MCP6232-E/P - Dual 1.8V Low-Power Rail-to-Rail Op Amp | Microchip
MPN: MCP6232-E/P ✓ 啟用中MCP6232-E/P 概覽
An operational amplifier is a voltage-gain amplifier intended for feedback-based analog signal conditioning. The MCP6231/1R/1U/2/4 family operates from a single supply as low as 1.8 V, combines a 300 kHz typical gain-bandwidth product with approximately 65 degrees of typical phase margin, and is designed for low-power signal processing. Rail-to-rail input and output operation improves usable signal range near the supply rails, although input and output common-mode limits still require careful review for each operating condition.
The MCP6232-E/P is specified as a dual amplifier in an 8-pin PDIP package. The exact ordering code also includes an extended-temperature qualification option, making the through-hole format convenient for prototypes, educational equipment, industrial controllers, and systems assembled with conventional through-hole components. Its rail-to-rail architecture is particularly useful when signals approach either supply rail and cannot be amplified reliably by a conventional amplifier with restricted common-mode range.
The manufacturer describes the MCP6231/1R/1U/2/4 family as combining wide bandwidth with low quiescent current. The family’s typical quiescent current is 20 µA per amplifier, while the MCP6232-E/P listing identifies a 1.8 V minimum operating voltage and approximately 200 kHz bandwidth for the selected orderable variant. These characteristics support compact, low-power designs where every milliampere of supply demand can shorten battery operating time or increase thermal stress.
Typical uses include low-voltage sensor conditioning, current measurement, battery-powered acquisition, audio input stages, transducer interfaces, and general-purpose analog control. In a sensor circuit, the amplifier can provide input buffering and gain referenced to the midpoint of a single supply. In audio applications, its dual configuration can process two channels while reducing package count.
The principal design consideration is the interaction between low supply voltage, rail-to-rail operation, output loading, and operating temperature. Confirm the input common-mode range, output swing, noise, offset, slew rate, and stability against the intended signal before releasing a production design. Place input and feedback components close to the device, maintain the recommended decoupling arrangement, and provide a clean return path to minimize offset and noise pickup.
直接替換替代品,適用於 MCP6232-E/P — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP6232-E/P (相同外形與佔位) — 差異在於 Amplifier Type, Gain-Bandwidth Product, Number of Channels, Package, Phase Margin.
MCP6231-E/P
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6241-E/P
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
MCP6242-E/P
✅ 直接替換聯絡詢價
查看資料表 →MCP6232-E/P 最大額定值與電氣特性
| Amplifier Type | Operational amplifier |
| Number of Channels | 2 |
| Minimum Supply Voltage | 1.8 V |
| 靜態電流 | 20 µA typical per amplifier |
| Gain-Bandwidth Product | 200 kHz for MCP6232-E/P |
| Family Gain-Bandwidth Product | 300 kHz typical |
| Phase Margin | 65 degrees typical |
| Input Type | Rail-to-rail |
| 輸出類型 | Rail-to-rail |
| 封裝 | 8-pin PDIP |
| 安裝類型 | Through-hole |
| Temperature Grade | Extended temperature |
| 腳位數 | 8 |
MCP6232-E/P 腳位配置
| 腳位 1 | OUTA — Amplifier A output |
| 腳位 2 | INA- — Amplifier A inverting input |
| 腳位 3 | INA+ — Amplifier A non-inverting input |
| 腳位 4 | V- — Negative supply or ground connection |
| 腳位 5 | INB+ — Amplifier B non-inverting input |
| 腳位 6 | INB- — Amplifier B inverting input |
| 腳位 7 | OUTB — Amplifier B output |
| 腳位 8 | V+ — Positive supply connection |
典型應用
MCP6232-E/P 適用於 6 應用s: Battery-Powered Sensor Conditioning, Low-Voltage Audio Signal Processing, Industrial Current Measurement, Portable Data Acquisition, Transducer and Bridge Interfaces, Embedded Control Interfaces.
Battery-Powered Sensor Conditioning
The MCP6232-E/P fits battery-powered sensor interfaces because it operates from a single supply as low as 1.8 V and the related family draws only 20 µA typical quiescent current per amplifier. Rail-to-rail inputs help preserve signal information when a sensor operates near either supply rail, while rail-to-rail outputs allow the conditioned voltage to use much of the available range. Place each amplifier in a conventional non-inverting or inverting configuration, connect input and feedback components close to the device, and confirm the sensor’s common-mode range against the exact amplifier limits. Low supply voltage still requires careful grounding and decoupling because small offsets and noise can represent a significant fraction of the sensor’s full-scale output.
推薦
Low-Voltage Audio Signal Processing
The dual MCP6232-E/P can process left and right audio channels in a compact low-voltage system. Rail-to-rail inputs and outputs are useful when the signal occupies a large percentage of a 1.8 V or other low supply, while the approximately 200 kHz bandwidth listed for MCP6232-E/P is appropriate for many low-bandwidth audio and control paths rather than demanding full-range audio specifications. The two independent channels should share a stable supply and ground reference, and each feedback network must be sized for its intended gain. Confirm slew rate, output swing, noise, and stability with the manufacturer characteristic curves before accepting the design as a precision audio stage.
推薦
Industrial Current Measurement
MCP6232-E/P can amplify the small voltage produced by a low-side current shunt or sensor in an industrial measurement front end. A differential amplifier built from the dual device can subtract a reference from the sensor output, improving common-mode rejection and reducing component count. The 1.8 V minimum supply supports compact control systems, and the PDIP package simplifies through-hole assembly and maintenance. The shunt and amplifier must be checked together for common-mode range, input offset, bias-current error, output swing, and bandwidth. Add filtering at the amplifier input when switching transients or motor noise could exceed the electrical limits.
推薦
Portable Data Acquisition
The MCP6232-E/P is suited to portable data-acquisition front ends that must amplify two low-level analog channels within a small power budget. Its single-supply operation from 1.8 V and 20 µA typical family quiescent current reduce the load imposed on batteries or energy-harvesting sources. Rail-to-rail input and output behavior improves usable range in systems where the sensor output does not sit near mid-supply. Use one amplifier channel per input, establish a suitable bias point for single-supply signals, and account for input bias current when using high-impedance sensors. Verify the selected gain against the approximately 200 kHz MCP6232-E/P bandwidth specification before increasing closed-loop gain.
推薦
Transducer and Bridge Interfaces
The two amplifiers in MCP6232-E/P can buffer strain, pressure, temperature, and resistive-bridge sensors in compact instrumentation. Rail-to-rail operation is useful at low supply voltages, and the dual configuration can reduce the number of packages compared with discrete single amplifiers. Bridge excitation and sensing amplifiers must be evaluated for offset, bias current, common-mode range, and noise rather than bandwidth alone; a high source impedance can also introduce errors that appear as output offset. Keep sensitive input traces short, return both channel grounds to the same low-noise reference, and place anti-alias or filtering components where their resistance and capacitance will not degrade the intended measurement accuracy.
推薦
Embedded Control Interfaces
MCP6232-E/P can condition analog control signals between sensors and an embedded controller, including pressure, position, or threshold signals in compact embedded equipment. The 1.8 V minimum operating voltage can simplify sharing a supply with low-voltage digital systems, while the PDIP package supports conventional through-hole prototypes and industrial controller assemblies. Use the amplifier to provide gain, level shifting, buffering, or active filtering, and ensure the controller’s ADC input remains within its input range. Component tolerances directly affect gain accuracy, so use suitable resistor networks and verify offset, common-mode behavior, output settling, and supply-noise rejection in the final board configuration.
推薦
推薦產品摘要
工程參考資料,適用於 MCP6232-E/P — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP6231-E/P | MCP6241-E/P | MCP6242-E/P |
|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Number of Amplifiers | 2 | 2 | 2 | 2 |
| Minimum Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Input and Output Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole |
主要差異化特點
- Two low-power amplifiers in one through-hole package (對比MCP6231-E/P)
- Documented exact-orderable bandwidth (對比MCP6242-E/P)
- Low-voltage rail-to-rail operation (對比MCP6241-E/P)
設計說明
Decouple the supply pins at the device with a short, low-inductance connection to the system ground plane. Place the principal bypass capacitor immediately across the IC supply terminals and retain any additional capacitor recommended by the manufacturer for high-frequency noise control. Avoid placing sensitive inputs next to the supply-return path. Because the related family draws 20 µA typical quiescent current per amplifier, supply demand will often be dominated by the load rather than the op-amp itself.
Keep each input pin, feedback resistor, and compensation component close to its associated amplifier pin. Route outputs away from high-impedance input and feedback nodes to reduce parasitic coupling, and use a continuous ground reference rather than a narrow return path. For single-supply designs, establish the signal midpoint at a quiet, well-decoupled reference. Check the physical orientation against the numbered 8-pin PDIP pinout before soldering.
Do not treat rail-to-rail input and output wording as permission to exceed the electrical limits at elevated temperature, high output load, or low supply voltage. Review the exact manufacturer common-mode, output-swing, offset, slew-rate, and supply-maximum curves. Also avoid assuming that two amplifiers sharing a package can operate from split supplies without checking the permitted total supply voltage and ground configuration.
合規資訊
The orderable is identified as an extended-temperature dual operational amplifier in an 8-pin PDIP package. Specific environmental and material-compliance declarations require confirmation from the manufacturer product documentation.