports low-energy conversion systems. Account for the 14 kHz gain-bandwidth product when selecting closed-loop gain, ensure settling is complete within the acquisition interval, and keep the analog return path continuous beneath the device.
推薦
Precision Current and Voltage Monitoring
MCP6044-I/SL is well matched to low-current monitoring circuits where amplifier self-consumption and input error must remain small. Its less-than-3 mV typical offset voltage can help limit measurement error in low-level amplifier stages, and its low quiescent current reduces disturbance to the monitored power budget. The four channels allow simultaneous conditioning of voltage, current, reference, or temperature signals. Select feedback values and gain carefully because the 14 kHz gain-bandwidth product defines the usable closed-loop bandwidth, and verify output swing under the worst-case load.
推薦
推薦產品摘要
工程參考資料,適用於 MCP6044-I/SL — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP6044-E/SL | MCP6044T-I/SL | MCP6044T-E/SL |
|---|---|---|---|---|
| Package | 14-lead SOIC | 14-lead SOIC | 14-lead SOIC | 14-lead SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Amplifier Configuration | Quad operational amplifier | Quad operational amplifier | Quad operational amplifier | Quad operational amplifier |
| Gain-Bandwidth Product | 14 kHz | 14 kHz | 14 kHz | 14 kHz |
| Typical Operating Current | 600 nA | 600 nA | 600 nA | 600 nA |
| Maximum Quiescent Current per Amplifier | Less than 1 uA | Less than 1 uA | Less than 1 uA | Less than 1 uA |
| Minimum Single-Supply Voltage | 1.4 V | 1.4 V | 1.4 V | 1.4 V |
| Maximum Supply Voltage | 6 V | 6 V | 6 V | 6 V |
| Input and Output Operation | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
主要差異化特點
- Very low power for a quad amplifier (對比MCP6044-E/SL)
- Single-supply operation supports compact systems (對比MCP6044T-I/SL)
- Rail-to-rail signal range improves utilization (對比MCP6044T-E/SL)
設計說明
Place the supply bypass capacitor immediately beside the MCP6044-I/SL supply and ground connections. Keep the high-frequency return path short and avoid routing sensitive analog inputs across the noisy supply path. Because the device supports operation from 1.4 V, verify regulator startup, dropout behavior, ground offset, and output-swing margins at the lowest operating supply. The amplifier's less-than-1 uA maximum quiescent current per channel is useful for battery designs, but total system current also includes load, bias-network, and sensor currents.
Do not select a high closed-loop gain without checking the 14 kHz gain-bandwidth product. For example, a noise gain of 10 leaves approximately 1.4 kHz of nominal gain-bandwidth, while higher noise gains reduce it further. Use the manufacturer gain-bandwidth and stability guidance to choose feedback resistors and capacitors, and verify settling time for signal-acquisition and process-control applications.
Keep the four amplifier channels on the same 14-lead SOIC electrically quiet and physically separate from switching-regulator outputs, inductors, relay contacts, and high-current return paths. Route outputs directly to their destinations rather than passing them near input pins. Use a continuous ground plane where practical, place input-bias and feedback components close to the associated pins, and account for parasitic capacitance from long traces when driving capacitive loads.
Rail-to-rail operation does not eliminate all supply-rail or common-mode limitations. Check the input and output voltage ranges in the manufacturer datasheet across temperature and process conditions, and avoid driving an output hard against a supply rail when the next stage requires additional headroom. When replacing MCP6044-I/SL with another suffix, verify temperature limits, electrical tolerances, pin names, and qualification rather than relying on package shape alone.
合規資訊
No explicit compliance declaration is included in the manufacturer product information or component listings.