MCP606T-I/SN - 155kHz Micropower Op Amp | Microchip
MPN: MCP606T-I/SN ✓ 啟用中MCP606T-I/SN 概覽
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its two inputs while providing high open-loop gain. The MCP606 belongs to the micropower amplifier segment of the broader linear IC hierarchy, combining low supply consumption with rail-to-rail output capability. This combination makes it suitable for portable instrumentation, low-power sensors, signal conditioning, and battery-powered systems where the output must operate close to the supply rails.
Key electrical characteristics include a 155 kHz gain-bandwidth product, 38 nV/√Hz input-noise density at 1 kHz, 80 V/ms slew rate, and 91 dB open-loop gain. The input offset voltage is specified below 250 µV, while input bias current is listed at 1 pA. Temperature drift is 1.8 µV/°C, supporting stable precision measurements across the industrial temperature range. CMOS input stages provide the low bias current needed to avoid disturbing high-impedance sensor signals.
The MCP606 uses Microchip's advanced CMOS process and is unity-gain stable, allowing operation as a direct buffer without an external compensation network. Rail-to-rail output swing increases usable signal range in low-voltage systems, although input common-mode limits, output-current capability, and stability must be checked against the circuit requirements. Built-in compensation simplifies small-signal layouts, but sensitive analog nodes still require short traces and careful grounding.
Typical uses include portable sensor interfaces, low-power data acquisition, active filtering, microphone preamplification, battery-powered monitors, and general-purpose signal conditioning. Its 18.7 µA typical operating current is particularly useful when every microampere affects battery life. The 155 kHz bandwidth also supports applications requiring modest closed-loop bandwidth rather than high-speed waveform processing.
For layout, place input and output components close to the corresponding pins, maintain a continuous ground reference, and keep high-current return paths away from sensitive input traces. Decoupling capacitors should connect directly between the supply pin and ground. Check the manufacturer's recommended capacitor values, maximum input voltage, common-mode range, and output-load limits before finalizing the circuit.
This page combines the manufacturer specifications, package details, drop-in alternatives, application guidance, and design notes needed to evaluate MCP606T-I/SN for a new low-power analog design. It also distinguishes package-compatible options from variants that require a different footprint, helping engineers select a replacement without overlooking PCB or qualification constraints.
直接替換替代品,適用於 MCP606T-I/SN — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP606T-I/SN (相同外形與佔位) — 差異在於 Package, Typical Operating Current, Amplifier Type, Input Bias Current, Slew Rate.
MCP606T-I/OTVAO
✅ 直接替換📋 參考替代品(不在目錄中)
MCP606-I/SN
✅ 直接替換聯絡詢價
查看資料表 →MCP606T-I/OT
✅ 直接替換聯絡詢價
查看資料表 →MCP606T-I/SN 最大額定值與電氣特性
| Amplifier Type | Single operational amplifier |
| Gain-Bandwidth Product | 155 kHz |
| Typical Operating Current | 18.7 µA |
| Supply Voltage Range | 2.5 V to 6.0 V |
| Input Offset Voltage | Less than 250 µV maximum |
| Input Offset Voltage Drift | 1.8 µV/°C |
| Input Bias Current | 1 pA |
| Input Noise Density | 38 nV/√Hz at 1 kHz |
| Slew Rate | 80 V/ms |
| Open-Loop Gain | 91 dB |
| 輸出類型 | Rail-to-rail output |
| Compensation | Built-in, unity-gain stable |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| RoHS 狀態 | Compliant |
MCP606T-I/SN 腳位配置
| 腳位 1 | NC — Not connected |
| 腳位 2 | −IN — Inverting input |
| 腳位 3 | +IN — Non-inverting input |
| 腳位 4 | V− — Negative supply or ground connection |
| 腳位 5 | NC — Not connected |
| 腳位 6 | OUT — Amplifier output |
| 腳位 7 | V+ — Positive supply connection |
| 腳位 8 | NC — Not connected |
典型應用
MCP606T-I/SN 適用於 6 應用s: Battery-Powered Sensor Interfaces, Portable Medical Monitoring, Industrial IoT Signal Conditioning, Portable Audio Preamplification, Low-Power Data Acquisition, Battery-Powered Voltage Monitoring.
Battery-Powered Sensor Interfaces
The MCP606T-I/SN fits low-power sensor front ends because it operates from 2.5 V to 6.0 V while drawing only 18.7 µA of typical operating current. Its 1 pA listed input bias current minimizes disturbance to high-impedance sensor sources, and the 250 µV maximum input offset supports accurate measurement of small signals. Place the amplifier close to the sensor and ADC input, use the device as a voltage follower where appropriate, and include local supply decoupling to preserve low-noise behavior.
推薦
Portable Medical Monitoring
The MCP606T-I/SN is useful in portable monitoring equipment where each microampere of amplifier current affects battery life. Its low operating current, 155 kHz gain-bandwidth product, and 38 nV/√Hz input-noise density support low-level physiological signal conditioning. The rail-to-rail output allows useful signal span at low supply voltages, although circuit design must account for the device's stated input common-mode limits and provide isolation appropriate to the intended medical application.
推薦
Industrial IoT Signal Conditioning
The MCP606T-I/SN is appropriate for industrial IoT modules that condition low-frequency sensor or switch-state signals without requiring a high-speed amplifier. Its -40 °C to +85 °C rating covers industrial environments, while the 155 kHz bandwidth supports moderate closed-loop gains and active filtering. Use short traces from the transducer, maintain a low-impedance ground return, and avoid routing switching-node or relay-control currents beneath the input network to reduce coupled noise.
推薦
Portable Audio Preamplification
The MCP606T-I/SN can provide low-level audio preamplification in portable microphone or line-level circuits when modest bandwidth is sufficient. Its 38 nV/√Hz input-noise density, 1 pA listed input bias current, and 80 V/ms slew rate support low-noise signal handling, while the 155 kHz gain-bandwidth product favors voice-band rather than high-fidelity wideband applications. Choose passive or active gain values that avoid clipping near the output swing limits.
推薦
Low-Power Data Acquisition
The MCP606T-I/SN is suitable for buffering multiplexed or low-rate data-acquisition channels where power consumption is more important than megahertz bandwidth. A 155 kHz amplifier can provide channel conditioning and active filtering, while 18.7 µA typical operating current limits the amplifier contribution to total system power. Keep the input network close to the ADC driver, use a stable reference and ground arrangement, and verify settling requirements for the selected gain and sampling rate.
推薦
Battery-Powered Voltage Monitoring
The MCP606T-I/SN works well in battery voltage monitors because its 2.5 V to 6.0 V supply range and low 18.7 µA operating current suit compact energy-harvesting and portable systems. Its less-than-250 µV maximum offset can reduce measurement error when the amplifier is used in a non-inverting gain stage, while unity-gain stability allows direct voltage buffering. Account for the amplifier's own input and output limits when monitoring rails near the upper supply boundary.
推薦
推薦產品摘要
工程參考資料,適用於 MCP606T-I/SN — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP606T-I/OTVAO | MCP606-I/SN | MCP606T-I/OT |
|---|---|---|---|---|
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Amplifier Type | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Gain-Bandwidth Product | 155 kHz | 155 kHz | 155 kHz family rating | 155 kHz family rating |
| Supply Voltage Range | 2.5 V to 6.0 V | 2.5 V to 6.0 V | 2.5 V to 6.0 V family rating | 2.5 V to 6.0 V family rating |
| Maximum Input Offset Voltage | 250 µV | 250 µV | 250 µV | 250 µV family rating |
| Typical Operating Current | 18.7 µA | 18.7 µA | 18.7 µA family rating | 18.7 µA family rating |
| Output Type | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output family rating |
主要差異化特點
- Low operating current supports longer battery life (對比MCP606-I/SN)
- Automotive-qualified family option is available in the same SOIC-8 footprint (對比MCP606T-I/OTVAO)
- Rail-to-rail output improves usable span in low-voltage systems (對比MCP606T-I/OT)
設計說明
Place the decoupling capacitor directly between pin 7, V+, and pin 4, V−, with a short ground path. Connect input components close to pins 2 and 3, and route the feedback components from pin 6 without passing through the input region. For high-impedance sources, use a guarded ground or driven shield if leakage and surface contamination could disturb the signal. Keep switching regulators, relays, and high-current return paths physically separated from the analog amplifier.
The MCP606 has a 155 kHz gain-bandwidth product, so its closed-loop bandwidth depends on the selected noise gain. At higher gain, the usable signal range becomes more limited, and added phase delay can cause ringing or instability. Confirm stability with the intended capacitor values, source impedance, output load, and PCB parasitics. The built-in compensation supports unity-gain use, but it does not remove the need to verify each feedback network and load condition.
Estimated: the typical operating current is 18.7 µA, so the amplifier's contribution at 3.3 V is approximately 61.7 µW before considering output-current demand, bias effects, and supply rejection. This calculation is an operating-point estimate rather than a maximum-power rating. The design must also include each support component's consumption and verify that startup transients, output loading, and battery leakage remain within the system power budget.
Do not assume that a rail-to-rail output guarantees rail-to-rail input operation. Check the manufacturer input common-mode limits against the signal range, especially when operating near 2.5 V or 6.0 V. Likewise, verify maximum output swing under the intended load because light-load and capacitive-load behavior can differ. Use the manufacturer pin-description table to keep pins 1, 5, and 8 unconnected and connect the single-supply ground return to pin 4.
合規資訊
The component listing identifies the MCP606T-I/SN as RoHS compliant. No separate REACH, halogen-free, conflict-minerals, or standard-product lead-free statement was identified. Automotive qualification is associated with the MCP606T-I/OTVAO ordering option rather than the target MPN.